Shining 3D Einstart-c Manual de usuario

Einstart®-C User Manual

Add: NO.1398 XIANGBIN RD. WENYAN XIAOSHAN, HANGZHOU, 311258, CHINA Website：www.shining3d.com

www.3dker.cn

Einstart®-C

USER MANUAL

HANGZHOU SHINING3D TECH CO., LTD.

STOCK CODE：830978

Einstart®-C User Manual

CATALOG

1 Summary................................................................................................................................................. 1

1.1 How to use the User Manual......................................................................................................... 1

1.2 Attention........................................................................................................................................ 1

1.3 Product Model............................................................................................................................... 1

2 Product Introduction................................................................................................................................ 2

2.1 Product Appearance ..................................................................................................................... 2

2.2 Device parameters and accessories............................................................................................. 2

2.3 Sound illustration .......................................................................................................................... 2

3 Preparation.............................................................................................................................................. 3

3.1 Hardware Installation .................................................................................................................... 3

3.2 Software Installation and Serial Number Registration................................................................... 3

4 Using the Printer ..................................................................................................................................... 6

4.1 Slicing ........................................................................................................................................... 6

4.2 Print .............................................................................................................................................. 8

5 Software.................................................................................................................................................. 9

5.1 Adetailed look at the software interface........................................................................................ 9

5.2 Software functions ...................................................................................................................... 10

5.3 Advanced Parameters ................................................................................................................ 12

5.4 Introduction of LED Screen Button and Its Logic ........................................................................ 13

6 3Dker Platform（Website address：http://www.3dker.com/）.............................................................. 22

6.1 Model Downloading .................................................................................................................... 22

6.2 Software and Firmware Down loading. ....................................................................................... 22

7 Maintenance ......................................................................................................................................... 23

7.1 Printer Working Environment...................................................................................................... 23

7.2 Clean Up the Printing Environment............................................................................................. 23

7.3 Changing the Filament................................................................................................................ 23

7.4 Loading Filament ........................................................................................................................ 23

7.5 STL File....................................................................................................................................... 23

Einstart®-C User Manual

7.6 Set the Print Bed......................................................................................................................... 23

7.7 Sliding Rail.................................................................................................................................. 23

7.8 Consumable Parts List................................................................................................................ 23

8 FAQ....................................................................................................................................................... 24

8.1. The filament is blocked .............................................................................................................. 24

8.2. Extruder height adjustment........................................................................................................ 24

8.3. Model won’t stick to the platform................................................................................................ 24

8.4. Nozzle is surrounded by filament............................................................................................... 24

8.5. 3dStar software cannot connect to the 3D printer. ..................................................................... 25

8.6. Cannot read files on USB drive.................................................................................................. 25

8.7. The extruder is blocked, forming thin strands during printing or the model is dislocated. .......... 25

8.8. Limit switch malfunction............................................................................................................. 25

8.9 USB drive cannot be detected。................................................................................................. 25

Appendix：.............................................................................................................................................. 26

Einstart®-C User Manual

1 Summary

1.1 How to use the User Manual

This User Manual is set out to explain the following; Product Introduction, Preparation, How to Use the

Printer, Software Operation & Help, 3Dker Platform, Maintenance and FAQ. Please read the manual carefully

before use and follow instructions when using the Einstart-C.

1.2 Attention

Please consider the following information before using the printer.

1.2.1 Safety

The printer is only compatible with the power supply offered by Hangzhou Shining 3D Tech Co., Ltd.

Using an alternative power supply may lead to safety risks and/or damage to the printer

The print head reaches temperatures of over 200°C. To minimize potential risk, keep the printer door

closed during operation of the printer. It is also advisable to keep the printer door closed to reduce any outside

airflow, which can affect print quality.

DO NOT touch the model, print nozzle, print bed and any other part inside the printer until fully cooled to

room temperature. Care must be taken during the removal of 3D printed parts.

Although considered safe, the printer sends out small concentrations of vapor during printing therefore

good ventilation is recommended.

1.2.2 Protection

Keep the printer away from water as this may damage the printer.

DO NOT cut off power supply or unplug the USB cable during printing as it may cause print failure.

The printer operates at a room temperature of 5℃to 30 ℃. Print quality may be affected if the

temperature is not in this range.

Shining 3D has no responsibility for any damage caused to the printer through using print material or a

power supply not offered by Shining 3D.

1.3 Product Model

Einstart®-C Wifi International

Einstart®-C2 Wifi Domestic

Within this Manual, the model is noted as the Einstart®-C when describing common functions. Any notes

applying to the Einstart®-C2 will be made apparent.

Einstart®-C User Manual

2 Product Introduction

The Einstart®-C 3D printer is easy to operate and maintain. Its basic principle is that, upon digital input,

plastic is heated, melted and deposited to form the desired 3D model. The design is built up layer upon layer

with each successful layer turning solid to give a finished printed model that is sturdy and durable.

2.1 Product Appearance

Einstart®-C

2.2 Device parameters and accessories

See Appendix.

2.3 Sound illustration

The printer uses sound effects to give the user an indication of processes that are occurring e.g. Printer

start-up, filament loading etc.

Einstart®-C User Manual

3 Preparation

3.1 Hardware Installation

3.1.1 Remove the package

Unpack the inner and outer packaging and remove the cushioning foam. Use this manual and technical

drawings above to learn about accessories and set-up.

3.1.2 Print bed installation

Remove the print bed, open the printer door and fit it to the platform holder. Allow the magnet and

positioning block to cooperate and align with one another.

3.1.3 Install the Bowden Tube

Locate the transparent Bowden tube inside the printer and feed it through the central hole at the back of

the printer. Then insert it in to the extruder through the blue quick connector. The Bowden tube is easily

removed by pressing down on the quick connector and pulling the tube out.

3.1.4 Power Supply Connection

Start by connecting the adaptor to the cable plug. Once completed, insert the cable plug in to the mains

socket and connect the adaptor to the jack in the back right of the printer.

3.1.5 Turn On the Printer

Once the power supply is connected, press the switch on the right side of the printer to turn on. The LCD

screen display will indicate that the printer is turned on.

3.1.6 Filament Load

Remove the filament packaging and cut the end of the filament at an angle with pliers or scissors to create

a pointed tip. Place the filament reel on the filament holder located inside the printer on the right hand side.

Then feed the filament through the hole inside the printer and into the Bowden tube until it reaches the extruder.

Please refer to charter 5.4(11, 24, 25) for detailed operation.

Note: For better adhesion of the 3D print to the bed, we recommend a layer of masking tape or glue

stick on the print bed prior to print.

3.2 Software Installation and Serial Number Registration

The slicing software, 3dStar, supports several OS including WIN7 32bit/64bit, WIN8, WIN10 and Mac OS x.

The slicing software, serial port driver, serial number and selected model data can be found on the USB drive

provided. Please read the “Read Me” file and software user manual carefully before installing the software.

Einstart®-C User Manual

3.2.1 Software Installation and Registration for Windows OS.

3.2.1.1 Steps:

Open the file folder in the USB drive or download the installation software from our website. Find the

Setup.exe and run it. Click “Next” to enter the below interface and click “I Agree” after reading and accepting

the 3DPRINT END USER LICENSE AGREEMENT.

Choose the installation path you want by clicking “Browse” and click “Install”.

Upon Agreeing the license clause, click “Install” in the popup window. Complete the installation process by

Clicking “Finish”.

Einstart®-C User Manual

Note: If you’ve installed “Microsoft Visual C++ 2013”, just click “Repair” as below picture shows.

Install the FTDI CDM Drivers. Click “Extract” and operate according to the guidance given until installation

is complete.

Einstart®-C User Manual

4 Using the Printer

To obtain model data, please refer to charter 5.1 . There are also some 3D files available on the USB

drive provided.

4.1 Slicing

4.1.1 For slicing, open the 3dStar software and choose corresponding device model in “setting”,

“Application”. For this printer, you should choose E-c.

4.1.2 Choose the corresponding machine type. For this printer, you should choose E-C.Click the folder

icon to open and load an .stl file as the below picture demonstrates.

Einstart®-C User Manual

4.1.3 The 3dStar software allows users to view, move, rotate and scale their 3D model according to

requirements. To zoom in and out, use the scroll wheel on the mouse. To rotate around your model, left-click

and drag. To pan across your model, right-click and drag.

4.1.4 Click the settings icon on the top right of the screen to make any necessary adjustments to your 3D

model. See charter 5.1, 5.2 and 5.3 for detailed information on software and print settings. Click the generator

icon to generate path in .gsd format once you have confirmed your settings.

Otros manuales para einstart-c

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora 3D de Shining 3D

Shining 3D

Shining 3D einstart-c Manual de usuario

Shining 3D

Shining 3D einstart-c Manual de usuario

Shining 3D

Shining 3D AccuFab-L4D Manual de usuario

Shining 3D

Shining 3D AccuFab L4D Manual de usuario

Shining 3D

Shining 3D AccuFab-L4D Manual de usuario

Shining 3D

Shining 3D Transcan-C Manual de usuario

Shining 3D

Shining 3D AccuFab-D1s Manual de usuario

Shining 3D

Shining 3D Einstart Manual de usuario

Shining 3D

Shining 3D EinScan-SE Manual de usuario

Shining 3D

Shining 3D AccuFab-D1s Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario