Siemens SIMATIC NET CP 5603 Manual de usuario

___________________

SIMATIC NET

PG/PC - PROFIBUS

CP 5603

Operating Instructions

08/2016

A5E02146341A

-04

Preface

Description of the device

Software installation

Hardware installation

Project engineering

Technical specifications

Approvals

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

Document order number: A5E02146341A

Ⓟ

09/2016 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CP 5603

Operating Instructions, 08/2016, A5E02146341A-04 3

Table of contents

1 Preface ................................................................................................................................................... 5

2 Description of the device......................................................................................................................... 9

2.1 Product characteristics..............................................................................................................9

2.2 PROFIBUS interface...............................................................................................................10

2.3 Meaning of the LED display....................................................................................................12

3 Software installation.............................................................................................................................. 13

3.1 Installing the "SIMATIC NET PC Software"............................................................................13

3.2 Uninstalling the "SIMATIC NET PC Software"........................................................................14

4 Hardware installation............................................................................................................................. 15

4.1 Safety notices .........................................................................................................................15

4.2 Installing hardware..................................................................................................................16

5 Project engineering ............................................................................................................................... 23

6 Technical specifications ........................................................................................................................ 25

6.1 Dimension drawings................................................................................................................27

A Approvals.............................................................................................................................................. 29

Table of contents

CP 5603

4Operating Instructions, 08/2016, A5E02146341A-04

CP 5603

Operating Instructions, 08/2016, A5E02146341A-04 5

Preface

Scope of delivery

Below, 5 delivery packages are introduced.

CP 5603 communications processor – 6GK1 560-3AA00

The following components ship with the product:

●Communications processor CP 5603 consisting of a PCI-104 basic module with an active

RS-485 module and 12-pin ribbon cable

●Installation fittings: To secure the CP 5603 basic module on the PCI-104 stack, 4 bolts

(M3, 15 mm) are supplied. To secure the RS-485 module in the expansion frame, 2

locking bolts are supplied (4-40 UNC, 8 mm).

●"SIMATIC NET PC Software" DVD

Installation kit CP 5603 for Microbox PC – 6GK1 560-3AA00-0AU0

The following components ship with the product:

●22 mm expansion frame for installation with a slot for the active RS-485 module

●Required installation fittings: 6 bolts (M3, 20 mm)

Installation kit CP 5603 for S7-mEC – 6GK1 560-3AA00-0AE0

The following components ship with the product:

●Shelf for installation with slots for the active RS-485 module

CP 5603 Microbox Package – 6GK1 560-3AU00

The following components ship with the product:

●Communications processor CP 5603 – 6GK1 560-3AA00

●Installation kit CP 5603 for Microbox PC – 6GK1 560-3AA00-0AU0

CP 5603 S7-mEC (modular Embedded Controller) Package – 6GK1 560-3AE00

The following components ship with the product:

●Communications processor CP 5603 – 6GK1 560-3AA00

●Installation kit CP 5603 for S7-mEC – 6GK1 560-3AA00-0AE0

Preface

0 Scope of delivery

CP 5603

6Operating Instructions, 08/2016, A5E02146341A-04

Validity of this documentation

These operating instructions are valid for the following product:

●CP 5603

Article number: 6GK1 560-3AA00

Content of this documentation

These operating instructions contain information about the installation and configuration of

the CP 5603 communications processor.

Updated operating instructions on the Internet

You will find the current version of these operating instructions on the Product Support pages

under the following entry ID: 62611947

(http://support.automation.siemens.com/WW/view/en/62611947)

Further documentation

The documents listed below contain more detailed information on commissioning and using

the communications processor. You will find this documentation on the Product Support

pages on the Internet under the following entry link:

Support (https://support.industry.siemens.com/cs/ww/en/ps)

Enter the entry ID shown below of the relevant manual as the search item.

●

Configuration manual Commissioning PC Stations

This provides you with detailed information on commissioning and configuring SIMATIC

NET PC communications modules.

Entry ID:

109488960 (https://support.industry.siemens.com/cs/ww/en/view/109488960)

●

System manual SIMATIC NET Industrial Communication with PG/PC

–

Volume 1– Basics

Entry ID:

77376110 (https://support.industry.siemens.com/cs/ww/en/view/77376110)

–

Volume 2– Interfaces

Entry ID:

77378184 (https://support.industry.siemens.com/cs/ww/en/view/77378184)

The system manuals introduce the topic of industrial communication and explain the

communications protocols used. There is also a description of the OPC interface as

user programming interface.

Preface

0 Scope of delivery

CP 5603

Operating Instructions, 08/2016, A5E02146341A-04 7

●

Installation manual "SIMATIC NET PC Software"

This document contains detailed information on installing the "SIMATIC NET

PC Software".

Entry ID:

109459606 (https://support.industry.siemens.com/cs/ww/en/view/77377602)

●

System manual PROFIBUS Network Manual

In this document you will find detailed information about setting up a PROFIBUS network.

Entry ID:

35222591 (https://support.industry.siemens.com/cs/ww/en/view/35222591)

SIMATIC NET documentation

You will find the entire SIMATIC NET documentation on the pages of Product Support:

15247 (https://support.industry.siemens.com/cs/ww/en/ps/15247)

Go to the required product group and make the following settings:

→Entry list → Entry type "Manuals / Operating Instructions"

Trademarks

The following and possibly other names not identified by the registered trademark sign ® are

registered trademarks of Siemens AG:

SIMATIC NET, HARDNET, SOFTNET, CP 1612, CP 1613, CP 5612, CP 5613, CP 5614,

CP 5622

Industry Online Support

In addition to the product documentation, the comprehensive online information platform of

Siemens Industry Online Support at the following Internet address:

(http://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo2&aktprim=99&lang=

en)

Apart from news, there you will also find:

●Project information: Manuals, FAQs, downloads, application examples etc.

●Contacts, Technical Forum

●The option submitting a support query:

(https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&lang=en&objid

=38718979&caller=view)

●Our service offer:

Right across our products and systems, we provide numerous services that support you

in every phase of the life of your machine or system - from planning and implementation

to commissioning, through to maintenance and modernization.

Preface

0 Scope of delivery

CP 5603

8Operating Instructions, 08/2016, A5E02146341A-04

You will find contact data on the Internet at the following address:

(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en)

SITRAIN - Training for Industry

The training offer includes more than 300 courses on basic topics, extended knowledge and

special knowledge as well as advanced training for individual sectors - available at more

than 130 locations. Courses can also be organized individually and held locally at your

location.

You will find detailed information on the training curriculum and how to contact our customer

consultants at the following Internet address:

(www.siemens.com/sitrain)

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.

You will find the SIMATIC NET glossary on the Internet at the following address:

50305045 (http://support.automation.siemens.com/WW/view/en/50305045)

CP 5603

Operating Instructions, 08/2016, A5E02146341A-04 9

Description of the device

2.1

Product characteristics

Properties

The CP 5603 communications processor has the following properties:

●PCI-104 interface

●Fast commissioning due to plug and play capability

●DP master operation (DP Base) with up to 124 DP slaves with full data consistency

●Relieves the PC due to event mechanisms (automatic detection of data changes)

●"Fast logic" support - automatic linking of input and output data can be set by the user

●Support of all data transmission speeds from 9.6 kbps to 12 Mbps according to the

PROFIBUS standard

●LED display

●Support of PCI-104 5V. (If the PCI signal voltage is 3.3 V, the host must provide a 5 V

power supply for the PCI-104 modules.)

●Floating active RS-485 connector with 12-pin ribbon cable

Description of the device

2.2 PROFIBUS interface

CP 5603

10 Operating Instructions, 08/2016, A5E02146341A-04

Representation

The following figure shows the CP 5603 communications processor with the active RS-485

module:

2.2

PROFIBUS interface

PROFIBUS network

The physical link between the PROFIBUS interface and the PROFIBUS network is via a

floating RS-485 interface that is part of the module. Depending on the network configuration,

data rates of 9.6 Kbps up to a maximum of 12 Mbps are possible in the PROFIBUS network.

Note

You will find information about the structure of a PROFIBUS network in the system manual

"PROFIBUS Network Manual". The document is part of the Manual

Collection. You will also

find this on the Product Support pages under the following entry ID:

Auto

-Hotspot

Otros manuales para SIMATIC NET CP 5603

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de Siemens

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SMP16-CPU06 Series Manual de usuario

Siemens

Siemens Metro 21 M216KA Manual de usuario

Siemens

Siemens CP 5613 A3 Manual de usuario

Siemens

Siemens SIMATIC NET CP 243-1 Manual de usuario

Siemens

Siemens SIMATIC S7-400 CP 440 Manual de usuario

Siemens

Siemens CP 5613 A3 Manual de usuario

Siemens

Siemens SIMATIC PG 760 Manual

Siemens

Siemens Fujitsu D1159 Manual de usuario

Siemens

Siemens SIMATIC NET CP 243-1 IT Manual de usuario

Siemens

Siemens CP 443-1 Manual de usuario

Siemens

Siemens CP 1243-8 IRC Manual de usuario

Siemens

Siemens SIMATIC CP 341 Manual de usuario

Siemens

Siemens SED2 Series Manual de usuario

Siemens

Siemens LMV50 series Manual de usuario

Siemens

Siemens Simatic 545-1106 Manual de usuario

Siemens

Siemens SIMATIC NET CP 1623 Manual de usuario

Siemens

Siemens SIMATIC S7-1200 CP 1243-8 IRC Manual de usuario

Siemens

Siemens SIMATIC CP 340 Manual de usuario

Siemens

Siemens 928B Guía del usuario

Siemens

Siemens SIMATIC 317TF-2 DP Manual de usuario

Siemens

Siemens TC65 Manual de usuario

Siemens

Siemens SIMATIC S7-1200 Manual de usuario

Siemens

Siemens CPU 31 Series Manual de instrucciones

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario