SC&T VHE02EIP Manual de usuario
1
VGA/HDMI (HDBaseT) CAT5e Extender Series
ITEM NO.: VHE02EIP VGA/HDMI (HDBaseT) CAT5e Extender
VHE02EIP support HDMI up to 4K@60Hz YUV4:2:0 and VGA up to 1920 x 1200@60Hz,with HD
video/audio, bidirectional IR and RS-232, 2 way power over CAT5e/6 cable. It is an ideal
solution for extending PC/laptop to a display output to a projector/monitor application. With a
metal face plate at transmitter unit to provide installer a flexible installation to fit the TX unit at
wall or on a meeting table, which is a perfect application at video conference room.
VHE02EIP VGA/HDMI Auto Switch to HDBaseT Extender
With IR/RS232/PoH
To send and extend VGA/HDMI signal with IR/RS232/Power signal over one CAT5e
cable.
Auto switch or manually setting for VGA and HDMI inputs.
VGA support stereo audio convert to HDMI output, resolution up to
1920x1200@60Hz.
Transmission range up to 70M by CAT5e/6 cable.
Uncompression video transmission, HDMI resolution up to 4K@30Hz.
Support Bi-directional IR with 30-60 KHz, RS232, PoH, and CEC.
Max. Data Rate- 10.2Gbps.
HDMI 1.4 and HDCP compliance.
Audio support up to LPCM7.1@192Khz, Dolby TrueHD, DTS-HD MA.
Support PoH (Power over HDBaseT), allow power send either from TX or RX unit.
Built in power isolation.
Transmitter unit include metal wall plate mounting brackets for easy installation at
wall or on meeting table.
Installation view:
2
Panel View:
VHE02EIPT Front View Side View Dip Switch
VHE02EIPR Front View Rear View Dip Switch
LED Instruction:
Status
Color
VHE02EIPT
VHE02EIPR
POWER
GREEN
ON：Power on
ON：Power on
LINK
BLUE
ON：HDBaseT Linking
Flash: Power saving mode
ON：HDBaseT Linking
Flash: Power saving mode
HDMI
BLUE
ON：Select HDMI Input
VGA
BLUE
ON：Select VGA Input
IR
RED
Flash：IR Receiving or Sending
Flash：IR Receiving or Sending
3
Button Function:
FORCE SELECT
Function
Short Press
Manual Switch Mode: HDMI or VGA Input Selection
Long Press over 2
seconds
Auto Switch Mode: Auto Switch HDMI or VGA Input
Long Press: HDMI and VGA LED flash at same time that mean the
auto switch mode setting completed.
Under Auto Switch Mode: HDMI and VGA connect simultaneously,
VGA will be the priority.
Dip Switch Setting：
VHE02EIPT
Switch
Function
SW1
ON
Control Firmware
update
OFF
RS232 Extender
SW2
ON
Video Firmware
update
OFF
SW3
Reserve
SW4
Reserve
VHE02EIPR
Switch
Function
SW1
ON
Video Firmware
update
OFF
RS232 Extender
SW2
Reserve
Cable:
Link cable recommend use high quality Cat.5e、Cat.6、Cat.6a、Cat.7 UTP / STP or FTP
cable. Poor quality cable or network connection or improper construction will cause
unstable connection, video or sound disruptions, picture noise appears.
Distance chart by different cable:
Cable Type
Range
Supported Video
CAT5e / CAT6
60M
1080p 60Hz 12bit
CAT6a / CAT7
70M
CAT5e / CAT6
35M
1080p 60Hz 16bit
Up to 4096x2160@30Hz 4:4:4(9Gbps)
CAT6a / CAT7
40M
If connection through the wall socket, the cable length must less 5 meters between HDMI
extender and wall jack, as below drawing:
MAX 70 米
70M(Max)
VHE02EIPT
Wall Jack
VHE02EIPR
Wall Jack
5M
5M
4
RS232 Define:
DB9(F)/3.5mm STEREO PHONE JACK DB9(M)/3.5mm STEREO PHONE JACK
Power Saving Mode:
When there is no HDMI video signal input or TV is not connected or power off, this product
will enter a power saving mode to save power consumption; under a power saving mode
still provides, RS-232 (Less 9600bps), IR, and CEC signal transmission.
Caution:
1. The wiring must away from any equipment with electromagnetic wave, i.e.: mobile phone,
microwave, radio equipment, fluorescent lamp, high voltage power lines.
2. The cable must pull in straight to avoid any crosstalk interference and the transmission
Stability.
3. This device HDBaseT port is not general Ethernet signal; do not connect with Network
devices to avoid damage.
4. IR transmitter do not put near from receiver to avoid mutual interference.
RS232
3.5 mm Phone Jack
RS232
3.5 mm Phone Jack
Footprint
Define
Footprint
Define
Footprint
Define
Footprint
Define
Pin 2
RX
Pin 1
TX
Pin 2
TX
Pin 1
TX
Pin 3
TX
Pin 2
RX
Pin 3
RX
Pin 2
RX
Pin 5
GND
Pin 3
GND
Pin 5
GND
Pin 3
GND
DB9(F)/3.5mm STEREO PHONE JACK
DB9(M)/3.5mm STEREO PHONE JACK
5
VHE02EIP Package Include:
VHE02EIPT Transmitter x 1 pcs
VHE02EIPR Receiver x 1 pcs
DC24V/1.25Amp Power Adapter x 1 pcs
IR Emitter Cable x 1 pcs
IR Receiver Cable x 1 pcs
DB9(M)/3.5mm STEREO PHONE JACK x 1 pcs
DB9(F)/3.5mm STEREO PHONE JACK x 1 pcs
Metal Wall Plate x 1 pcs
Mounting Screw pack x 2 bags
Specification:
ITEM NO.
VHE02EIPT
VHE02EIPR
HDMI Interface
HDMI Type A
VGA Interface
VGA 15-Pin D-Sub
HDMI Video Support
Up to 1080p＠60Hz,48bits,3D
Up to 4096 x 2160@30Hz
VGA Video Support
Up to 1920 x 1200＠60Hz＠24bits
Audio Support
Up to LPCM 7.1 192Khz、Dolby TrueHD、DTS-HD MA
Analog Stereo Interface
3.5mm terminal x 1
HDBaseT Connector
RJ45 x 1
HDBaseT Distance
70M (Max)
IR Input /Output
3.5mm Phone Jack x 2
IR Carrier
Frequency/Angle/Distance
30~60KHz / T：± 10° / R：± 55° / 5M / Bi-directional
RS-232 Interface
DB9(F)/3.5mm STEREO
PHONE JACK
DB9(M)/3.5mm STEREO
PHONE JACK
RS-232 Data Rate
115200 bps / Duplex
Power Supply
DC 24 / 1.25A
Power Consumption
Max: 11.4W,Power Saving Mode: 1.8W
Temperature
Operation: 0 to 55℃, Storage: -20 to 85℃, Humidity: up to 95%
Dimension mm
86 x 93.5 x 42.8
92 x 69.5 x 25
Weight g
300
185
Rev. A
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Extensor de SC&T
SC&T
SC&T IP09P Manual de usuario
SC&T
SC&T HKM01-4K-KS Manual de usuario
SC&T
SC&T HE03-4K Manual de usuario
SC&T
SC&T VHE02EIP Manual de usuario
SC&T
SC&T VW01HA Manual de usuario
SC&T
SC&T CW01A Manual de usuario
SC&T
SC&T HKM02B-4K Manual de usuario
SC&T
SC&T IP05I Manual de usuario
SC&T
SC&T VKM03T Manual de usuario
SC&T
SC&T IP03PT Manual de usuario
SC&T
SC&T HD401F8-5M Manual de usuario
SC&T
SC&T DE01 Series Manual de usuario
SC&T
SC&T VKM04 Manual de usuario
SC&T
SC&T HKM02B-4K Manual de usuario
SC&T
SC&T IP01 Manual de usuario
SC&T
SC&T HE04SEK Manual de usuario
SC&T
SC&T HE01ERK Manual de usuario
SC&T
SC&T HE01SE Manual de usuario
SC&T
SC&T IP01 Manual de usuario
SC&T
SC&T IP09CK Manual de usuario
