Siemens RDF301 Manual de usuario

CE1N3171en

2012.10-04 Building Technologies

3171

RDF301 RDF301.50

RDF600KN

Semi flush-mount

room thermostats

with KNX communications

RDF301

RDF301.50

RDF600KN

For 2-pipe, 2-pipe with electrical heater, and 4-pipe fan coil units

For use with compressors in DX type equipment

KNX bus communications (S-mode and LTE mode)

Backlit display

2P / PI / P control

Outputs for on/off or 3-position control

Outputs for 3-speed or 1-speed fan

2 multifunctional inputs for keycard contact, external sensor, etc.

Operating modes: Comfort, Economy and Protection

Automatic or manual fan speed control

Automatic or manual heating/cooling changeover

Minimum and maximum limitation of room temperature setpoint

Control depending on the room or the return air temperature

Adjustable commissioning and control parameters

Commissioning with Synco ACS, ETS or via local HMI

Integration into Synco

Integration into Desigo and Apogee via group addressing (ETS) or via

individual addressing

Integration into third-party system via group addressing (ETS)

AC 230 V operating voltage

2 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Additional RDF301.50 features:

Four buttons to control KNX actuators via KNX S-mode

(functions: switching, dimming, blinds control, 8-bit scene)

Type of mounting / suitable conduit boxes

RDF600KN for round box, with min 60 mm diameter, min 40 mm depth

RDF301... for recessed rectangular box with 60.3 mm fixing centers

Use

Room temperature control (heating or cooling) in individual rooms and zones by

means of:

2-pipe fan coil units

2-pipe fan coil units with electrical heater

4-pipe fan coil units

Compressors in DX-type equipment

Compressors in DX-type equipment with electrical heater

The RDF301... / RDF600KN controls:

One single or 3-speed fan

One or two on/off valve actuators

One on/off valve actuator and one 1-stage electrical heater

One 3-position valve actuator

One 1-stage compressor in DX-type equipment, or one 1-stage compressor with

electrical heater

Used in systems with:

Heating or cooling mode

Automatic heating/cooling changeover

Manual heating/cooling changeover

Heating and cooling mode (e.g. 4-pipe system)

The room thermostats are delivered with a fixed set of applications.

The relevant application is selected and activated during commissioning using one

of the following tools:

Synco ACS

ETS

Local DIP switch and HMI

Functions

Maintain room temperature via built-in temperature sensor or external room

temperature / return air temperature sensor

Changeover between heating and cooling mode (automatic via local sensor or

bus, or manual)

Select application via DIP switches or commissioning tool (ACS, ETS)

Select operating mode via operating mode button on the thermostat

Temporary Comfort mode extension

Single speed or 3-speed fan control (automatic or manual)

Display current room temperature or setpoint in °C and/or °F

Minimum and maximum limitation of room temperature setpoint

Button lock (automatic and manual)

3 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Two multifunctional inputs, freely selectable for:

Operating mode switchover contact (keycard)

Automatic heating/cooling changeover sensor

External room temperature sensor or return air temperature sensor

Dewpoint sensor

Electrical heater enable

Fault input

Monitor input for temperature sensor or switch status

Advanced fan control function, e.g. fan kick, fan start, selectable fan operation

(enable, disable or depending on heating or cooling mode)

Purge function together with 2-port valve in a 2-pipe changeover system

Reminder to clean filters

Floor heating temperature limit

Reload factory settings for commissioning and control parameters

KNX bus (terminals CE+ and CE-) for communication with Synco or KNX

compatible devices

Display of outdoor temperature or time of day via KNX bus

Time scheduling and central control of setpoints via KNX bus

With a Synco RMx7xx controller, the energy demand signal of the thermostat is

used to optimize energy supply.

RDF301.50 only:

Four buttons to control KNX actuators via KNX S-mode

("switching groups" with functions such as switching, dimming, blinds control,

8-bit scene)

Applications

The thermostats support the following applications, which can be configured using

the DIP-switches on the inner side of the thermostat's front panel or a commissio-

ning tool.

All DIP switches need to be set to OFF (remote configuration, factory setting) to

select an application via commissioning tool.

Applications and control outputs DIP-switches

Remote configuration via commissioning tool (factory setting)

Synco ACS

ETS 1

2-pipe, on/off

1-stage compressor, on/off

2-pipe fan coil unit

heating or cooling

2-pipe, modulating, 3-position

2-pipe fan coil unit

with electrical heater

heating or cooling

2-pipe with electrical heater, on/off

1-stage compressor with electrical heater, on/off

4-pipe fan coil unit

heating and cooling

4-pipe on/off

Compressor, on/off

4 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Type summary

Product

number

Stock

number

Operating

voltage Control outputs

3-pos on/off DC 0...10 V KNX switching

groups

Suitable

conduit

box 1)

RDF301 S55770-T104 AC 230 V -- rectangular

RDF301.50 S55770-T105 AC 230 V -- rectangular

RDF600KN S55770-T293 AC 230 V --

round

1) Rectangular conduit box e.g. ARG71.

Round conduit box min 60 mm diameter and min 40 mm depth

Ordering

When ordering, indicate both product number / SSN number and name:

E.g. RDF301 / S55770-T104 room thermostat

Order valve actuators separately.

Equipment combinations

Type of unit Product no. Data

sheet

Cable temperature sensor QAH11.1 1840

Room temperature sensor QAA32 1747

Condensation detector / Supply unit

QXA2000 /

QXA2001 /

AQX2000

1542

Electromotoric on / off valve and actuator

(only available in AP, UAE, SA and IN)

MVI…/MXI… 4867

Electromotoric on / off actuator SFA21... 4863

Thermal actuator (for radiator valve)

STA23...

STA21... *)

4884

4893 *)

Thermal actuator

(for small valves 2.5 mm)

STP23...

STP21... *)

4884

4893 *)

Zone valve actuators

(only available in AP, UAE, SA and IN) SUA… 4832

Electrical actuator, 3-position

(for radiator valve) SSA31... 4893

Electrical actuator, 3-position

(for small valve 2,5 mm) SSP31… 4864

Electrical actuator, 3-position

(for small valve 5,5 mm) SSB31... 4891

Electrical actuator, 3-position

(for small valve 5,5 mm) SSD31... 4861

Electromotoric actuator, 3-position

(for valves 5.5 mm) SQS35… 4573

*) Not available any more

On / off actuators

3-position actuators

5 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Accessories

Designation Product no / SSN Data

sheet

Changeover mounting kit

(50 pcs/package) ARG86.3 N3009

Plastic mounting bracket for semi-

flush-mount thermostats RDF301... for

increasing the headroom in the conduit

box by 10mm

ARG70.3 N3009

Conduit box for semi-flush mounted

thermostat RDF301...

ARG71 /

S55770-T137

N3009

KNX Power supply 160 mA (Siemens BT LV) 5WG1 125-1AB02 --

KNX Power supply 320 mA (Siemens BT LV) 5WG1 125-1AB12 --

KNX Power supply 640 mA (Siemens BT LV) 5WG1 125-1AB22 --

Mechanical design

The thermostats consist of 2 parts:

Front panel with electronics, operating elements and built-in room temperature

sensor.

Mounting base with power electronics.

The rear of the mounting base contains the screw terminals.

Slide the front panel in the mounting base and snap on.

Operation and settings

RDF301, RDF600KN RDF301.50

1 Operating mode selector

2 Change fan operation

3 Adjust setpoint and control parameters

4 Four buttons to control KNX actuators via KNX S-mode

(functions: switching, dimming, blinds control, 8-bit scene)

4 4

6 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Display

1 Operating mode

Protection

Comfort

Economy

Auto Timer according to

schedule (via KNX)

2 Displays room temperature, set-

points and control parameters.

Symbol indicates current room

temperature

3 Fan mode

Auto fan active

Fan speed

low, medium, high

4 Heating/cooling mode

Cooling

Heating

Electrical heater active

5Condensation in room

(dewpoint sensor active)

6 Indicates fault or reminder

7 Temporary comfort mode

extension active

8 Additional user information, like

outdoor temperature or

time of day from KNX bus.

Selectable via parameters

9 Button lock active

Weekday 1…7 from KNX bus

(1 = Monday / 7 = Sunday)

Engineering notes

See the "Reference documentation", page 11 for information on how to engineer

the KNX bus (topology, bus repeaters, etc.) and how to select and dimension

connecting cables for supply voltage and field devices.

Mounting and installation

Mount the room thermostat on a conduit box. Do not mount on a wall in niches or

bookshelves, behind curtains, above or near heat sources, or exposed to direct

solar radiation. Mount about 1.5 m above the floor.

Mounting / Dismounting

Mount the room thermostat on a clean, dry indoor place without direct airflow

from a heating / cooling device, and not exposed to drips or splash water.

RDF301… : In case of limited space in the conduit box use the mounting

bracket ARG70.3 to increase the headroom by 10mm

Before removing the front cover, disconnect the power supply.

2 5

3 8

6 9

7 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Wiring See the mounting instructions M3171... enclosed with the thermostat.

Comply with local regulations to wire, fuse and earth the thermostat.

Properly size the cables to the thermostat, fan and valve actuators for AC 230

V mains voltage.

Use only valve actuators rated for AC 230 V.

The AC 230 V mains supply line must have an external fuse or circuit breaker

with a rated current of no more than 10 A.

Cables of SELV inputs X1-M/X2-M: Use cables with 230 V insulation, as the

conduit box carries AC 230 V mains voltage.

Inputs X1-M or X2-M of different units (e.g. summer/winter switch) may be

connected in parallel with an external switch. Consider overall maximum

contact sensing current for switch rating.

KNX communication cables (input CE+ / CE-): Use cables with 230 V

insulation, as the conduit box carries AC 230 V mains voltage.

No metal conduits.

No cables provided with a metal sheath.

Disconnect from supply before opening the cover.

Commissioning notes

The room thermostats are delivered with a fixed set of applications.

Select and activate the relevant application during commissioning using one of the

following tools:

Local DIP switch and HMI

Synco ACS

ETS

Set the DIP switches before snapping the front panel to the mounting plate, if you

want to select an application via DIP switches.

All DIP switches need to be set to “OFF” ("remote configuration"), if you want to

select an application via commissioning tool.

After power is applied, the thermostat resets and all LCD segments flash, indica-

ting that the reset was correct. After the reset, which takes about 3 seconds, the

thermostat is ready for commissioning by qualified HVAC staff.

If all DIP switches are OFF, the display reads "NONE" to show that an application

needs to be set via tool.

Each time the application is changed, the thermostat reloads the factory setting for

all control parameters, except for KNX device and zone addresses!

Applications

Note

8 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Connect the Synco ACS or ETS tools to the KNX bus cable at any point for

commissioning:

NY11 Y21

X1 M X2

3171A03

Q1 Q2 Q3

CE+ CE-

KNX

V24

ETS

RS232

Siemens

N148 /

UP146 /

UP152

KNX

USB

ETS / ACS

Siemens

OCI700

ACS and ETS require an interface:

RS232 KNX interface (e.g. Siemens N148 / UP146 / UP152)

OCI700 USB- KNX interface

An external KNX bus power supply is required if an RDF301... / RDF600KN is

connected directly to a tool (ACS or ETS) via KNX interface.

The thermostat's control parameters can be set to ensure optimum performance of

the entire system (see basic documentation P3171).

The parameters can be adjusted using

Local HMI

Synco ACS

ETS

The control sequence may need to be set via parameter P01 depending on the

application. The factory setting for the 2-pipe application is “Cooling only”; and

“Heating and Cooling” for the 4-pipe application.

When the thermostat is used with a compressor, adjust the minimum output on-

time (parameter P48) and off-time (parameter P49) for Y11/Y21 to avoid

damaging the compressor or shortening its life due to frequent switching.

Recalibrate the temperature sensor if the room temperature displayed on the

thermostat does not match the room temperature measured (after min. 1 hour of

operation). To do this, change parameter P05.

We recommend to review the setpoints and setpoint ranges (parameters

P08…P12) and change them as needed to achieve maximum comfort and save

energy.

The programming mode helps identify the thermostat in the KNX network during

commissioning.

Press buttons “operating mode” and “+” simultaneously for 6 sec to activate

programming mode, which is indicated on the display with "PrOg".

Programming mode remains active until thermostat identification is complete.

Connect tool

Note

Control parameters

Control sequence

Compressor-based

application

Calibrate sensor

Setpoint and range

limitation

Programming mode

9 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Use ETS to assign the KNX group addresses of the RDF communication objects.

RDF301.50 has 2 switching groups with a pair of buttons each, which must be

configured via ETS. The switching groups only work on S-mode.

Each device has a unique KNX serial number inside the front panel. An additional

sticker with the same KNX serial number is enclosed in the packaging box. This

sticker is intended for installers for documentation purposes.

Disposal

This device is classified as waste electronic equipment under European Directive

2002/96/EC (WEEE) and may not be disposed of as unsorted municipal waste.

Adhere to all relevant national laws.

Regarding disposal, use the systems setup for collecting electronic waste.

Observe all local and applicable laws.

Technical data

Power supply Rated voltage AC 230 V

Frequency 50/60 Hz

Power consumption

RDF301...

