Sealey AK9623EV Manual de usuario

1 Internal Measure

2 Metric/Imperial Selector

3 Locking Screw

4 ABS/0 Switch

5 LCD Display

6 External Measure

7 On/Off Control

8 Zero Control

9 Battery Cover

10 Depth Measure

11 Step Measure

INSTRUCTIONS FOR:

MODEL:

AK9623EV

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND

CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO

MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.

DIGITAL VERNIER CALLIPER 0-300mm/0-12”

WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to

when using tools and equipment.

 DO NOT use if damaged.

 Maintain calliper in good and clean condition for best performance.

 Keep the work area clean, uncluttered and ensure there is adequate lighting.

Keep children and unauthorised persons away from the work area.

 DO NOT use the calliper for any purpose other than for which it is designed.

 DO NOT get calliper wet or use in damp or wet locations, or areas where there is condensation. Keep calliper clean

and dry using a dry cotton cloth only.

DO NOT dip or submerge the calliper in any type of liquid.

 DO NOT expose calliper to bright sunlight or dust.

 DO NOT disassemble. The calliper must be checked by qualified service personnel only.

 DO NOT apply any voltage to the calliper i.e. with an electric marker pen.

 The calliper is a precision instrument, treat with care, avoid using force and do not subject to knocks or shocks.

 Use in reasonably constant temperature conditions of approximately 20°C.

When not in use, turn off and store gauge in a safe, dry, childproof location.

Hardened and tempered stainless steel digital calliper with satin finish. 11mm High figures in LCD display for ease of reading.

Metric and Imperial calibration with conversion between the two. Zero setting control allows for comparative measurement.

Supplied in carry-case.

1. SAFETY INSTRUCTIONS

2. INTRODUCTION & SPECIFICATION

Resolution 0.01mm (0.0005”)

Range 0-300mm (0-12”)

Accuracy ±0.04mm/0.001”

Functions Zero set, mm/inch select, incremental zero

Messages Flashing display = replace battery

Battery life Approx. two years (approx. one year in continuous service)

Battery LR44 - 1.5V

Operational Temperature range 0 - 40°C

1234

7 8

AK9623EV Issue No: 1 - 24/09/08

1. Ensure all measuring surfaces are clean and then turn on calliper by pressing on/off control. Wait at least

one second before use.

2. Loosen locking screw and close the calliper; if read-out does not show zero when in closed position,

reset by pressing zero control.

3. Select inch or mm units, as required, with the metric/imperial selector. Check that display shows the

required units.

4. Measurements will now be shown directly on the LCD display.

5. A new zero may be obtained, at any open position of the calliper, by pressing the zero control.

6. A second measurement that then also needs to be added to the first one can be obtained by pressing the

ABS/0 switch after obtaining the first measurement (display will show ‘INC’), then move the callipers to

measure the second one. After noting this, press the ABS/0 switch again and the display will show the total

of both measurements.

A flashing display indicates that the battery is exhausted - replace as follows:

1. Switch off and then remove battery cover (9) by firmly sliding towards the right.

2. Remove exhausted battery and fit replacement with positive side uppermost (fig.1). Refit battery cover.

3. Dispose of old battery in a safe and approved manner. Do not burn.

If the display fails to alter when the slide is moved, remove the battery - wait at least 30 seconds and

then refit the battery.

fig.1

3. OPERATION

4. BATTERY FITTING

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

sales@sealey.co.uk

www.sealey.co.uk

Web

Environmental Protection.

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be

sorted, taken to a recycle centre and disposed of in a manner which is compatible with the environment.

When the product is no longer required, it must be disposed of in an environmentally protective way.

Do not incinerate battery as it may explode when exposed to fire.

Do not attempt to open battery.

Contact your local solid waste authority for recycling information.

AK9623EV Issue No: 1 - 24/09/08

Tabla de contenidos

Otros manuales de Instrumento de medición de Sealey

Sealey

Sealey DBG5010.V2 Manual de usuario

Sealey

Sealey TP67DT.V2 Manual de usuario

Sealey

Sealey AUTO SERVICE TA060 Manual de usuario

Sealey

Sealey TA090 Manual de usuario

Sealey

Sealey GA450 Manual de usuario

Sealey

Sealey GA70CR Manual de usuario

Sealey

Sealey TA500 Manual de usuario

Sealey

Sealey VSE9540 Manual de usuario

Sealey

Sealey MM302.V2 Manual de usuario

Sealey

Sealey AK9638D Manual de usuario

Sealey

Sealey AK9636D.V2 Manual de usuario

Sealey

Sealey TA050 Manual de usuario

Sealey

Sealey VAG VS862 Manual de usuario

Sealey

Sealey TA050 Manual de usuario

Sealey

Sealey VS0052.V2 Manual de usuario

Sealey

Sealey TA304 Manual de usuario

Sealey

Sealey AK9637D.V2 Manual de usuario

Sealey

Sealey AK9636D Manual de usuario

Sealey

Sealey 6-24V AUTO PROBE PLUS Manual de usuario

Sealey

Sealey Auto Service Series Manual de usuario

Sealey

Sealey TA070 Manual de usuario

Sealey

Sealey MM19.V3 Manual de usuario

Sealey

Sealey DBG506D Manual de usuario

Sealey

Sealey TA303 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario