Siemens 7SC80 Manual de usuario

C53000-L2040-C353-3

SIPROTEC Compact

Feeder Protection

and Recloser Con-

troller 7SC80

Communication Module

DNP3 TCP

Bus Mapping/Point Lists

Preface

Contents

DNP3 TCP Device Profile 1

Point Lists 2

Flexible Mapping 3

Index

Disclaimer of Liability

This document has been subjected to rigorous technical review

before being published. It is revised at regular intervals, and any

modifications and amendments are included in the subsequent

issues. The content of this document has been compiled for

information purposes only. Although Siemens AG has made best

effortstokeepthedocumentaspreciseandup-to-dateaspossible,

Siemens AG shall not assume any liability for defects and damage

which result through use of the information contained herein.

This content does not form part of a contract or of business

relations; nor does it change these. All obligations of Siemens AG

are stated in the relevant contractual agreements.

Siemens AG reserves the right to revise this document from time to

time.

Document Release: C53000-L2040-C353-3.01

Edition: 09.2018

Product version: V1.05

The disclosure, duplication, distribution and editing of this

document, or utilization and communication of the content are not

permitted, unless authorized in writing. All rights, including rights

created by patent grant or registration of a utility model or a design,

are reserved.

Registered Trademarks

SIMATICTM, SIMATIC NETTM, SIPROTECTM, DIGSITM,

SICAMTM,SIMEASTM, SINAUTTM, OSCOPTM, and DAKONTM are

registered trademarks of SIEMENS AG. An unauthorized use is

illegal.

All other designations in this document can be trademarks whose

use by third parties for their own purposes can infringe the rights of

the owner.

NOTE

For your own safety, please observe the warnings and safety instructions contained in this document.

3SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Preface

Purpose of this manual

This manual describes the bus mapping of SIPROTEC 4 Communication Module with DNP3 TCP.

Target group

Protection engineers, commissioning engineers, persons who are involved in setting, testing and service of

protection, automation, and control devices, as well as operation personnel in electrical plants and power sta-

tions.

Scope of validity of this manual

This manual is valid for SIPROTEC 4 Communication Module with DNP3 TCP.

Further support

Should further information be desired or should particular problems arise which are not covered sufficiently for

the purchaser's purpose, the matter should be referred to the local Siemens representative.

Hotline

Our Customer Support Center provides around-the-clock support.

Phone: +49 (1805) 24-8437

Fax: +49 (1805) 24-2471

Internet: http://www.siprotec.com

e-mail: [email protected]

Training courses

If you are interested in our current training program, please contact our training center:

Siemens AG

Siemens Power Academy TD

Humboldtstr. 59

D-90459 Nuremberg

Germany

Phone: +49 (911) 433-7415

Fax: +49 (911) 433-5482

e-mail: poweracademy[email protected]

Internet: http://www.siemens.com/poweracademy

Preface

4 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Notes On Safety

Thismanual doesnotconstituteacomplete catalogof allsafetymeasures required for operating the equipment

(module, device) inquestion, because special operating conditionsmay require additionalmeasures.However,

it does contain notes that must be adhered to for your own personal safety and to avoid damage to property.

These notes are highlighted with a warning triangle and different keywords indicating different degrees of dan-

ger.

DANGER

DANGER means that death or severe injury will occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent death or severe injury.

WARNING

WARNING means that death or severe injury can occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent death or severe injury.

CAUTION

CAUTION means that minor or moderate injury can occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent minor injury.

NOTICE

NOTICE means that damage to property can occur if the appropriate safety measures are not taken.

✧Follow all advice instructions to prevent damage to property.

NOTE

It is important information about the product, the handling of the product, or the part of the documentation in

question to which special attention must be paid.

Preface

5SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Qualified Personnel

Commissioning and operation of the equipment (module, device) described in this manual must be performed

by qualified personnel only. As used in the safety notes contained in this manual, qualified personnel are those

persons who are authorized to commission, release, ground and tag devices, systems, and electrical circuits

in accordance with safety standards.

Use as Prescribed

The equipment (device, module) must not be used for any other purposes than those described in the

Catalog and the Technical Description. If it is used together with third-party devices and components, these

must be recommended or approved by Siemens.

Correct and safe operation of the product requires adequate transportation, storage, installation, and

mounting as well as appropriate use and maintenance.

During the operation of electrical equipment, it is unavoidable that certain parts of this equipment will carry dan-

gerous voltages. Severe injury or damage to property can occur if the appropriate measures are not taken:

• Before making any connections at all, ground the equipment at the PE terminal.

