SCAN Andersen 4 Manual de usuario
SCAN
Andersen 4
This manual is accompanied by a pamphlet
with General Iinstructions for Installation. Edition 10.04 - GB
INSTRUCTIONS FOR
INSTALLATION AND USE
Approved according to DIN 18891
You have chosen a product from one of Europe's leading manufacturers of wood-burning stoves. We are convin-
ced that your stove will be to your full satisfaction and give you many hours of pleasure if you follow the advice
and instructions of this manual.
Please read this manual as well as the General Instructions for Installation before beginning the installation.
Congratulations on your new SCAN Andersen-
stove!
Ceramic smoke deflectors
Clean combustion
The SCAN Andersen 4 uses the "CB techni-
que" (Clean-Burn) to ensure an optimally clean
combustion. The extra combustion air is pre-
heated and led into the combustion chamber
close to the ceramic smoke deflector.
Ceramic smoke deflectors
Follow the sketches below for the dismounting
of the ceramic smoke deflectors. Remove the
log guard (a). Lift the lower smoke deflector
plate, pull out the pins of the lateral firebricks,
and remove the plate. The upper smoke
deflector plate can be removed in the same
way.
a
Mounting of the heat shields
You have to mount separate heat-shields
under the SCAN Andersen 4. Place the stove
carefully on the back and mount the heat-
shields as shown on the sketch.
SCAN Andersen 4
Building-in
If the stove is to be built in, you must block the
four holes in the bottom, as the stove will other-
wise draw in false air.
Wood / briquettes Fuel kg/h (beechwood
max. 20% humidity)
SCAN Andersen 4 1,8 kg
Combustion air % 100
Primary air % 0-25
Adjustment of the air
1Ashtray. When you open the door, you have access to the ash-
tray, which is placed below the combustion chamber.
Attention! Be careful when you empty ashes from the stove.
There may be embers left for up to 24 hours after the stove
was last used.
2 Handle for shaking grate. The stove is equipped with a shaking
grate. When you activate the grate handle, the ashes from the
combustion chamber are emptied into the ashtray.
3Regulation for primary air. Turn the air valve in order to open.
The primary air is used when lighting and refuelling the stove. It
should always be closed during continuous firing.
4Regulation for combustion air. Push the button sideways. Left
position is closed and right position is open. The air is used for the
combustion and regulates the output of the stove.
The ashtray, shaking grate, and primary air should always be clo-
sed during continuous firing.
3
2
1
4
n
n
A
A
A
A
s
s
s
s
n
n
n
n
e
e
e
e
r
r
r
r
d
d
d
d
e
e
e
e
n
n
Handle
Your stove is equipped with a loose handle, which is
practical if you have small children. Put the handle
into the hole and turn it to open the door. If you want
a firm handle, you can mount the long screw that
you will find in the service bag.
Mounting of the convection
plates and the base
Place the stove carefully on the back and mount the
convection plates/base as shown on the sketch. The
screws and fittings are delivered together with the
convection plates/base.
Mounting of the soapstones
An instruction is delivered together with the soap-
stones.
SCAN Andersen 4
You should read this manual as well as the General Instructions for Installation before beginning the installation.
Krog Iversen & Co. A/S - DK-5492 Vissenbjerg
Technical info
Rated output: 6 W
Min./max.: 2 - 8 kW
Weight of radiation stove: 68 kg
Weight of convection stove: 94 kg
Weight of stove with curved steel mantle: 96 kg
Weight of stove with soap stones: 178 kg
Connection piece diameter: int. 120/ext. 128 mm
Warranty conditions
All SCAN wood-burning stoves and inserts are made of first-class material and are subject to a strict quality control befo-
re they leave the factory. However, if an error should occur, we back all SCAN wood-burning stoves and inserts with an
extensive, five-year limited warranty.
See also the General Instructions for Installation delivered with your stove for more details.
* To the middle of the
rear outlet (soapstone stove
630 mm)
* To the middle of
the rear outlet
Distances to flammable
materials (mm)
SCAN Andersen 4
Data for calculation of the chimney
Corner
Wall
Stove with convection sides
Stove with curved mantle
A
B
C
D
D
C
Radiation area
Radiation area
Base
plate
Base plate
You should observe the following minimum
distances from the sides of the stove:
A
B
C
D
SCAN A4
Convection stove
200
200
800
200
300
500
500
Stove
model
SCAN
Connecting
adaptor
mm
1
Density of
flue gas
flow
g/s
2
Flue gas
tempera-
ture
oC
3
Minimum
draft
Pa
4
Density of
flue gas
flow
g/s
5
Flue gas
temperature
oC
6
Minimum
draft
Pa
7
0,8
Minimum
draft
Pa
A4 130 - - - 6 340 11 9
With closed doorsWith open doors
Column 5 shows the flue gas temperature in the connecting adaptor
Column 6 shows the lowest/minimum draft in Pa by rated value
Column 7 shows the lowest/minimum draft in Pa by 0.8 x rated value
*
*
Otros manuales de Estufa de leña de SCAN
SCAN
SCAN 67 Guía del usuario
SCAN
SCAN 1006-B Guía del usuario
SCAN
SCAN Andersen 4-5 Manual de usuario
SCAN
SCAN 53 Guía del usuario
SCAN
SCAN 5005 FRL Guía del usuario
SCAN
SCAN 22 Manual de usuario
SCAN
SCAN 46 Manual de usuario
SCAN
SCAN 80 Guía del usuario
SCAN
SCAN 80 Manual de usuario
SCAN
SCAN ANDERSEN 8 Manual de usuario
SCAN
SCAN Andersen 1 Manual de usuario
SCAN
SCAN 3 Manual de usuario
SCAN
SCAN 47-2 Manual de usuario
SCAN
SCAN 65-1 Guía del usuario
SCAN
SCAN 1004-B Guía del usuario
SCAN
SCAN 37-2 Manual de usuario
SCAN
SCAN Scan 83-8 Guía del usuario
SCAN
SCAN 1005-B Guía del usuario
SCAN
SCAN Basic1 Manual de usuario
SCAN
SCAN 5-2 Manual de usuario
