Siemens Sitrans PROBE LU Manual de instrucciones

Radar Transmitters

Quick Start Manual 12/2013

SITRANS Probe LU (PROFIBUS PA)

SITRANS

IQ300IX.fm Page 5 Tuesday, October 2, 2001 1:43 PM

A5E32081626 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL Page EN-1

mmmmm

English

SITRANS Probe LU (PROFIBUS PA) Quick

Start Manual

This manual outlines the essential features and functions of the SITRANS Probe LU (PROFIBUS PA).

We strongly advise you to acquire the detailed version of the manual so you can use your

instrument to its fullest potential. The complete manual can be downloaded from the Siemens

website at: www.siemens.com/level. The printed manual is available from your local Siemens

representative.

Questions about the contents of this manual can be directed to:

Siemens Milltronics Process Instruments

1954 Technology Drive, P.O. Box 4225

Peterborough, Ontario, Canada, K9J 7B1

Email: [email protected]om

MILLTRONICS is a registered trademark of Siemens Milltronics Process Instruments.

Safety Guidelines

Warning notices must be observed to ensure personal safety as well as that of others, and to

protect the product and the connected equipment. These warning notices are accompanied by

a clarification of the level of caution to be observed.1

Process Instruments 2013.

Disclaimer of Liability

We encourage users to purchase

authorized bound manuals, or to view

electronic versions as designed and

authored by Siemens Milltronics Process

Instruments. Siemens Milltronics

Process Instruments will not be

responsible for the contents of partial or

whole reproductions of either bound or

electronic versions.

While we have verified the contents of this manual

for agreement with the instrumentation described,

variations remain possible. Thus we cannot

guarantee full agreement. The contents of this

manual are regularly reviewed and corrections are

included in subsequent editions. We welcome all

suggestions for improvement.

Technical data subject to change.

WARNING: relates to a warning symbol on the product, and means that failure to

observe the necessary precautions can result in death, serious injury, and/or

considerable material damage.

WARNING1: means that failure to observe the necessary precautions can result

in death, serious injury, and/or considerable material damage.

Note: means important information about the product or that part of the operating manual.

1. This warning symbol is used when there is no corresponding caution symbol on the product.

Page EN-2 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL A5E32081626

mmmmm

English

SITRANS Probe LU (PROFIBUS PA)

SITRANS Probe LU is a 2-wire loop-powered, continuous level monitor that uses advanced

ultrasonic techniques. The instrument consists of an electronic component coupled to the

transducer and process connection.

The transducer is available in ETFE (ethylene-tetrafluoroethylene) or PVDF (polyvinylidene

fluoride), allowing SITRANS Probe LU to be used in a wide variety of industries and

applications using corrosive chemicals.

The ultrasonic transducer contains a temperature-sensing element to compensate for

temperature changes in the application.

Communication is via PROFIBUS PA. This device supports acyclic communications from both a

PROFIBUS Class I and Class II master. Signals are processed using Sonic Intelligence® which

has been field-proven in over 500,000 applications worldwide (ultrasonic and radar).

SITRANS Probe LU is available in three versions:

• General Purpose (non-hazardous)

• Intrinsically Safe (with suitable barrier)

• Non-Incendive (FM Class I, Div. 2)

WARNING: Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

Note: This product is intended for use in industrial areas. Operation of this equipment in a

residential area may cause interference to several frequency based communications.

A5E32081626 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL Page EN-3

mmmmm

English

Specifications

For a complete listing, see the SITRANS Probe LU (PROFIBUS PA) Operating Instructions. For

Approvals information, please refer to the device nameplate1.

Ambient/Operating Temperature

Power

• Bus powered On PROFIBUS PA, as per IEC 61158-2

• Current consumed 12 mA (default value)2

Performance

• Update time with 12 mA loop current26.0 s (typical), maximum 16.0 s3

Approvals

• General CSAUS/C, FM, CE

• Hazardous Intrinsically Safe (Europe) ATEX II 1 G Ex ia IIC T4 Ga

(US/Canada) FM4/CSA4: barrier required

Class I, Div. 1, Groups A, B, C, D

Class II, Div. 1, Groups E, F, G

Class III T4

1. For device nameplate see

Wiring setups for hazardous area installations

on page 7.

Note: Process temperature and pressure capabilities are dependent upon information

on the device nameplate. The reference drawing listed on the nameplate can be

downloaded from the Siemens website. Go to the SITRANS Probe LU product page at:

www.siemens.com/probelu.

2. For 13, 15, or 20 mA options, see

PROFIBUS Current Consumption

on page 16.

3. Temperature dependent: typical value at +20 °C (+68 °F); max. value at +80 °C (+176 °F).

4. See

FM/CSA Intrinsically Safe Connection Drawing

on page 1 of Appendix A, for drawing number

23650617.

flange adaptor (option)

customer-supplied

flange

ambient temperature

surrounding enclosure

–40 to +80 °C (–40 to +176 °F)

process temperature

–40 to +85 °C (–40 to +185 °F)

device nameplate

Page EN-4 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL A5E32081626

mmmmm

English

(Brazil) INMETRO: DNV 12.0084 X

Ex ia IIC T4 Ga

IP67/IP68

-40 ºC ≤ T a ≤ +80 ºC

DNV #OCP 0017

ABNT NBR IEC 60079-0:2008

ABNT NBR IEC 60079-11:2009 e

ABNT NBR IEC 60079-26:2008

Non-incendive (US) FM1:

Class I, Div. 2, Groups A, B, C, D T5

Installation

Mounting location

Recommendations

• Ambient temperature should be within –40 to +80 °C (–40 to +176 °F).

• Provide easy access for viewing the display and programming via the handheld

programmer.

• Provide an environment suitable to the housing rating and materials of construction.

• Keep the sound path perpendicular to the material surface.

1. See

FM: Class I, Div. 2 Connection Drawing

on page 5 of Appendix A, for drawing number 23650583.

Note: Approved dust-tight and water-tight conduit seals are required for outdoor Type 4X /

NEMA 4X, Type 6 / NEMA 6, IP67, IP68 locations..

WARNINGS:

• Installation shall only be performed by qualified personnel and in accordance with

local governing regulations.

• SITRANS Probe LU is to be used only in the manner outlined in this manual,

otherwise protection provided by the equipment may be impaired.

Note: Please refer to the device nameplate for approval information.

A5E32081626 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL Page EN-5

mmmmm

English

Precautions

• Avoid proximity to high voltage or current wiring, high voltage or current contacts, and to

variable frequency motor speed controllers.

• Avoid interference to the sound path from obstructions or from the fill path.

Mounting instructions

SITRANS Probe LU is available in three thread types: 2" NPT, 2" BSP, or PF2/G (BS EN ISO 228-1).

1. Before inserting SITRANS Probe LU into its mounting connection, ensure that the threads

are of the same type to avoid damaging them.

2. Simply screw SITRANS Probe LU into the process connection and hand tighten.

Wiring

Power1

Note: Ideally, mount SITRANS Probe LU so that the face of the transducer is at least

300 mm (1 ft) above the highest anticipated level.

WARNINGS:

DC terminals shall be supplied from an SELV1source in accordance with

IEC-1010-1 Annex H.

All field wiring must have insulation suitable for rated voltages.

1. Safety Extra Low Voltage

seam

ladder

rung

pipe

Fill

The sound path should be:

• perpendicular to the

monitored surface

• clear of rough walls,

seams, rungs, or

other obstructions

• clear of the fill path 10°

Page EN-6 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL A5E32081626

mmmmm

English

Connecting SITRANS Probe LU (PROFIBUS PA)

1. Strip the cable jacket for approximately

70 mm (2.75") from the end of the PROFIBUS PA

cable, and thread the wires through the gland1.

2. Connect the wires to the terminal as shown:

Probe LU (PROFIBUS PA) is not polarity-sensitive.

3. Ground the instrument according to local

regulations.

• For Intrinsically Safe applications, connect

the cable shield to the instrument shield

connection2, and ground the shield

connection to an external ground that is

connected to an equal-potential grounding

grid. For more detail on Explosion

Protection, you can download the brochure

Siemens Process Automation Explosion Protection

(part number A5E00265440) from

www.siemens.com/level, under Brochures/General.

• For General Purpose applications, ground the shield at one point only (usually the

power supply side) and continue the shield from device to device, connecting it to

the shield connection in each Probe LU.

4. Tighten the gland to form a good seal.

5. Close the cover and tighten screws: please do not overtighten screws. Recommended

torque is 0.5 to 1.1 N-m (5 to 10 in-lb).

Note:

• For detailed wiring instructions, please see the full manual.

• For Intrinsically Safe setups (FM/CSA Class I, Div. 1), see

FM/CSA Intrinsically Safe

Connection Drawing

on page 1 of Appendix A, for drawing number 23650617.

• For Non-Incendive setups (FM: Class I, Div. 2), see

FM: Class I, Div. 2 Connection Drawing

on page 5 of Appendix A, for drawing number 23650583.

• The non-metallic enclosure does not provide a continuous ground path between conduit

connections: use grounding-type bushings and jumpers.

• Separate cables and conduits may be required to conform to standard instrumentation

wiring practices, or electrical codes.

1. If cable is routed through conduit, use only approved suitable-size hubs for waterproof applications.

2. The instrument shield connection is internally connected to the external ground lug.

Note: PROFIBUS PA must be terminated at both extreme ends of the cable for it to

work properly. Please refer to the

PROFIBUS PA User and Installation Guidelines

(order

number 2.092), available from www.profibus.com.

shield

wire

A5E32081626 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL Page EN-7

mmmmm

English

Wiring setups for hazardous area installations

Always check the device nameplate and process device tag to verify the approval rating.

1. Intrinsically Safe wiring

• For wiring requirements: follow local regulations.

• Approved dust-tight and water-tight conduit seals are required for outdoor Type 4X /

NEMA 4X, Type 6 / NEMA 6, IP67, IP68 locations.

• Refer to

Instructions specific to hazardous area installations (Reference European

ATEX Directive 94/9/EC, Annex II, 1/0/6)

on page 8.

2. Non-incendive wiring (FM US only)

Profibus PA

Entity:

Ui=24V

Ii=250mA

Pi=1.2W

Ci=1.0nF

Li=0

FISCO:

FieldDevice:

Ui=17.5 V

Ii= 380 mA

Pi= 5.32 W

Ci= 1.0 nF

Li= 0

Power Rating: 30V , 20 mA Max.

Serial No: GYZ / B1034567

Assembled in Canada with domestic and imported parts

Siemens Milltronics Process Instruments, Peterborough

SITRANS Probe LU

7MLxxxx-xxxxx-xxxx Encl.: NEMA/TYPE 4X, 6, IP67, IP68

Amb.Temp.: – 40°C to 80°C

Ex ia IIC T4 Ga

DNV 12.0084 X

0518

Ex ia IIC T4 Ga

SIRA 06ATEX2357X

1GII

ATENÇÃO - RISCO POTENCIAL DE CARGA ELETROSTÁTICA

- VEJA INSTRUÇÕES

KCC-REM-S49

PROBELU

OCP 0017

The ATEX certificate can be downloaded from the product

page of our website at: www.siemens.com/probelu. Go to Support > Approvals /

Certificates.

Device nameplate (ATEX/INMETRO/C-TICK)

Entity:

Ui= 24V

Ii= 250mA

Pi= 1.2W

Ci= 1.0nF

Li= 0

Serial No: GYZ / B1034567 Encl.: NEMA/TYPE 4X, 6, IP67, IP68

Amb.Temp.: – 40°C to 80°C

Power Rating: 30V , 20 mA Max.

Assembled in Canada with domestic and imported parts

Siemens Milltronics Process Instruments, Peterborough

SITRANS Probe LU

7MLxxxx-xxxxx-xxx-x

WARNING: Possible Static Hazard, Do Not Rub Or Clean On Site.

ClassI,Div1,Gr.A,B,C,D; T4

ClassII,Div1,Gr.E,F,G; ClassIII

Exia per drawing: 23650617

Profibus PA

Fisco:

Ui=17.5V

Ii=380 mA

Pi=5.32 W

Ci=1.0 nF

Li=0

159134

FM/CSA Intrinsically Safe connection drawing number 23650617 can be downloaded from

the product page of our website at: www.siemens.com/probelu. Go to Support > Installation

Drawings > Level Measurement > Continuous - Ultrasonic.

Device nameplate (FM/CSA)

Class I,Div.2,

Group A,B,C,D

Temp.Code:T5

PROFIBUSPA

Serial No: GYZ / S1034567 Encl.: NEMA/TYPE 4X, 6, IP67, IP68

Amb.Temp.: – 40°C to 80°C

Power Rating: 30V , 20 mAMax.

Assembled in Canada with domestic and imported parts

Siemens Milltronics Process Instruments, Peterborough

SITRANS Probe LU

7ML1234-78910-ABC-D

FM Class 1, Div 2 connection drawing

number 23650583 can be downloaded from the product page of our website at:

www.siemens.com/probelu. Go to Support > Installation Drawings > Level Measurement >

Continuous - Ultrasonic.

Page EN-8 SITRANS Probe LU (PROFIBUS PA) – QUICK START MANUAL A5E32081626

mmmmm

English

Instructions specific to hazardous area installations

(Reference European ATEX Directive 94/9/EC, Annex II, 1/0/6)

The following instructions apply to equipment covered by certificate number SIRA

06ATEX2357X:

1. For use and assembly, refer to the main instructions.

2. The equipment is certified for use as Category 1G equipment.

3. The equipment may be used with flammable gases and vapors with apparatus

group IIC and temperature class T4.

4. The equipment is certified for use in an ambient temperature range of –40 C to

80 C.

5. The equipment has not been assessed as a safety related device (as referred to by

Directive 94/9/EC Annex II, clause 1.5).

6. Installation and inspection of this equipment shall be carried out by suitably trained

personnel in accordance with the applicable code of practice (EN 60079-14 and

EN 60079-17 in Europe).

7. Repair of this equipment shall be carried out by suitably trained personnel in

accordance with the applicable code of practice (e.g. EN 60079-19 within Europe).

8. Components to be incorporated into or used as replacements in the equipment shall

be fitted by suitably trained personnel in accordance with the manufacturer’s

documentation.

9. It is the responsibility of the user to ensure that manual override is possible in order

to shut down the equipment and protective systems incorporated within automatic

processes which deviate from the intended operating conditions, provided that this

does not compromise safety.

10. The ‘X’ suffix to the certificate number relates to the following special conditions for

safe use:

a. Parts of the enclosure may be non-conducting and may generate an ignition-

capable level of electrostatic charge under certain extreme conditions. The

user should ensure that the equipment is not installed in a location where it

may be subjected to external conditions (such as high-pressure steam) which

might cause a build-up of electrostatic charge on non-conducting surfaces.

b. As either Aluminum, Magnesium, Titanium or Zirconium

may be used at the

accessible surface of the equipment, in the event of rare incidents, ignition

sources due to impact and friction sparks could occur. This shall be considered

when the SITRANS Probe LU (PROFIBUS PA) is being installed in locations that

specifically require group II, category 1G equipment.

Otros manuales para sitrans PROBE LU

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Siemens

Siemens

Siemens SITRANS P 7MF1580 Series Manual de usuario

Siemens

Siemens SITRANS FUS060 PA Manual de usuario

Siemens

Siemens SITRANS P series Guía del administrador

Siemens

Siemens sitrans PROBE LU Manual de usuario

Siemens

Siemens Sitrans LU-180 Manual de usuario

Siemens

Siemens SITRANS LR260 Manual de usuario

Siemens

Siemens SITRANS TH100Slim Guía del administrador

Siemens

Siemens SITRANS P410 Guía del administrador

Siemens

Siemens SITRANS LR260 Manual de instrucciones

Siemens

Siemens SITRANS P500 Guía del administrador

Siemens

Siemens SITRANS P Guía del administrador

Siemens

Siemens Sitrans LR250 Guía del administrador

Siemens

Siemens Sitrans LR250 Manual de instrucciones

Siemens

Siemens SITRANS LR110 Manual de usuario

Siemens

Siemens SITRANS LR260 Guía del usuario

Siemens

Siemens SITRANS LR260 Manual de instrucciones

Siemens

Siemens sitrans lr 460 Manual de usuario

Siemens

Siemens Sitrans LR250 Manual de usuario

Siemens

Siemens SITRANS F M Intermag 2 Manual de usuario

Siemens

Siemens Sitrans LR250 Manual de usuario

Siemens

Siemens TRANSMAG 2 Manual de usuario

Siemens

Siemens SITRANS L Series Guía del administrador

Siemens

Siemens SITRANS LR260 Manual de usuario

Siemens

Siemens SITRANS TF2 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Siemens sitrans PROBE LU Manual de instrucciones

Manuales populares de Transmisor de otras marcas