SEWOO LK-P21 Manual de usuario
All specifications are subject to change without notice
J. STEPHEN Lab., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do, 18103, Korea
TEL : +82-31-8077-5000 FAX : +82-31-459-8880
www.miniprinter.com
USER’S MANUAL
MODEL : LK-P21
P21 Rev. D 02/18
For better safety and reliability, adhere to the following precautionary measures.
Read and follow the instructions carefully before operation of the product.
Safety Precautions
WARNING
Failure to follow these instructions could result in re, electric shock, other
injuries, or property damage.
Indication
Prohibition
(Potential risk of electric shock or re)
(Potential risk of electric shock or re)
(Potential risk of electric shock or re)
(Potential risk of electric shock or re)
Must follow
Do not disassemble Unplug the power from the
outlet
Grounding to prevent electric
shock
Do not handle the product
with wet hands
Do not pull or touch the power plug with
wet hands.
Do not bend the wire and do not allow the
wire to be pinched or crushed by heavy
objects.
If a power plug is broken or a plug is cut or
worn, do not use it.
Do not overload an electrical outlet.
WARNING
Failure to follow these instructions could result in re, electric shock, other
injuries, or property damage.
Failure to follow these instructions could result in re, electric shock,
other injuries, or property damage.
(Turn off the power using the power button)
(May cause damage or injury)
(Potential risk of re or unit malfunction)
(Potential risk of re or property damage)
(Potential risk of electric shock or damage)
(Potential risk of malfunction, electric shock,
or re. When the product needs to be repaired,
please contact your reseller)
Dealer
Do not unplug the power cable to turn off
the product.
Do not install the product on an unstable
or inclined surface.
If the product needs to be repaired,
please contact your reseller.
Avoid excessive shock or drops.
Keep product away from the water and
other material.
Do not disassemble, repair or modify the
product.
CAUTION
1
Table of Contents
1.
Unpacking
2
2.
Product Overview
3
3. Usage and Installation 4
3-1. Control Panel Usage 4
3-2. Battery Installation
5
3-3. Battery Removal
6
3-4. Battery Charging
7
3-5. Charging Cradle
8
3-6. Car Charger Usage
9
3-7. Belt Clip Usage
10
3-8. Paper Installation
11
3-9. Leather Case Usage
12
3-10. Self Test 13
3-11. MSR Usage
15
4. Peripheral Connection
16
4-1. Bluetooth Connectiontion 16
4-2. Interface cable Connection 17
5.
Printer Specification 18
6.
Certification 20
23
1. Unpacking
Standard
Option
Printer Battery
Serial Cable
Roll Paper
Belt Clip
USB Cable
Charger
CD Quick Manual
Battery Cradle Leather Case Shoulder Strap
CarAdapter
2. Product Overview
Paper Feed
Button
Open Button
Power
Switch
SERIAL
USB
Belt Clip
Hole Battery
DC Power
45
3. Usage and Installation
3-1 Control Panel Usage
Button
Name
function
Power
Button
This button is used to turn the printer on and off.
When the printer is off,press this button for approximately 3 seconds
and the printer will power on.When you press this button while the
printer is powered on, the printer will turn off.
Paper
Feed
Button
This button can be used to manually feed the paper.
Additionally, this button is also used to initiate self-tests and
Hexadecimal Dumping.
1. Refer to the Self Test section of this manual for information
regarding self-tests.
2. Refer to the Note in Self Test section of this manual for information
regarding Hexadecimal Dumping.
Battery
Status
Lamp
1. If the Batt LED is lit, the battery is fully charged.
2. If you can hear a beeping sound and LED light is turned off, the
battery is at the lowest level.
3. If the battery is not charged at all, the printer turns off
automatically.
Error
Lamp If the red light is turned on,
there is no paper or the paper cover is open.
1. Align battery hook as shown in the picture
2. Push the battery into the printer until it locks in place.
NOTE
As the battery is not charged at the time of your purchase, charge the
battery prior to using the printer
(Battery charger or Cradle can be used to charge)
Hook
3-2 Battery Installation
67
1
2
Rotate the Belt clip 180 degrees so it points upward.
After ipping the belt clip up, remove the battery as shown above.
180˚
3-3 Battery Removal
NOTE
1. If the charger provided by the manufacturer is not used,
the printer can be damaged, and the manufacturer is not liable for
the consequential damage.
2. Before removing the battery, make sure that power is turned o.
3. The printer does not work when only connected to the charger.
4. The battery needs to be installed to operate the printer.
5. While charging, do not turn on the power.
6. Do not operate the printer while charging the battery.
7. Do not connect the charger while the printer is operating.
1. Make sure the printer is turned o.
2. After opening the DC JACK cover, connect the DC JACK to the printer.
3. Plug the power cord into the electrical outlet.
3-4 Battery Charging
The charging status LED
Status charging charging complete
Charging Lamp Red
Green
89
3-5-1 The status of lamp in charging
lamp
Status charging charging complete
Charging Lamp Red
Green
NOTE
In the case the battery is not inserted properly, the red LED will blink.
Remove and reinsert the battery.
3-5 Charging Cradle
DC Jack
1. Insert the battery into the battery charger as shown above.
2. Connect the DC JACK to the electrical outlet.
3. Plug the power cord into the electrical outlet.
4. Once the charging is completed, remove the battery from the charger.
Optional
Input 12 ~ 24V
Output 8.4V 0.8 ~1.2A
Connect the car charger into the printer or battery cradle.
3-6 Car Charger Usage
Printer
Battery holder
NOTE
Only use the car charger included with the printer.
Optional
10 11
1
2
Tighten the screw with a screwdriver as shown in the picture above.
Insert the belt clip screw into the hole of the belt clip.
3-7 Belt Clip Usage
1 2
34
Press the PUSH button to open
the paper cover.
Pull a short length of paper out of
the printer and close the cover.
Insert the paper in the correct
direction. See the image above.
Tear o the additional paper using
tear bar.
3-8 Paper Installation
12 13
1 2
34
Open the leather case.
Close the cover and press down
on the Velcro.
Place the printer into the leather
case.
Fasten to the belt by using the clip
at the rear of the leather case.
3-9 Leather Case Usage
Optional
1 2
3
NOTE
Turn o the power by pressing the
power button for approximately
3 seconds.
The self-test will print.
While you are holding the FEED
button, press the power button.
3-10 Self Test
1. To print ASCII pattern additionally,
press the Feed button once more
2. After printing ASCII pattern, the
self test will be nished automatically.
3. If the Feed button is not pressed
to print ASCII pattern, the self-test will
automatically nish after 3 seconds.
Otros manuales para LK-P21
1
Tabla de contenidos
Otros manuales de Impresora de SEWOO
SEWOO
SEWOO LK-P30B Manual de usuario
SEWOO
SEWOO LK-B10 Manual de usuario
SEWOO
SEWOO LK-P30 Instrucciones de instalación
SEWOO
SEWOO LK-P30 Manual de usuario
SEWOO
SEWOO WTP-100 Manual de usuario
SEWOO
SEWOO LUKHAN LK-P21B Manual de usuario
SEWOO
SEWOO SLK-TE20 Series Manual de usuario
SEWOO
SEWOO LK-P31 Manual de usuario
SEWOO
SEWOO LK-P25 Manual de usuario
SEWOO
SEWOO SLK-TE21X Series Manual de usuario
SEWOO
SEWOO LK-T210 Manual de usuario
SEWOO
SEWOO SLK-TL100II Manual de usuario
SEWOO
SEWOO LK-T41 Manual de usuario
SEWOO
SEWOO LK-P30W Manual de usuario
SEWOO
SEWOO LK-P24 Guía de instalación
SEWOO
SEWOO SLK-TS400 Manual de instrucciones
SEWOO
SEWOO SLK-T12EB Manual de usuario
SEWOO
SEWOO SLK-T20EB Series Manual de usuario
SEWOO
SEWOO LK-P21 Manual de usuario
SEWOO
SEWOO LK-P25 Manual de usuario