• Hazardous voltages can be present on all switching components connected to the power supply.

• Even after the supply voltage has been disconnected, hazardous voltages can still be present in the equip-

ment (capacitor storage).

• Equipment with current transformer circuits must not be operated while open.

• The limit values indicated in the manual or the operating instructions must not be exceeded; this also

refers to testing and commissioning

Preface

6 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

7SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1 DNP3 TCP Device Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 Data Objects Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.2 DNP3 TCP Device Profile Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 Point Lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.1 Binary Input Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.2 Control Relay Output Blocks/Binary Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.3 Counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.4 Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3 Flexible Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.1 Flexible Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Contents

8 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

9SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

1 DNP3 TCP Device Profile

1.1 Data Objects Implementation 10

1.2 DNP3 TCP Device Profile Documents 13

DNP3 TCP Device Profile

1.1 Data Objects Implementation

10 SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists

C53000-L2040-C353-3, Edition 09.2018

1.1 Data Objects Implementation

The following table identifies which object variations, function codes and qualifiers the DNP3 TCP implemen-

tation of the Feeder Protection and Recloser Controller 7SC80 will support in both request messages and in

response messages.

For static (non-change-event) objects, requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with

qualifiers 00 or 01.

Requests sent with qualifiers 17 or 28 will be responded with qualifiers 17 or 28.

For change-event objects, qualifiers 17 or 28 are always responded.

Note

Further information see in the SIPROTEC 4 document Communication Module DNP3 TCP - Communication

Profile, order number C53000-L2040-C354 or in Internet http://siemens.siprotec.de/download_neu/

index_e.htm.

Table 1-1 DNP3 TCP implementation table

Objects Request Response

Object

No. Var.

No. Description Function Codes

(dec) Qualifier Codes

(hex) Function Codes

(dec) Qualifier Codes

(hex)

1 0 Binary Input -

Any Variations 1 (read) 00, 01 (start-stop)

06 (no range)

07, 08 (limited qfy)

17, 28 (index)

1 2 Binary Input

with Status 1 (read) 00, 01 (start-stop)

06 (no range)

07, 08 (limited qfy)

17, 28 (index)

129 (response) 00, 01 (start-stop)

17, 28 (index)

2 0 Binary Input Change -

Any Variations 1 (read) 06 (no range, or all)

07, 08 (limited qfy)

2 2 Binary Input Change

with Time 1 (read) 06 (no range, or all)

07, 08 (limited qfy) 129 (response)

130 (unsol. resp) 17, 28 (index)

10 0 Binary Output -

Any Variations 1 (read) 00, 01 (start-stop)

06 (no range, or all)

07, 08 (limited qfy)

17, 28 (index)

10 2 Binary Output

with Status 1 (read) 00, 01 (start-stop)

06 (no range, or all)

07, 08 (limited qfy)

17, 28 (index)

129 (response) 00, 01 (start-stop)

17, 28 (index)

12 1 Control Relay Output

Block 3 (select)

4 (operate)

5 (direct op.)

6 (dir. op. noack)

17, 28 (index) 129 (response) echo of response

Otros manuales para 7SC80

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens VAI61 Series Manual de usuario

Siemens

Siemens VAG60 Series Manual de usuario

Siemens

Siemens SLT-1 Manual de usuario

Siemens

Siemens 3VL93 Series Manual de usuario

Siemens

Siemens VKF46 Series Manual de usuario

Siemens

Siemens 599-06611 Manual del propietario

Siemens

Siemens FM 458-1 DP Manual de usuario

Siemens

Siemens TC65 Manual de usuario

Siemens

Siemens CP 443-5 Extended Manual de usuario

Siemens

Siemens ECOFAST 3RK1911-4AB Series Manual de usuario

Siemens

Siemens SIMATIC ET 200eco PN Manual de usuario

Siemens

Siemens OCM-16 Manual de usuario

Siemens

Siemens Simatic TI405 Manual de usuario

Siemens

Siemens Flowrite 599 Series Manual del propietario

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Manual del propietario

Siemens

Siemens SINUMERIK 840D sl Hoja de instrucciones

Siemens

Siemens Siwarex U Guía de aplicación

Siemens

Siemens SIRIUS 3RT1.5 Manual de usuario

Siemens

Siemens HZM Manual de usuario

Siemens

Siemens TL-30U Manual de usuario

Siemens

Siemens Simatic S7-400 Manual de usuario

Siemens

Siemens MXG461B Series Manual del propietario

Siemens

Siemens VGD20.253U Manual del propietario

Siemens

Siemens FMT-A-ADPT Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario