Siemens SIMATIC NET CP 1628 Manual de usuario

CP 1628

SIMATIC NET

PG/PC - Industrial Ethernet

CP 1628

Operating Instructions

06/2021

C79000

-G8976-C280-09

Preface

Description of the device

Software installation

Hardware installation

Configuration

Technical specifications

Approvals

Siemens AG

Digital

Industries

Postfach 48 48

90026 NÜRNBERG

GERMANY

C79000-G8976-C280-09

Ⓟ

06/2021 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CP 1628

Operating Instructions, 06/2021, C79000-G8976-C280-09 3

Table of contents

1 Preface ................................................................................................................................................... 5

2 Description of the device....................................................................................................................... 9

3 Software installation ........................................................................................................................... 13

3.1 Installing the driver............................................................................................................ 13

3.2 Installing the "SIMATIC NET PC Software"............................................................................ 13

3.3 Uninstalling the "SIMATIC NET PC Software" ....................................................................... 14

4 Hardware installation .......................................................................................................................... 15

5 Configuration....................................................................................................................................... 17

5.1 Configuring Security .......................................................................................................... 18

6 Technical specifications....................................................................................................................... 19

A Approvals............................................................................................................................................. 21

Table of contents

CP 1628

4Operating Instructions, 06/2021, C79000-G8976-C280-09

CP 1628

Operating Instructions, 06/2021, C79000-G8976-C280-09 5

Preface

What the consignment contains

The following components are supplied with the CP 1628:

•CP 1628 communications processor

•DVD "Security Configuration Tool" (or driver/software CD for the CP 1628)

•Safety notices for the CP 1628

•"SIMATIC NET PC Software" DVD

•"SIMATIC STEP 7 Professional" DVD

Please check that the consignment you have received is complete. If the consignment is

incomplete, contact your supplier or your local Siemens office.

Validity of this documentation

These operating instructions are valid for the following product:

•CP 1628

Article number: 6GK1162-8AA00

Content of this documentation

These operating instructions contain information about the installation and configuration of

the CP 1628 communications processor.

Updated operating instructions on the Internet

You will find the current version of these operating instructions on the Product Support pages

under the following entry ID:

62611659 (https://support.industry.siemens.com/cs/ww/en/view/62611659)

Preface

CP 1628

6Operating Instructions, 06/2021, C79000-G8976-C280-09

Further documentation

The documents listed below contain more detailed information on commissioning and using

the communications processor.

Enter the entry ID shown below of the relevant manual as the search item.

•Configuration manual Commissioning PC Stations

This provides you with detailed information on commissioning and configuring SIMATIC

NET PC communications modules.

Entry ID:

77377601 (https://support.industry.siemens.com/cs/ww/en/view/77377601)

•SIMATIC NET - Industrial Communication with PG/PC

–Volume 1 – Basics (system manual)

Entry ID:

77376110 (https://support.industry.siemens.com/cs/ww/en/view/77376110)

–Volume 2 – Interfaces (programming manual)

Entry ID:

77378184 (https://support.industry.siemens.com/cs/ww/en/view/77378184)

The system manuals introduce the topic of industrial communication and explain the

communications protocols used. There is also a description of the OPC interface as user

programming interface.

•Installation manual SIMATIC NET PC Software

This document contains detailed information on installing the "SIMATIC NET

PC Software".

Entry ID:

77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)

•System manual Industrial Ethernet Network Manual

In this document you will find detailed information about setting up an Industrial Ethernet

network.

Entry ID:

27069465 (https://support.industry.siemens.com/cs/ww/en/view/27069465)

SIMATIC NET documentation

You will find the entire SIMATIC NET documentation on the Product Support pages:

15247 (https://support.industry.siemens.com/cs/ww/en/ps/15247)

Go to the required product group and make the following settings:

→Filter criteria for entries → entry type "Manual"

See also

Support (https://support.industry.siemens.com/cs/ww/en/ps)

Preface

CP 1628

Operating Instructions, 06/2021, C79000-G8976-C280-09 7

Trademarks

The following and possibly other names not identified by the registered trademark sign ® are

registered trademarks of Siemens AG:

HARDNET, SOFTNET, CP 1612, CP 1613, CP 5612, CP 5613, CP 5614, CP 5622

Industry Online Support

In addition to the product documentation, you are supported by the comprehensive online

information platform of Siemens Industry Online Support at the following Internet address:

Link: (https://support.industry.siemens.com/cs/de/en/)

Apart from news, there you will also find:

•Project information: Manuals, FAQs, downloads, application examples etc.

•Contacts, Technical Forum

•The option submitting a support query:

Link: (https://support.industry.siemens.com/My/ww/en/requests)

•Our service offer:

Right across our products and systems, we provide numerous services that support you in

every phase of the life of your machine or system - from planning and implementation to

commissioning, through to maintenance and modernization.

You will find contact data on the Internet at the following address:

Link: (https://www.automation.siemens.com/aspa_app/?ci=yes&lang=en)

SITRAIN - Training for Industry

The training offer includes more than 300 courses on basic topics, extended knowledge and

special knowledge as well as advanced training for individual sectors - available at more than

130 locations. Courses can also be organized individually and held locally at your location.

You will find detailed information on the training curriculum and how to contact our

customer consultants at the following Internet address:

Link: (https://sitrain.automation.siemens.com/DE/sitrain/default.aspx?AppLang=en)

Industrial Networks Education

Training and certification for Industrial Networks

In our Industrial Networks Education courses you’ll learn to design and implement wired and

wireless data networks and connect them to a corporate network. You will also receive

instruction on how to secure, diagnose and optimize communication networks. Certification

can also be offered to supplement almost all training courses.

Link: (https://www.siemens.com/industrial-networks-education)

Preface

CP 1628

8Operating Instructions, 06/2021, C79000-G8976-C280-09

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines, and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions form one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. These systems, machines and components should only be

connected to the enterprise network or the Internet if and only to the extent necessary and

with appropriate security measures (firewalls and/or network segmentation) in place.

You can find more information on protective measures in the area of industrial security by

visiting: (https://www.siemens.com/industrialsecurity).

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends performing product updates as soon as they are

available and using only the latest product versions. Use of product versions that are no

longer supported, and failure to apply latest updates may increase customer’s exposure to

cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under (https://www.siemens.com/industrialsecurity).

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.

You will find the SIMATIC NET glossary on the Internet at the following address:

Link: (https://support.automation.siemens.com/WW/view/en/50305045)

Recycling and disposal

The products are low in harmful substances, can be recycled and meet the requirements of

the Directive 2012/19/EU for disposal of waste electrical and electronic equipment (WEEE).

Do not dispose of the products at public disposal sites.

For environmentally compliant recycling and disposal of your electronic waste, please contact

a company certified for the disposal of electronic waste or your Siemens representative.

Note the different national regulations.

CP 1628

Operating Instructions, 06/2021, C79000-G8976-C280-09 9

Description of the device

Product features

NOTICE

Important information relating to the product

Some parts of the CP 1628 firmware are supplied by a third party. This third-party supplier

has informed us that they will no longer offer maintenance for the supplied software

components. This means that there is no monitoring regarding any future critical

vulnerabilities that may be exhibited by these software components. Siemens, therefore,

can no longer ensure that the firmware does not contain security-critical vulnerabilities for

all CP 1628 purchased after May 2021. Plus, any future security vulnerabilities can no longer

be published in a Security Advisory – due to the fact the Siemens no longer has any

knowledge of such vulnerabilities – and such vulnerabilities also are no longer removed.

However, the basic functionalities of the CP 1628 are not affected by these vulnerabilities.

The only difference is that there is no longer the full guarantee that the secure networks

used with the CP 1628 are fully protected. We therefore recommend that you implement a

state-of-the-art security concept for the entire plant (for more information, see the notes

under https://www.siemens.com/industrialsecurity). We especially recommend that you do

not secure the Internet access of the CP 1628 via the functions integrated into the product

but by using an additional security appliance, such as the SCALANCE SC. In this case, the

plant would be adequately protected even if there was a security-critical vulnerability in the

CP 1628.

The CP 1628 is a PCIe module for connecting PGs/PCs to Industrial Ethernet. The essential

properties are as follows:

•Two RJ-45 ports for Industrial Ethernet for connecting twisted-pair cables

•Can be used as a 2-port switch (both RJ45 connectors lead to the integrated switch)

•The following data rates are supported:

–10/100 Mbps (half/full duplex)

–1000 Mbps (full duplex)

•Own processor on the CP 1628 reduces the load on the PG/PC CPU.

•Autosensing, autocrossover, autonegotiation

•ISO and TCP/IP transport protocol onboard

Description of the device

CP 1628

10 Operating Instructions, 06/2021, C79000-G8976-C280-09

•Encrypted firmware that is signed and transferred to the CP 1628

•Integrated security (firewall, VPN)

Note

All CP 1613 and CP 1623 software products can be operated with the CP 1628.

Hardware requirements

The CP 1628 requires a PCIe slot (PCI express x1; can also be operated in x4, x8 or x16 slots).

LED display

The following graphic shows the front panel of the CP 1628 communications processor:

Connecting socket for optional external power supply

Port 1

Port 2

Power/fault LED

2 port LEDs for Port 1

2 port LEDs for Port 2

LEDs for displaying the transmission speed of Port 1 and Port 2

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens Synco RMK770 Manual de usuario

Siemens

Siemens LAL1.25 Manual de usuario

Siemens

Siemens SIMATIC ET 200S IM151-1 FO STANDARD Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SIRIUS 3RW44 Manual de usuario

Siemens

Siemens SENTRON PROFINET Proxy SPP2000 Manual de usuario

Siemens

Siemens 3WN 6 3WX3661-0JA00 Manual de usuario

Siemens

Siemens SIMATIC S7 3964 Manual de instrucciones

Siemens

Siemens SINAMICS G120 Hoja de datos

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens RMH760B Manual de usuario

Siemens

Siemens SIMOTION D4 Series Documento técnico

Siemens

Siemens SIMOTICS CONNECT 400 Manual de usuario

Siemens

Siemens SIRIUS ACT 3SU1401-2EE20-6AA0 Manual de usuario

Siemens

Siemens VAG61 Series Manual de usuario

Siemens

Siemens FCI1802-A2 Manual de usuario

Siemens

Siemens SINUMERIK 802D Guía de instalación

Siemens

Siemens XC1003-A Manual de instrucciones

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens MJ-5 Manual de usuario

Siemens

Siemens SINUMERIK 808D Manual de usuario

Siemens

Siemens ZIC-4A Manual de servicio

Siemens

Siemens SIMATIC NET Manual de usuario

Siemens

Siemens Flowrite VF 599 Series Manual del propietario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario