Siemens SIMATIC ET 200SP Manual de usuario

CM PtP communication module

(6ES7137-6AA00- 

0BA0)

_________________

____________

_____

_________________

SIMATIC

ET 200SP

CM PtP communication module

(6ES7137-6AA00-0BA0)

Manual

01/2013

A5E03790792-01

Preface

Documentation guide

Product overview

Connecting

Parameters/address space

Programming

Error and system messages

Technical specifications

Dimensional drawing

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E03790792-01

Ⓟ 01/2013 Technical data subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CM PtP communication module (6ES7137-6AA00-0BA0)

Manual, 01/2013, A5E03790792-01 3

Preface

Purpose of the documentation

This documentation provides important information on installing, wiring and commissioning

the ET 200SP point-to-point communications module.

This device manual complements the system manual ET 200SP distributed I/O system

(http://support.automation.siemens.com/WW/view/en/58649293). General functions of the

ET 200SP are described in the system manual ET 200SP distributed I/O system

(http://support.automation.siemens.com/WW/view/en/58649293).

Conventions

This documentation contains figures of the described device. The figures may differ slightly

from the devices supplied.

Please also observe notes marked as follows:

Note

A note contain important information on the product described in the documentation, on the

handling of the product and on the section of the documentation to which particular attention

should be paid.

Note on IT security

Siemens offers IT security mechanisms for its automation and drive product portfolio in order

to support the safe operation of the plant/machine. We recommend that you inform yourself

regularly on the IT security developments regarding your products. You can find information

on this on the Internet (http://support.automation.siemens.com).

You can register for a product-specific newsletter here.

For the safe operation of a plant/machine, however, it is also necessary to integrate the

automation components into an overall IT security concept for the entire plant/machine,

which corresponds to the state-of-the-art IT technology. You can find information on this on

the Internet (http://www.siemens.com/industrialsecurity).

Products used from other manufacturers should also be taken into account here.

Preface

CM PtP communication module (6ES7137-6AA00-0BA0)

4 Manual, 01/2013, A5E03790792-01

Open-source software is used in the firmware of the product described. The open-source

software is provided free of charge. We are liable for the product described, including the

open-source software contained in it, pursuant to the conditions applicable to the product.

Siemens accepts no liability for the use of the open source software over and above the

intended program sequence, or for any faults caused by modifications to the software.

For legal reasons, we are obliged to publish the original text of the following copyright

notices.

Permission to use, copy, modify, distribute and sell this software and its documentation for

any purpose is hereby granted without fee, provided that the above copyright notice appear

in all copies and that both that copyright notice and this permission notice appear in

supporting documentation. William E. Kempf makes no representations about the suitability

of this software for any purpose. It is provided "as is" without express or implied warranty.

Permission to use, copy, modify, distribute and sell this software and its documentation for

any purpose is hereby granted without fee, provided that the above copyright notice appear

in all copies and that both that copyright notice and this permission notice appear in

supporting documentation. Hewlett-Packard Company makes no representations about the

suitability of this software for any purpose. It is provided ``as is'' without express or implied

warranty.

CM PtP communication module (6ES7137-6AA00-0BA0)

Manual, 01/2013, A5E03790792-01 5

Table of contents

Preface ...................................................................................................................................................... 3

1 Documentation guide................................................................................................................................. 7

2 Product overview ....................................................................................................................................... 9

2.1 Properties.......................................................................................................................................9

2.2 Accessories..................................................................................................................................10

2.3 Functions......................................................................................................................................11

2.4 Properties of the interfaces..........................................................................................................13

2.4.1 Properties of the RS232 interface................................................................................................13

2.4.2 Properties of the RS422/485 interface.........................................................................................15

3 Connecting .............................................................................................................................................. 17

3.1 RS232 and RS422/485 interface of the communication module.................................................17

3.2 Installation guidelines...................................................................................................................18

4 Parameters/address space...................................................................................................................... 19

4.1 Parameter assignment.................................................................................................................19

4.2 Reaction to CPU STOP ...............................................................................................................19

4.3 Address space .............................................................................................................................20

5 Programming ........................................................................................................................................... 21

6 Error and system messages .................................................................................................................... 23

7 Technical specifications........................................................................................................................... 25

A Dimensional drawing ............................................................................................................................... 29

Table of contents

CM PtP communication module (6ES7137-6AA00-0BA0)

6 Manual, 01/2013, A5E03790792-01

CM PtP communication module (6ES7137-6AA00-0BA0)

Manual, 01/2013, A5E03790792-01 7

Documentation guide 1

Introduction

This modular documentation of the SIMATIC products covers diverse topics concerning your

automation system.

The complete documentation for the S7-1500 and ET 200SP automation systems consists of

system manuals, function manuals and manuals.

The STEP 7 information system (Online Help) also helps you configure and program your

automation system.

Overview of the documentation provided for the CM PtP communication module (ET 200SP)

The following table lists additional references that you will need when using the CM PtP

communication module.

Table 1- 1 Documentation for the CM PtP communication module

Topic Documentation Key content

System Manual S7 -1500 Automation System

(http://support.automation.siemens.com/WW/vi

ew/en/59191792)

System Manual ET 200SP distributed I/O

system

(http://support.automation.siemens.com/WW/vi

ew/en/58649293)

•Application planning

•Installation

•Connecting

•Addressing

•Commissioning

•Maintenance

Device manual Interface module

(http://support.automation.siemens.com/WW/vi

ew/en/55683316/133300)

•Connecting

•Interrupt, error and

system messages

•Technical specifications

•Dimensional drawing

System description

Function manual EMC/EMI compatible

installation of control systems

(http://support.automation.siemens.com/WW/vi

ew/en/59193566)

•Basics

•Electromagnetic

compatibility

•Lightning protection

Point-to-point

communication

Function manual CM PtP - Configurations for

point-to-point connections

(http://support.automation.siemens.com/WW/vi

ew/en/59057093)

•Basic information

•Data transmission

functions

•Diagnostics functions

Documentation guide

CM PtP communication module (6ES7137-6AA00-0BA0)

8 Manual, 01/2013, A5E03790792-01

SIMATIC Manuals

All current manuals for the SIMATIC products are available for download free of charge on

the Internet (http://www.siemens.com/automation/service&support).

CM PtP communication module (6ES7137-6AA00-0BA0)

Manual, 01/2013, A5E03790792-01 9

Product overview 2

2.1 Properties

Order number

6ES7137-6AA00-0BA0

View of the module

Figure 2-1 View of CM PtP (without BaseUnit)

Product overview

2.2 Accessories

CM PtP communication module (6ES7137-6AA00-0BA0)

10 Manual, 01/2013, A5E03790792-01

Properties

The communication module has the following properties:

● Technical properties

– RS232 interface (via BaseUnit)

– RS422/485 interface (via BaseUnit)

– short-circuit proof

– electrically disconnected

– Protocols: 3964(R), Modbus master (RTU), Modbus slave (RTU), Freeport and USS

with instructions

● Supported system functions

– Firmware update

– Identification data I&M0

– Parameter re-assignment in CPU RUN mode (using instructions)

– Diagnostic interrupts

Additional information

Additional information on the properties of the CM PtP can be found in the function manual

CM PtP - Configurations for point-to-point connections

(http://support.automation.siemens.com/WW/view/en/59057093).

You can find additional information on the design of the ET 200SP and the associated

modules in the system manual ET 200SP distributed I/O system

(http://support.automation.siemens.com/WW/view/en/58649293).

2.2 Accessories

ET 200SP accessories

Accessories and spare parts for ET 200SP can be found in the System Manual

ET 200SP

distributed I/O system (http://support.automation.siemens.com/WW/view/en/58649293).

Online catalog

Additional order numbers for ET 200SP can be found on the Internet

(http://www.siemens.com/industrymall) in the online catalog and online ordering system.

Otros manuales para SIMATIC ET 200SP

101

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SIWAREX FTC Guía de aplicación

Siemens

Siemens LOGO! CMR2020 Manual de usuario

Siemens

Siemens SIMOCODE pro 3UF7400-1AA00-0 Manual de usuario

Siemens

Siemens FDK:085U0321 Manual de usuario

Siemens

Siemens 3AH Manual de usuario

Siemens

Siemens Cm-lon 6BK1700-0BA10-0AA00 Manual de usuario

Siemens

Siemens XC10 Series Manual de instrucciones

Siemens

Siemens IONPURE VNX50HH-2 Manual

Siemens

Siemens SIMATIC S7 Manual de usuario

Siemens

Siemens Flowrite VF 599 Series Manual del propietario

Siemens

Siemens SINAMICS G120 Hoja de datos

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SINAMICS RAILCTRL Manual de lista de piezas

Siemens

Siemens P Series Manual de usuario

Siemens

Siemens EN100 Manual de usuario

Siemens

Siemens SIMATIC NET RX1500 Manual de usuario

Siemens

Siemens WFZ661 Manual de instalación y operación

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SINAMICS S120 Manual de lista de piezas

Siemens

Siemens SPCW110 Manual de usuario

Siemens

Siemens SIRIUS 3RT1.5 Manual de usuario

Siemens

Siemens 3RK1408-8K.00-0AA2 Manual de usuario

Siemens

Siemens Flowrite 599 Series Manual del propietario

Siemens

Siemens SIMATIC S5 1P 243 Documento técnico

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario