Sealey PP5 Manual de usuario
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
PP5 Issue: 1 - 29/11/18
Original Language Version
© Jack Sealey Limited
Refer to instruction
manual
Wear eye
protection
INTEGRATED TEST LIGHT/VOLTMETER 3-48V
MODEL NO: PP5
1. SAFETY
WARNING! DO NOT use test light with domestic 110-230Volt supplies. Only use with DC Voltages between 3 and 48Volts.
9Observe standard workshop safety procedures when using the meter.
9Keep the work area clean, uncluttered and ensure there is adequate lighting. Keep tools and other items away from the engine and
ensure you can see the working parts of the engine clearly.
9 Maintaincorrectbalanceandfooting.Ensuretheoorisnotslipperyandwearnonslipshoes.
9 Removeillttingclothing.Removeties,watches,ringsandotherloosejewellery.Containortiebacklonghair.
9Ensure extension leads and probes are kept clear of hot surfaces and rotating parts.
8DO NOT drape cables around neck or arms – danger of entanglement.
8DO NOT disassemble meter.
8DO NOT get test light wet or use in damp or wet locations or areas where there is condensation.
8DO NOT use the meter for any purpose other than for which it is designed.
8DO NOT use the meter if damaged.
9When not in use place test in its case and store in a safe, dry, childproof location.
2. INTRODUCTION
LCD meter draws minute currents making this tool safe to use around delicate electronic components. With a range of 3-48V DC, this tool is
suitable for motorcycle, car and commercial applications. Includes interchangeable 65 & 175mm probes, leads and clips with Ø4mm banana
coupling.
3. OPERATION
3.1. To use the meter; connect the earth clip to a source of ground such as a ground wire, vehicle frame or the negative terminal of the
battery.
3.2. Fit the appropriate probe or clip to the meter and connect to the wire, socket etc. under test; the backlight on the LCD display will light
and the voltmeter will display any voltage present.
3.3. Ifnovoltageispresent,conrmthattheearthcliphasagoodground.
3.4. If the meter still does not operate check the lamp on a known good source such as a battery.
3.5. Havingconrmedthemeterisworkingcorrectly;testthewire,socketetc.undertestagain,ifyoustillhavenoreadingthewireisdead.
3.6. Consultthevehiclehandbookforfusepositionsandcheckifthefusehasblown.Ifthefusehasblown,rstestablishthereasonforthe
fuse blowing before replacing with the same fuse type.
3.7. Ifthefuseisgoodthenworkbackalongthetestwire,socketetc.towardsthefuseuntilyoundapointwhereitislive.Thiswayyou
can narrow down where the open circuit, break or bad connection is.
3.8. Note: You may use the probes to pierce the wire’s insulation to allow you to test closer to the open circuit, break or bad
connection.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
PP5 Issue: 1 - 29/11/18
Original Language Version
© Jack Sealey Limited
Tabla de contenidos
Otros manuales de Instrumento de medición de Sealey
Sealey
Sealey AK4565D.V2 Manual de usuario
Sealey
Sealey PP7 Manual de usuario
Sealey
Sealey AUTO SERVICE VS0563 Manual de usuario
Sealey
Sealey TA203.V2 Manual de usuario
Sealey
Sealey Auto Service VS8196.V2 Manual de usuario
Sealey
Sealey VS8113 Manual de usuario
Sealey
Sealey VAG VS862 Manual de usuario
Sealey
Sealey GA70CR Manual de usuario
Sealey
Sealey Auto Service Series Manual de usuario
Sealey
Sealey TA200.V2 Manual de usuario
Sealey
Sealey TA065 Manual de usuario
Sealey
Sealey AK9991 Manual de usuario
Sealey
Sealey TP101 Manual de usuario
Sealey
Sealey TA201 Manual de usuario
Sealey
Sealey MM405 Manual de usuario
Sealey
Sealey MM404 Manual de usuario
Sealey
Sealey MM302.V2 Manual de usuario
Sealey
Sealey DBG508 Manual de usuario
Sealey
Sealey TA200 Manual de usuario
Sealey
Sealey RS125.V2 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario