Siemens SIMATIC NET CP 5614 A2 Manual de usuario

CP 5613 A2/CP 5614 A2

___________________

SIMATIC NET

PG/PC - PROFIBUS

CP 5613 A2/CP 5614 A2

Operating Instructions

08/2016

C79000

-G8976-C301-02

Preface

Description of the device

Software installation

Hardware installation

Configuration

Technical specifications

Certification

Siemens AG

Division Process Industries and Drive

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: C79000-G8976-C301

Ⓟ

09/2016 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 3

Table of contents

1 Preface ................................................................................................................................................... 5

2 Description of the device......................................................................................................................... 9

2.1 CP 5613 A2 product characteristics .........................................................................................9

2.2 CP 5614 A2 product characteristics .......................................................................................11

2.3 PROFIBUS interface...............................................................................................................12

2.4 Meaning of the LED display....................................................................................................13

3 Software installation.............................................................................................................................. 15

3.1 Installing the "SIMATIC NET PC Software"............................................................................15

3.2 Uninstalling the "SIMATIC NET PC Software"........................................................................16

4 Hardware installation............................................................................................................................. 17

4.1 Safety notices .........................................................................................................................17

4.2 Installing hardware..................................................................................................................18

4.2.1 Automatic adaptation of the bus clock speed .........................................................................18

4.2.2 Installing hardware PCI...........................................................................................................18

4.3 Hardware compatibility............................................................................................................19

4.3.1 Compatibility with other CPs...................................................................................................19

4.3.2 Replacement...........................................................................................................................19

5 Configuration ........................................................................................................................................ 21

6 Technical specifications ........................................................................................................................ 23

A Certification........................................................................................................................................... 27

Table of contents

CP 5613 A2/CP 5614 A2

4Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 5

Preface

What the consignment contains

The following components are supplied with the CP 5613 A2/CP 5614 A2:

●Communications processor CP 5613 A2/CP 5614 A2

●SIMATIC NET CD

●Certificate of license

Please check that the consignment you have received is complete. If the consignment is

incomplete, contact your supplier or your local Siemens office.

Validity of this documentation

These operating instructions are valid for the following products:

●CP 5613 A2

Article number: 6GK1 561-3AA01

●CP 5614 A2

Article number: 6GK1 561-4AA01

Content of this documentation

These operating instructions contain information about the installation and configuration of

the CP 5613 A2 and CP 5614 A2 communications processors.

Updated operating instructions on the Internet

You will find the current version of these operating instructions on the Product Support pages

under the following entry ID: 62612014

(https://support.industry.siemens.com/cs/ww/en/view/62612014)

Further documentation

The documents listed below contain more detailed information on commissioning and using

the communications processor. You will find this documentation on the Product Support

pages on the Internet under the following entry link:

Support (https://support.industry.siemens.com/cs/ww/en/ps)

Preface

CP 5613 A2/CP 5614 A2

6Operating Instructions, 08/2016, C79000-G8976-C301-02

Enter the entry ID shown below of the relevant manual as the search item.

●

Configuration manual Commissioning PC Stations

This provides you with detailed information on commissioning and configuring SIMATIC

NET PC communications modules.

Entry ID:

109488960 (https://support.industry.siemens.com/cs/ww/en/view/109488960)

●

System manual SIMATIC NET Industrial Communication with PG/PC

–

Volume 1– Basics

Entry ID:

77376110 (https://support.industry.siemens.com/cs/ww/en/view/77376110)

–

Volume 2– Interfaces

Entry ID:

77378184 (https://support.industry.siemens.com/cs/ww/en/view/77378184)

The system manuals introduce the topic of industrial communication and explain the

communications protocols used. There is also a description of the OPC interface as

user programming interface.

●

Installation manual "SIMATIC NET PC Software"

This document contains detailed information on installing the "SIMATIC NET

PC Software".

Entry ID:

77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602)

●

System manual PROFIBUS Network Manual

In this document you will find detailed information about setting up a PROFIBUS network.

Entry ID:

35222591 (https://support.industry.siemens.com/cs/ww/en/view/35222591)

SIMATIC NET documentation

You will find the entire SIMATIC NET documentation on the pages of Product Support:

15247 (https://support.industry.siemens.com/cs/ww/en/ps/15247)

Go to the required product group and make the following settings:

→Entry list →Entry type "Manuals / Operating Instructions"

Trademarks

The following and possibly other names not identified by the registered trademark sign ® are

registered trademarks of Siemens AG:

SIMATIC NET, HARDNET, SOFTNET, CP 1612, CP 1613, CP 5612, CP 5613, CP 5614,

CP 5622

Preface

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 7

Industry Online Support

In addition to the product documentation, the comprehensive online information platform of

Siemens Industry Online Support at the following Internet address:

(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=

en)

Apart from news, there you will also find:

●Project information: Manuals, FAQs, downloads, application examples etc.

●Contacts, Technical Forum

●The option submitting a support query:

(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid

=38718979&caller=view)

●Our service offer:

Right across our products and systems, we provide numerous services that support you

in every phase of the life of your machine or system - from planning and implementation

to commissioning, through to maintenance and modernization.

You will find contact data on the Internet at the following address:

(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)

SITRAIN - Training for Industry

The training offer includes more than 300 courses on basic topics, extended knowledge and

special knowledge as well as advanced training for individual sectors - available at more

than 130 locations. Courses can also be organized individually and held locally at your

location.

You will find detailed information on the training curriculum and how to contact our customer

consultants at the following Internet address:

(www.siemens.com/sitrain)

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.

You will find the SIMATIC NET glossary on the Internet at the following address:

50305045 (https://support.industry.siemens.com/cs/ww/en/view/50305045)

Preface

CP 5613 A2/CP 5614 A2

8Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2/CP 5614 A2

Operating Instructions, 08/2016, C79000-G8976-C301-02 9

Description of the device

2.1

CP 5613 A2 product characteristics

CP 5613 A2 characteristics

The CP 5613 A2 is a communications processor for connecting PCs to PROFIBUS. The

essential characteristics are as follows:

●The CP 5613 A2 is equipped with a PROFIBUS interface allowing up to 12 Mbps. It is

intended for operation in PGs and PCs with a PCI bus interface according to the PCI

standard V2.2.

●With the CP 5613 A2, up to 32 devices (PC, PG, SIMATIC S7 or ET 200) can be linked to

form a network segment. By linking several segments with repeaters, a maximum of 124

nodes can be connected.

●Optimized for fast DP master operation (DP Base) with up to 124 DP slaves with full data

consistency

●As an alternative, can also be used as a DP slave

●Relieves the PC due to event mechanisms (automatic detection of data changes)

●Fast logic support regardless of the user program (automatic linking of input and output

data can be set by the user program).

●Plug and play support during installation of the hardware

●Support of all data transmission speeds from 9.6 kbps to 12 Mbps

●Floating RS-485 connector

●Support of PCI 3.3 V/5 V, 33 MHz/66 MHz, 32 bit/64 bit and PCI-X 66 MHz, 32 bit/64 bit

Description of the device

2.1 CP 5613 A2 product characteristics

CP 5613 A2/CP 5614 A2

10 Operating Instructions, 08/2016, C79000-G8976-C301-02

CP 5613 A2 appearance

The following figure shows the CP 5613 A2 communications processor:

Yellow and green status LED

PROFIBUS interface 1 (master or slave)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de Siemens

Siemens

Siemens SMN42 Manual de usuario

Siemens

Siemens CP 5623 Manual de usuario

Siemens

Siemens SIMATIC NET CP 5622 Manual de usuario

Siemens

Siemens Simatic S7-300 CP 341 Manual de usuario

Siemens

Siemens SIMATIC S7-300 CPU Data: CPU 315-T-2 DP Manual de usuario

Siemens

Siemens DP/AS-Interface Link 20E Manual de usuario

Siemens

Siemens SIMATIC PCS 7 OSx Manual de usuario

Siemens

Siemens SIMATIC NET CP 5603 Manual de usuario

Siemens

Siemens CP 443-1 Manual de usuario

Siemens

Siemens SMP16-CPU06 Series Manual de usuario

Siemens

Siemens Simatic M7-400 Manual de usuario

Siemens

Siemens SIMATIC 317TF-2 DP Manual de usuario

Siemens

Siemens EB1 Manual de usuario

Siemens

Siemens Metro 21 M216KA Manual de usuario

Siemens

Siemens SED2 Series Manual de usuario

Siemens

Siemens TC35i Terminal Manual de usuario

Siemens

Siemens SIMATIC NET CP 243-1 IT Manual de usuario

Siemens

Siemens Fujitsu D1159 Manual de usuario

Siemens

Siemens SIMATIC S7 400 Guía del usuario

Siemens

Siemens LMV50 series Manual de usuario

Siemens

Siemens PAD-5-CLSA Manual de usuario

Siemens

Siemens SIMATIC S7-1200 Manual de usuario

Siemens

Siemens Gigaset PC Card 108 Manual de usuario

Siemens

Siemens CP 1243-8 IRC Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario