SHAREBOT BIG Manual de usuario
BIG
QUICK START GUIDE
Version 21/02/2019
1
Your new Sharebot BIG
Safety Guidelines
Package Contents
Resin management:
Support
Working with Sharebot BIG
Configuration
Installation and use of slicing software
Using the printer interface
Dashboard
Managing files
LCD interface
LCD interface structure:
Network configuration
Procedure for network configuration
By connecting the Ethernet cable, DHCP automatically assigns an IP
address to the machine.
Wifi configuration
First print
Removing the printed object, finishing and postcuring process
Remove the resin from the resin tank and cleaning
Replacing the tank film
SHAREBOX 3D
Sharebot Cure
Cure installation:
Using Sharebot Cure:
Tips & Tricks
Printing plate calibration
Check the Fep status
Check before launch a new printing job the status of the FEP on the bottom of the
tank;
Z axis misalignment
Crack in models
Delaminations
Holes in model
Lines on printed models
Fitting problem
2
Only support printed
Sticky model
Vat leak
Warping
Support part missing
Your new Sharebot BIG
Sharebot BIG introduces a lot of new features in the resin 3d printer panorama:
● Pixel size 0,137mm;
● Resolution 4K 3840x2160px;
● Printing area 468x239 mm Z 340mm;
● Resin tank with Fep 100uM;
● Sw slicing Pyramis;
● 7’ lcd interface;
● Lan;
● Wifi;
● Door security switch;
● Dimension (W) x (D) x (H) 820 × 490 x 740 mm;
● Weight 66Kg;
We hereby declare that the product above is in compliance with the essential requirements
of the following:
Low Voltage (LV) Directive 2009/95/EC, 2014/35EU.
Electromagnetic Compatibility Directive(EMC), 2004/108/EC,2014/30/EU.
Restriction of the use of certain hazardous substances (RoHS) Directive, 2011/65/EU
Commission Regulation (EU) No. 453/2010 and IEC 60950-1 Safety of ITE
Technical Documentation is stored at the manufacturer’s address below.
Sharebot Srl
Via montello, 18
23895 Nibionno (LC)
Italy
3
Safety Guidelines
Read the instructions carefully. Keep this document for future reference. Follow all
warnings and instructions marked on the product.
● Operate on a table or flat, stable surface, ensuring that the machine cannot fall and
is level;
● Do not operate outdoors;
● Do not allow resin or any liquids to get inside the chassis, wipe up any liquid spills
immediately;
● Do not use solvents to clean the printer as they may damage the screen. Use a little
detergent and warm water to clean any resin spills;
● Disconnect the printer from the power before storage or when not used for a long
period of time. This 3D printer is connected to the electrical network with an input of
110 or 240 V AC, 50/60 Hz;
● Do not allow anything to rest on the power cord. Do not locate this product where
people will walk on the cord;
● If an extension cord is used with this product, make sure that the total ampere rating
of the equipment plugged into the extension cord does not exceed the extension
cord ampere rating. Also, make sure that the total rating of all products plugged into
the wall outlet does not exceed the fuse rating;
● Do not overload a power outlet, strip or receptacle by plugging in too many devices;
● Use the product only with the supplied power cable. If you need to replace the
power cable, make sure that the new power cable meets the following
requirements: detachable type, UL listed/CSA certified, VDE approved or its
equivalent, 4.5 meters (15 feet) maximum;
● In case of malfunction, disconnect the printer immediately from the power;
● Do not attempt to fix this product by yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all repairs to qualified
service personnel. Please send an email to your national supplier or contact
4
technical service at: [email protected]
● Keep the printer and resins out of the reach of children;
● Printer requires two people to lift it from the packaging;
● The resin is an irritant to skin and eyes. Always wear gloves when coming into
contact with the liquid resin. Always use in a well ventilated room;
● Resins are classified as irritants, not harmful, but in exceptional circumstances
people can be sensitive to the resin and develop a skin irritation or rash. Avoid this
possibility by always wearing gloves and avoid breathing fumes;
● The printer should be operated on a stable and level surface, preferably away from
direct ambient light;
Unplug this product from the wall outlet and refer servicing to a qualified service personnel
if:
● The power cord or plug is damaged, cut or frayed;
● Liquid has been spilled in the machine;
● The machine was exposed to rain or water;
● The machine has been dropped or the case has been damaged;
● The machine does not operate normally after following the operating instructions;
Package Contents
Fist of all, check that there are no damages to the machine and that all items listed below
are included in the package or in the Sharebot toolbox.
Your package should contain:
● A box with the Welcome Kit;
● 3D printer Sharebot BIG;
● Sharebot Cure;
● Ultrasonic cleaner;
Welcome Kit
The Welcome Kit contains:
● Print Plate;
● Resin Tank;
● Corner tank funnel;
● Scraper;
● Allen Key;
● Funnel;
● Paper Strainer;
● Nitrile Gloves;
● Print Sample;
● Tank Fep Film;
● Tank gasket;
● USB stick with Slicing Software and manuals;
● power and Rj45 cable;
● Oil pen for Z axis;
5
Test materials
A sample bottle of Sharebot D-Hard resin is provided with the 3d printer.
A sample of C-Cleaner;
Assembly instructions
1. Unscrew the screws on the top and front panels of the crate and place them to one
side;
2. Remove the polystyrene from around the printer;
3. Remove the resin bottle from the crate;
4. Unscrew the platform, remove and put it to one side. Lift the ancillary box out of the
printer (To unscrew the bolts lift them up to disengage the lock and turn the bolt to
loosen it. Repeat this step until the bolts are fully loose so the platform can be
removed.);
5. Place the platform back into the printer and tighten the bolts;
6. With two people lift the printer out of the crate holding the printer at the bottom and
top corner on both sides;
7. Place the printer on a flat and sturdy worktop ready for set-up;
8. Level the printer;
9. Calibrate the building plate:
Warning
• Make sure you have the building plate and the bottom of the tray perfectly clean, any
debris residues could compromise the calibration / printing or even damage the printer;
• Be sure to use protective gloves and goggles if you are calibrating the printer with
resin in the tray;
• Plate calibration must always be done before each print;
A. Insert the construction plane and lock it with the 2 knobs A;
B. Unscrew the 4 Allen screws B and secure the body in the middle of the
building plate;
C. From the printer menu, send the printer to Home;
D. When the plate is in position, apply a soft pressure with hands on the
building plate towards the bottom and tighten the 4 Allen screws B;
6
Resin management:
Sharebot Big 3D printer uses a resin management system that prevents the machine use
when the availability of material is less than the required to print the desired object. The
consumables management system works by decreasing the amount of resin used for
each print succeeded by the amount of resin available in the bottle currently in use.
At the time of insertion of a new resin code the available quantity of that resin comes
set to the amount available in the bottle.
The materials management guidelines are the following:
● Each resin bottle is associated with one and only one printer;
● When a new bottle is open, is necessary to generate the corresponding activation
code and insert it into the 3D printer where the material will use.
The procedure to add a material consists of the following steps:
● Access to the web interface (Sharebox) of the printer;
● Generation of the activation code;
● Entry of the activation code into the machine.
Access to the printer
The printer to which the material should be associated must be reachable via browser,
opened the address shown in the corresponding section "Configuration" and inserting the
credentials you be able to open the "Configure" section, select "Resin".
7
Generation of the activation code
Connect to the web site https://resine.sharebot.it/
The following login page will be displayed:
Warning: Check that the lock that indicates a secure communication is green.
Once the correct credentials have been entered and the "Login" button is pressed, the
activation code generation page is displayed:
8
Enter in the "Bottle code", the code shown on the resin bottle label
Enter in the "Printer Code", the code indicated in the "Configure" - "Resin" section of the
printer in which to activate the resin.
Warning: If you own a single machine, the "Printer Code" field will be automatically
compiled.
Pressing the "Send data" button will generate the activation code.
The generated code is valid only for the printer identified by the entered code.
9
Select the text of the gray area, copy it and paste it in the "Activation code" section of the
"Configure" - "Resin" section of the printer:
Once the "Save" button is pressed, the resin volume will be set to the contents of the
new bottle.
Fill in resin
Warning
● Make sure you have the building plate and the bottom of the tray perfectly clean,
any debris residues could compromise the calibration / printing or even damage the
10
Tabla de contenidos
Otros manuales de Impresora 3D de SHAREBOT
SHAREBOT
SHAREBOT Kiwi-3D Manual de usuario
SHAREBOT
SHAREBOT Kiwi-3D Manual de usuario
SHAREBOT
SHAREBOT Q Dual Manual de usuario
SHAREBOT
SHAREBOT 42 Manual de usuario
SHAREBOT
SHAREBOT VIKING Manual de usuario
SHAREBOT
SHAREBOT Next Generation XXL+ Manual de usuario
SHAREBOT
SHAREBOT Next Generation Manual de usuario
