Senior Bad K55 Manual de usuario
Assembly Instructions Whirlpool Bath
K55 (07v20) eng
Attention:The pool should always be
be done by two people!
Senior
BadGmbH
2
Foreword
Dear customer, we are pleased that you have chosen this product. Please observe all
instructions before assembly and use and strictly follow the procedure below!
Please check the product for completeness rst. If there is any damage, please send us a
message with a short description and photos of the aected area. A responsible employee
will contact you as soon as possible and nd a solution together with you.
You have a 2-year legal warranty on all products.
Important information
Please note: The product is designed exclusively for private use. Our products are sub-
ject to constant further development. This may result in changes to the design and the
use of other components. We try to keep the following pages up to date. If you have any
questions regarding the design, please contact us at +49 35795 - 179 600 or by e-mail at
kundenservice@seniorbad.de. We are very grateful for any suggestions for improvement.
Please read the operating instructions carefully rst!
If you still have questions about the assembly, we will be happy to help you personally.
Complaints resulting from incorrect installation or use are excluded from the warranty!
Seals, hand showers, shower hoses and castors are wearing parts, therefore a warranty
period of 6 months applies here. The costs for replacement are not covered. Illuminants are
completely excluded from the warranty.
• Installation and assembly work should only be carried out by a skilled worker.
• Make sure that the bathtub is properly earthed. We recommend that any electrical
connections be made by trained professionals.
• The permissible water pressure should be approx. between 4 and 6 bar.
• From a hardness level of 10° (German hardness) we recommend the installation of a
softening device.
• Complaints based on limescale deposits are excluded from the warranty!
3
Sealing areas under/behind the bathtub
Sealing is compulsory - silicone is not enough!
The areas behind and under the bathtub must be tiled. Sealant joints - like silicone joints
- are not waterproong, but only maintenance and beauty joints! Only the use of bathtub
sealing tapes or e.g. sheet sealants comply with this DIN.
Waterproong according to DIN 18534
„This standard is therefore not only addressed to the waterproong specialist, but also to
those who are responsible for the overall planning and execution of the building and its
components, because the eect and durability of the waterproong depend on the coordi-
nated planning of all those involved.“
You as the installer are responsible for reliable waterproong alongside the planner and
tiler. „The waterproong must full its function for the intended service life with sucient
reliability.“
Waterproong must be planned so that it functions for the entire duration of use. In a
domestic bathroom, this can be an average of 20 to 25 years. In practice, this means laying
tiles or a membrane waterproong under the bath is mandatory. Note that the sealing area
at the transition from the oor to the wall must be at least 10 cm high.
Parameter
Rated voltage Frequency Total consumption Lighting
230V 50/60Hz 25W / with Whirlpool + 900W 10W
Fan Radio Frequency range Radio Whirlpool
5W 10W 88-108MHz 900W
The maximum water lling height is 34cm.
4
Please note:
1. The pool should be connected by an approved tradesman.
2. The pool should be assembled by a professional in accordance with these assembly
instructions. The power connection for the pool must be made by a certied electrician.
This person must also ensure sucient earthing to prevent accidents and malfunc-
tions.
3. Please have an electrician regularly check the function of the FI circuit breaker.
4. The statics of the oor must ensure that it can withstand the total weight of the pool
including water and one person.
5. The feet of the pool must stand on a rm, stable surface. The oor must be level.
6. Any damage found during unpacking must be reported immediately to the dealer, pref-
erably by taking photos and sending them to him.
Attention: This pool is not intended for permanent installation. It must be ensured that the
pool is installed in such a way that it is freely accessible for any maintenance or repair work.
Ensure that the bathroom oor is fully tiled and that there is a oor drain. The pool must not
be sunk into the oor!
Tools for the construction
Tools are not included in the package.
Check completeness!
Check that all the parts listed in the next section are complete. If you do not nd something
immediately, please look again carefully. Small parts in particular are easily overlooked due
to the large number of parts and the mass of the packaging.
Please do not dispose of the packaging until you are sure that it does not contain any small
parts.
Spirit level Drill/screwdriver Measuring tape Phillips / slotted
screwdriver
Open-end spanner
5
Product components
E
A Bath tub made of sanitary acrylic with removable apron/panel
B Right rear panel: The right rear panel is tted with the glass shelf.
C Shower panel: The panel is equipped with the back massage, the tting, the rain show-
er and optionally with the control display.
Please note that the shower panel has only been pre-assembled by the factory to
make it easier for you to assemble. It is absolutely necessary that you check all screw
connections and tighten them if necessary. This applies to the nozzles, the hoses on
the tting and the clamps.
DLeft rear panel *
*Please note that points B and D are reversed in the left-hand version.
A
BCD
Glass shelf
6
AB
16
B4
4x30
C
B5
x5
16
x6
4x30
x2
x1
C18
16
B4
4x30
Self-tapping
screw
Glass shelf Screw Nut Underlay
washer metal
Underlay Sili-
cone washer
Screw Upper arch
prole
Lower arch
prole
4a narrow
corner prole
4b wide corner
prole
Side window Flat gasket
2 x thick
Middle prole Screw Upper door
roller
Lower door
roller
Screw
Door seal,
F-seal
Glass door Screw Magnetic bar
7
Connections for water, sewage, electricity, telephone
Right version
1 Hot water 1/2 inch
2 Cold water 1/2 inch
Connections can also be on the
opposite side
3 Grey area = possible area for the
drain pipes, in the wall area the
drain can be up to a max. height of
6 cm to the centre of the hole
Drainage via exible connection
HT40 (supplied)
Connection possible without
dismantling the skirt/panel.
4 ATTENTION: leave the 15 cm Ø
around the white siphon (dark grey
area) under the drain free.
5a 230V 16A socket (or xed socket)
only for variant with radio, cable
length of transformer 1.20 m
5b 230V 16A (or xed socket) only for
version with whirlpool, cable length
of water pump 1.60 m
6Telephone connection
20 cm
10 cm
225 - 230 cm
115-125 cm
50 cm
25 cm
4 cm
10 cm
72 cm
42 cm
1
5a
5b
2
4
0-6 cm
6
3
8
Connections for water, sewage, electricity, telephone
Left version
1 Hot water 1/2 inch
2 Cold water 1/2 inch
Connections can also be on the
opposite side
3 Grey area = possible area for the
drain pipes, in the wall area the
drain can be up to a max. height of
6 cm to the centre of the hole
Drainage via exible connection
HT40 (supplied)
Connection possible without
dismantling the skirt/panel.
4 ATTENTION: leave the 15 cm Ø
around the white siphon (dark grey
area) under the drain free.
5a 230V 16A socket (or xed socket)
only for variant with radio, cable
length of transformer 1.20 m
5b 230V 16A (or xed socket) only for
version with whirlpool, cable length
of water pump 1.60 m
6Telephone connection
20 cm
10 cm
225 - 230 cm
115-125 cm
50 cm 25 cm
4 cm
10 cm
72 cm
42 cm
1
5a
5b
2
3
4
0-6 cm
6
9
Setting up and aligning the tub
Remove the skirt/panel and place the bathtub where you want it to stand later. Align it with
the help of a spirit level. Then pull the tub out approx. 40-50 cm from the corner. This is
necessary so that you can mount it on the back later.
You can adjust the height of the individual feet. It is very important that the tub stands
straight, does not tilt and that all feet are on the oor. It is also highly recommended that you
ll the nished tub with water and check that the water drains well. Please take some time
to do this.
TIP:
To make it easier for you to push the heavy tub into the corner after setting it up, we recom-
mend that you apply a lubricant to all feet. Then the tub will „glide“ better into the corner on
the tiles.
Mount shelf
TIP:
Mount the glass shelf on the back wall BEFORE
you place the back wall on the tub and screw it in
place.
Glass shelf
10
Screw back panels to panel and tray
The joint sealing tape (sponge rubber seal) supplied is glued to the two long corner proles
and to the panel (see diagram below).
Now place the left rear panel, then the panel and then the right rear panel on the tub. First
secure everything loosely with 1-2 screws and then align the assemblies in the slotted holes
and screw them together completely.
16 16
B4
88
Foam rubber seal
2-3 mm from the outer
edge, stick along the
panel.
Screw Nut Washer metal Silicone washer
Foam rubber
Foam rubber
Foam rubber
Foam rubber
Foam rubber
Foam rubber
Foam rubber
Tabla de contenidos
Otros manuales de Bañera de Senior Bad
Senior Bad
Senior Bad F01 Manual de usuario
Senior Bad
Senior Bad W20 Manual de usuario
Senior Bad
Senior Bad S12D Manual de usuario
Senior Bad
Senior Bad W02 Manual de usuario
Senior Bad
Senior Bad W23 Manual de usuario
Senior Bad
Senior Bad T18 Manual de usuario
Senior Bad
Senior Bad W60 Manual de usuario
Senior Bad
Senior Bad S17D Manual de usuario
Manuales populares de Bañera de otras marcas
Lyons
Lyons Elite ETLxx663219 Series Manual de usuario
Woodbridge
Woodbridge BJ500 Instrucciones de montaje
Whirlpool
Whirlpool Ariel ARL-702 Manual de usuario
TEIKO
TEIKO EXCELLENT DUO Manual de usuario
American Standard
American Standard Colony 5-1/2' x 32" Manual de usuario
American Standard
American Standard 3052OD.X0X Guía de inicio rápido
