Science Image FLOW 2 Manual de usuario
QUICK-START GUIDE
FLOW·2
1. FLOW·2 Inteace and Indicator
10 Headset / Mic
6Ethernet/POE 7DC 12V 8Facto Restore 9LINE IN
1/4 inch hole
11 USB / PTZ 12 Scroll Wheel Button 13 Power LED 14
5Optical TX/RX
1SDI input 2SDI output 3HDMI input 4HDMI output
- 01 -
2
1
8
7
910 11 12
3456
14
13
2. Power on and sta up
For FLOW 2, both DC input and POE power supply modes are available. When it stas up, the characters
‘ScienceImage Tech’ appear on the OLED screen, and the power lights on the right bottom of the FLOW 2.
Power on FLOW 2 with the SCIENCE IMAGE original
standard 12V power supply.
Please always use genuine SCIENCEIMAGE power
adapeters, third pay products may cause permanent
damage!
Power is supplied to the device by connecting a POE
(Power over Ethernet) Gigabit / 10 Gigabit network
switch.
Always use a ceied 802.11 af/at with a po
power capacity of at least 30W and a Gigabit network
switch.
2.1 DC 12V Input 2.2 POE Power over Ethernet (802,11af/at)
- 02 -
3. OLED Display and Scroll Wheel Button
In the power-up state, the current status and parameters displayed
on lines 1, 3 and 4 of the screen.
4K Converter
Optical Transmit
- 03 -
NOTE:
!
It takes about 30 seconds
from power up to normal
operation. Please be
patient.
1. The 1st line:
4K Conveer / Optical Transmit / Optical Receiver
Display device name and the status of the Optical Transceiver status.
The default is Optical Transmitting(or Receiving, the status can be
stored when power o).
2. The 2nd line:
Prima HDMI / SDI Selection
Show SDI or HDMI input priority.
3.
The 3rd line:
IN: 1080i50 / CH: SDI-Y HDMI-N
Display the input video format(when FLOW 2 at Optical Receiver,
the line shows format of the optical input);
Show whether the SDI and HDMI inputs are recognized, Y is detected,
N is no signal.
4.
The 4th line:
OUT: 2160p60 / 192.168.3.166
Display the user-selected output format for Up/Down conversion;
IP address
Scroll Wheel Button
Set FLOW 2 function: SDI/HDMI priority, output format, optical transceiver mode, SDI/HDMI input selection.
Operation method:
Press and hold the scroll wheel button for 3 seconds to enter the setup menu. Press “--Quit--” to exit.
- 04 -
Scroll down to ip down.
Setup Menu
Primary IN
>> Output Mode
Optical
Setup Menu
>> Primary IN
Output Mode
Optical
Scroll upward to ip up.
Setup Menu
Primary IN
>> Output Mode
Optical
Press down to conrm selection.
System Tools
Computer Management
Computer Management (Local)
Device Manager
4. Login Web UI
Open IE browser, type FLOW 2 IP address(OLED
screen), and enter the login page, as shown
below, Defualt User name and password are
the same: admin User name 用户名
admin
admin
Password 密码
Login 登录
- 05 -
NOTE:
!
The control PC or remote devices
needs to be in the same network
segment with FLOW 2.
Enter English
setting page
Enter Chinese
setting page
Method 1:
Login to the WebUI using USB RNDIS
function, power up the device and connect
tFLOW 2 to the computer with a USB cable.
Method 2:
>
A17D
>
Other devices
RNDIS
>
- 06 -
After the driver installation completed, open IE and enter ip address of FLOW 2:
192.168.88.8 and log in. Default username: admin Password: admin.
Use the following IP address:
IP address: 192 . 168 . 88 . 20
255 . 255 . 255 . 0
192 . 168 . 88 . 1
Subnet mask:
Default gateway:
If can't log in, you can change the IP address
of the new NDIS NIC in Network Connections
to 192.168.88.*, which is on the same
network segment as the device. IP address in
the same network segment as the device can
be used, please note that the device in the
LAN cannot use the same IP address.
NOTE:
!
Right-click RNDIS and select Update Driver -- browse my computer to nd a new driver -- select from the
list of drivers available on my computer -- Network Adapters -- Microsoft -- Remote NDIS compatible devices.
2
Common hardware types:
Update Drivers - RNDIS
Select your device’s type from the list below.
Network Seice
Next
Update Drivers - RNDIS
Select Network Seice
Microsoft
Microsoft NDIS Capture
Network Seice:
Next
5. Device information
Dashboard is FLOW 2 device information, contains the following information:
Device basic information, such as input HDMI source or SDI source, Video/Audio format, CPU temperature,
Memo usage and other parameters.
Dashboard
1
2
Device information includes:
Device name, Encoder/Decoder mode, Serial number, Hardware version, Firmware version, MAC address,
IP address, Local IP address, Disk space, etc.
2
1
- 07 -
- 08 -
6. Network settings
Click [Network] to enter the network setting page, where you can set the IP address. There are two modes:
automatic DHCP and manual.
Auto Manual
192.168.1.88
255.255.255.0
192.168.1.9
IP Address
Netmask
Gateway
Manual mode:
In manual mode, user can dene the FLOW 2 IP address freely and after that, FLOW 2 automatically
resta with new IP address.
DHCP:
In DHCP mode user do not need set IP address/Subnet Mask/Gateway, select Auto and click [Apply] below,
FLOW 2 will automatically reboot and get a new IP address assigned by the router.
Tabla de contenidos
Otros manuales de Convertidor de medios de Science Image
Science Image
Science Image NDI Studio 4K Manual de usuario
Science Image
Science Image NDI Studio 4K Manual de usuario
Science Image
Science Image NDI Studio 4K SH Manual de usuario
Science Image
Science Image NDI Studio 4K SH Manual de usuario
Science Image
Science Image NDI HD mini Manual de usuario
Science Image
Science Image FLOW 4K Manual de usuario
Science Image
Science Image NDI HD Manual de usuario
Science Image
Science Image NDI HD mini Manual de usuario