RDF600KN

Max. 4VA / 3.0W

Max 1.2VA / 3.5W

Outputs Fan control Q1, Q2, Q3-N

Rating

AC 230 V

Min. 5 mA, Max. 5(2) A

Control output Y11-N / Y21-N (NO)

Rating

Max. total load current through terminal “L” (Qx+Yxx)

AC 230 V

Min. 5 mA, Max. 5(2) A

Max. 7A

Inputs

Multifunctional input X1-M/X2-M

Temperature sensor input:

Type

Temperature range

Cable length

Digital input:

Operating action

Contact sensing

Parallel connection of several thermostats

for one switch

Insulation against mains voltage (SELV)

QAH11.1 (NTC)

0...49 °C

Max. 80 m

Selectable (NO / NC)

SELV DC 0...5 V/max 5 mA

Max. 20 thermostats per

switch

4 kV, reinforced insulation

Function of inputs:

External temperature sensor, heating/cooling

changeover sensor, operating mode switchover

contact, dewpoint monitor contact, enable electrical

heater contact, fault contact, monitoring input

Selectable

X1: P38

X2: P40

KNX bus Interface type KNX, TP1-64

(electrically isolated)

Bus current RDF301

RDF600KN

20 mA

5 mA

Bus topology: See KNX manual (reference documentation, see below)

Assign KNX group

addresses

Switching groups

RDF301.50 only

KNX serial number

10 / 14

Siemens RDF301. / RDF301.50 / RDF600KN CE1N3171en

Building Technologies Semi flush-mount room thermostats with KNX communications 2012.10-04

Operational data Switching differential, adjustable

Heating mode (P30)

Cooling mode (P31)

2 K (0.5...6K)

1 K (0.5...6K)

Setpoint setting and range

Comfort (P08)

Economy (P11-P12)

Protection (P65-P66)

21°C (5...40 °C)

15°C/30°C (OFF, 5...40 °C)

8°C/OFF (OFF, 5...40 °C)

Multifunctional input X1/X2

Input X1 default value (P38)

Input X2 default value (P40)

Selectable 0...8

3 (Operating mode

switchover)

1 (External temperature

sensor)

Built-in room temperature sensor

Measuring range

Accuracy at 25 °C

Temperature calibration range

0…49 °C

< ± 0.5 K

± 3.0 K

Settings and display resolution

Setpoints

Current temperature value displayed

0.5 °C

Environmental conditions Operation

Climatic conditions

Temperature

Humidity

As per IEC 721-3-3

Class 3K5

0...50 °C

<95 % r.h.

Transport

Climatic conditions

Temperature

Humidity

Mechanical conditions

As per IEC 721-3-2

Class 2K3

25...60 °C

<95 % r.h.

Class 2M2

Storage

Climatic conditions

Temperature

Humidity

As per IEC 721-3-1

Class 1K3

25...60 °C

<95 % r.h.

Standards and directives conformity

EMC directive

Low-voltage directive

2004/108/EC

2006/95/EC

C-tick conformity to EMC emission standard AS/NZS 61000.6.3: 2007

Reduction of hazardous substances 2002/95/EC

Product standards

Automatic electrical controls for household and

similar use

Special requirements for temperature-dependent

controls

Electronic control type

Home and Building Electronic Systems

EN 60730–1

EN 60730–2-9

2.B (micro-disconnection on

operation)

EN 50090-2-2

Electromagnetic compatibility

Emissions (residential)

Immunity (industrial and residential)

IEC/EN 61000-6-3

IEC/EN 61000-6-2

Safety class II as per EN 60730

Pollution class Normal

Degree of protection of housing IP 30 as per EN 60529

Otros manuales para RDF301

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Siemens

Siemens

Siemens QMX2.P33 Manual de usuario

Siemens

Siemens RDF600T Manual de usuario

Siemens

Siemens RDH100RF/SET Manual de usuario

Siemens

Siemens RDE100 Series Manual de usuario

Siemens

Siemens Free Energy Band TH 193 HC Manual del propietario

Siemens

Siemens TH 192 DN Manual de usuario

Siemens

Siemens RDG100KN Manual de usuario

Siemens

Siemens RDG100 Series Manual de usuario

Siemens

Siemens RDD100.1DHW Manual de usuario

Siemens

Siemens RDG400KN Manual de usuario

Siemens

Siemens RDJ100 Manual de usuario

Siemens

Siemens RDJ100RF/SET Manual de usuario

Siemens

Siemens Landis & Staefa REV26 series Manual de usuario

Siemens

Siemens RAB10 Series Manual del propietario

Siemens

Siemens RDG400 Manual de usuario

Siemens

Siemens RDH100 Manual de usuario

Siemens

Siemens BRTRF Manual de usuario

Siemens

Siemens ZIEHL TR 1200 Manual de usuario

Siemens

Siemens RDF300 Series Manual del operador

Siemens

Siemens RDE50.1 Manual de usuario

Siemens

Siemens RDD100.1RFS Manual de usuario

Siemens

Siemens REA23.03RF Manual de usuario

Siemens

Siemens RDD310/EH Manual de usuario

Siemens

Siemens RDS120 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario