Siemens WAC 12 Manual de usuario

8AA9992 - D1 - 10/11/2000 - UK -

Fig. 1

Fig. 2b

Fig. 3

Fig. 2a

3.2 Product overview (Fig. 2)

- Knockouts Q, Tfor cable inlet.

- Knockouts W, Efor attachment of housing.

- Knockout Rback tamper contact.

- Speaker Y.

- WMC 12 circuit board U.

3.3 WMC 12 circuit board (Fig. 3)

- E-Bus connection }.

- Audio connection {to central control unit.

- Audio connection Ito WAC 11 or WAS 11.

- Tamper input Ofor WAC 11 or WAS 11.

- LED Q, flashes when E-Bus is o.k.

- LED R, flashes to outside during monitoring (microphone

active).

- Address button W.

- Switch Efor "microphone active" LED.

- Tamper switch P.

- Microphone Y.

- Potentiometer Tfor speaker volume.

- Potentiometer Ufor microphone sensitivity.

1. Product description

The WAC 12 is used to verify audio alarms. It is fitted with a

speaker and microphone. It can be controlled through the E-

Bus, with the audio signal connected to the central control unit

via an audio module (e.g. WMA 11). The WAC 12 also serves as

a master for the unaddressable WAC 11 and WAS 11.

2. Supply package

The WAC 12 UK package contains the following

- One WAC 12

- One WLC 12 UK language kit complete with:

- Installation instructions.

3. Mounting instructions

The WAC 12 is designed for mounting in dry indoor rooms.

To ensure good acoustics, note the following points.

- Mount 2 to 2.5 m above floor level.

- Maintain adequate distance from noise sources (ventilation

openings, fans etc.).

- Direct towards the centre of the space to be monitored.

- Do not mount on vibrating surfaces.

- The maximum length of the audio connection between the

WAC 12 and central control unit is 200 m.

3.1 Opening the housing (Fig.1)

1 - Using screwdriver Q, press locking tab to release.

2 - Lift off cover W.

Installation Instructions

WAC 12

WLC 12 UK

20 800 042.0-010

Fig. 4

Fig. 5a

E-Bus from the cen-

tral control unit

E-Bus to other

accessories

Fig. 5b

WAC 12 WAC/WAS 11

Audio to

other

WAC 12

Fig. 5c

e.g. WMA 11 WAC 12

WAS 11

Fig. 5d

WAC 12 WAC 11 WAC 11

The right to make technical changes to the described equipment without prior notice is

reserved.

3.4 Mounting (Fig. 4)

- The housing can be mounted flat or at 45o.

- Always use two attaching points which are one above the

other, including for corner mounting.

4. Wiring

4.1 E-Bus (Fig. 5a)

The use of type 24 AWG 7x0,2 mm dia. cable is recommended.

The E-Bus cable shall not be more than 500 m long. The WAC 12

must be connected to the central control unit via the E-Bus (B1-,

B2, B3, B4+). It can be routed parallel to other accessories.

4.2 Tamper (Fig. 5a)

The tamper inputs T- and T+ must be short-circuited if not wired

to a WAC 11 or WAS 11.

4.3 Audio (Fig. 5b)

To avoid side-tone, a twisted core pair at least 0.6 mm in dia.

must be used. The audio connection to the central control unit

must not be more than 200 m long. The audio output depends

on the cable length and core cross-section. The audio connection

(A- and A+) of the WAC 12 must be connected to the audio input

(A- and A+) of the central control unit (e.g. WMA 11).

4.3.1. WAC 11 and WAS 11 (Fig. 5c)

The audio outputs (A- and A+) of the WAC 11 and WAS 11 are

connected to the audio inputs (AE- and AE+) of the WAC 12. The

tamper outputs (T,T) of the WAC 11 and WAS 11 are connected

in series to the tamper inputs (T- and T+) of the WAC 12.

Where several WAC 11 are used, all WAC 11 must be connected

directly to the WAC 12 to obtain optimum performance (Fig. 5d).

5. Start-up

5.1 Microphone sensitivity

The sensitivity of the microphone must be matched to the room

and ambient noises (potentiometer U, Fig. 3).

Where sensitivity is reduced, the reception of quiet signals

naturally reduces. The following ranges are normally obtained.

- Approx. 3.5 m with potentiometer on min.

- Approx. 6.5 m with potentiometer on mid position.

- Approx. 8.5 m with potentiometer on max.

5.2 Speaker

Set the required volume using potentiometer (Y, Fig. 3).

5.3 LED „microphone active“

- Switch (E, Fig. 3) open: LED active.

- Switch (E, Fig. 3) closed: LED inactive.

6. Close housing

1 - Engage cover at the top in the openings in the base of the

housing.

2 - Close the cover by pushing downwards until the locking

tab engages.

7.Technical data

Supply Through E-Bus

Power consumption, quiescent state 5 mA

Power consumption, "challenge" state 24 mA

Operating temperature -10°C to +55°C

Housing material ABS

Dimension in mm H 145 x B 105 x T 70

Safety class IP 30

Weight 230g

T+

T- B2 B3 B4+

B1-

A+

A-

A+

A-

T+

T-

AE+

AE- TTA-A+

NC TTA-A+

A+ A+

A- A-

AE+

AE-

Tabla de contenidos

Otros manuales de Sistema de seguridad de Siemens

Siemens

Siemens FDM231-RP Manual de usuario

Siemens

Siemens HMS-S Manual de usuario

Siemens

Siemens DMS8000 Manual técnico

Siemens

Siemens 3SX3235 Manual de usuario

Siemens

Siemens FDM221 Manual de usuario

Siemens

Siemens IC60 Manual de usuario

Siemens

Siemens Novigo Core Manual de servicio

Siemens

Siemens SISTORE AX4 Manual de usuario

Siemens

Siemens FC700A Especificaciones técnicas

Siemens

Siemens FS20 Guía del usuario

Siemens

Siemens NCC-G16 Manual de usuario

Siemens

Siemens SPCY130 Manual de usuario

Siemens

Siemens milltronics MFA 4P Manual de usuario

Siemens

Siemens FS20 Instrucciones de funcionamiento

Siemens

Siemens SISTORE AX4 Manual de usuario

Siemens

Siemens 3SX3235 Manual de usuario

Siemens

Siemens FDM223-Ex Manual de usuario

Siemens

Siemens FT2009-U1 Manual de usuario

Siemens

Siemens FDAI91 Manual de usuario

Siemens

Siemens MM8000 Guía de configuración rápida

Siemens

Siemens IC60 Manual de usuario

Siemens

Siemens FDM275 Guía

Siemens

Siemens SIPASS SK5 Manual de instalación y operación

Siemens

Siemens MI290A Guía

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

DSC

DSC PC 4010 Manual del propietario