Sauter SO 200K Manual de usuario

Sauter GmbH

Ziegelei 1

D-72336 Balingen

e-mail: info@kern-sohn.com

Phone : +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.sauter.eu

Instruction manual digital light meter

SAUTER SO 200K

Version 2.0

011/2020

SO-BA-e-2020

PROFESSIONAL MEASURING

2 SO-BA-e-2020

SAUTER SO 200K

V. 2.0 12/2021

Instruction manual digital light meter

Congratulations on purchasing this lighting knife from SAUTER. The purchase of this

device once again enables a step forward in the accuracy of measurement technology.

Although it is a complex and very sensitive instrument, it is still very robust and will last

you many years if used correctly. Please therefore read the operating instructions

carefully and keep them within easy reach.

We wish you much pleasure with your quality measuring instrument. For questions,

wishes or suggestions we are always at your disposal.

Table of contents

1General information....................................................................................... 3

2Functions........................................................................................................ 3

3Technical description.................................................................................... 3

4Function keys and part designation............................................................. 4

5Influencing variables of spectral sensitivity................................................ 5

6Steps to commissioning ............................................................................... 5

7Check and replace batteries ......................................................................... 5

8Maintenance................................................................................................... 5

9Examples of recommended illuminance levels........................................... 6

SO-BA-e-2020 SO-BA-e-20203

1 General information

This digital illuminance meter is a precision instrument for measuring illuminance in the

work area. The sensor has a full cosine correction for oblique light incidence. The

instrument is compact, robust and easy to use due to its design. The light-sensitive

component used in this light meter is a very stable, long-life silicon diode.

2 Functions

* The light measuring level ranges from 0.1Lux to

200,000 Lux, 0.01 FC (food candle) to 20,000 FC, in repetition

* High accuracy and fast response

* Peak-Hold function for recording peak values

* Unit and number display for easy reading

* Automatic zero setting

* Non-standard light sources are automatically

corrected

* Short rise and fall times

3 Technical description

Display: 3 ½ digit LCD

Measuring range: 200; 2,000; 20,000; 200,000 Lux

(20,000 Lux reading value x 10,

200,000 Lux reading value x 100)

20; 200; 2,000; 20,000 FC

(20,000 FC reading x 10)

1 FC= 10.76 Lux

Exceeded display range: Display of the highest

Digit "1" appears on the display

Accuracy: ± 3% rdg ± 0.5% f.s (± 5% rdg ± 10 dgt at >

20,000 Lux / 2,000 FC area).

Calibrated with a standard incandescent lamp at a colour temperature of 2856K

Repeatability: ± 2%.

Temperature Characteristic value: ± 1%/°C

Measuring rate: approximately 2.0 times/sec.

Photosensor: Silicon photo diode with filter

4 SO-BA-e-2020

Working temperature: 0°C to 40°C (32°F to 104°F)

Humidity at work: 0 to 70 RH

Storage temperature: -10°C to 50°C (14°F to 122°F)

Storage humidity: 0 to 80% RH

Power source: 1 x 9V block battery, 6F22

Lifetime with an alkaline battery (as a rule) 200h

Dimensions: 148mm x 70mm x 40mm

Photo sensor lead length: 1500mm (approx.)

Dimensions photo sensor: 100mm x 60mm x 28mm

weight: approx. 250g (5.8 oz)

Accessories: carrying case, operating instructions, battery

4 Function keys and part designation

1st LCD display: 3 ½ digits with maximum reading value until 1999.

2. on/off key: this key is used to switch the luxmeter on or off

3rd Data-PEAK key: Press this key to cancel the peak recording mode.

4th selection key: Press this key to change the selection of 200Lux/20FC;

2,000Lux/200FC; 20,000Lux/2,000FC; 200,000Lux/ 20,000FC (always repeating in a

circle).

5. data- hold key: this key is pressed to fix the current measured value. All further

measurements are stopped by the luxmeter. If the HOLD key is pressed again, this is

cancelled and the unit can take measurements again.

6. lux/FC unit key: Press this key to select between the Lux or Foodcandle (FC) unit.

7. photo sensor

SO-BA-e-2020 SO-BA-e-20205

5 Influencing variables of spectral sensitivity

As for the photo sensor: the photodiode with filters used almost reaches the C.I.E.

(International Commission on Illumination) standard of spectral sensitivity test

characteristics. The photo-optical curve V ( ) is shown in the table below:

6 Steps to commissioning

1. on/off button: The on/off button is used to switch the light meter on/off.

2. selection of the Lux/FC scale: Press this key to select the desired light metering

unit.

The photo sensor cover must first be removed and the photo sensor is then held

against the light source in a horizontal position.

The nominal illuminance value can now be read off the LCD display.

5. measuring range exceeded: If the unit only shows a "1" on the display, the input

signal was too strong and a higher range must be selected.

6. data HOLD mode: The HOLD key is pressed to enter the HOLD mode. The

luxmeter stops all further measurements. If this key is pressed again, this command is

cancelled and the instrument returns to normal operation.

7. data PEAK mode: Press the PEAK key to select the peak mode. Once this selection

is made, all subsequent measurements are paused. If the PEAK key is pressed again,

the PEAK-HOLD mode is cancelled and the instrument returns to normal operation.

After all measurements have been completed, replace the protective cap of the photo

sensor and press the off button.

7 Check and replace batteries

As soon as an adequate power supply is not ensured, the symbol appears on the LCD

display and a battery change with a 9V block battery is necessary.

2. switch off the unit to do this. The battery cover is pressed down and at the same

time pushed down in the direction of the arrow to open the battery compartment.

3. the battery is removed from the housing and replaced by a new 9V block battery

4. replace the battery cover.

8 Maintenance

6 SO-BA-e-2020

The white protective cap on the photo sensor should be wiped with a damp cloth from

time to time.

2. the light meter must not be stored at too high a temperature or humidity.

The period of time required for a calibration of the photo sensor varies with the working

operations. In general, the light sensitivity decreases directly proportional to the

product of the light intensity of the working time.

To maintain the general accuracy of the instrument, periodic calibration is

recommended.

9 Examples of recommended illuminance levels

Office

Conference/reception room 200-750

Office work 700-1500

Masch. writing, technical drawing 1000-2000

School

Lecture hall, gymnasium 100-300

Classroom 200-750

Laboratory, library, drawing room 500-1500

Hospital

Hospital room, storage 100-200

Room for medical examinations 300-750

Operating room 750-1500

Emergency room 750-1500

Factory

Packing work, goods receipt 150-300

Work on the assembly line 300-750

Visual inspection work 750-1500

Assembly of electronic parts 1500-3000

Hotel

lounge, cloakroom 100-200

Reception, cashier 220-1000

retail shop

Entrance stairs range 150-200

Shop windows, packing tables 750-1500

Front part of the shop window 1500-3000

SO-BA-e-2020 SO-BA-e-20207

Note:

When the protective cap is on the photosensor, the unit always displays "000";

if this is not the case, please operate the adjustable resistor on the back of the

housing.

Note:

To view the CE declaration, please click on the following link:

https://www.kern-sohn.com/shop/de/DOWNLOADS/

Tabla de contenidos

Otros manuales de Instrumento de medición de sauter

sauter

sauter TVL Manual de usuario

sauter

sauter CP P3 Manual de usuario

sauter

sauter CO Y5 Manual de usuario

sauter

sauter TVP Manual de usuario

sauter

sauter FC Manual de usuario

sauter

sauter SP 200K Manual de usuario

sauter

sauter FK 50 Manual de usuario

sauter

sauter TB Series Manual de usuario

sauter

sauter FA Manual de usuario

sauter

sauter TC 1250-0.1F Manual de usuario

sauter

sauter FL Manual de usuario

sauter

sauter TU-US Manual de usuario

sauter

sauter CT P1 Manual de instrucciones

sauter

sauter SN Manual de usuario

sauter

sauter TC 1250-0.1 F Manual de usuario

sauter

sauter TN-US Manual de usuario

sauter

sauter TB Manual de usuario

sauter

sauter SW 1000 Manual de usuario

sauter

sauter TVP-L Manual de usuario

sauter

sauter SU Manual de usuario

sauter

sauter JCS 100 Manual de usuario

sauter

sauter TF 1250-1.1FN Manual de usuario

sauter

sauter TN-US Manual de usuario

sauter

sauter SAUTER TE SERIES Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

sauter SO 200K Manual de usuario

Manuales populares de Instrumento de medición de otras marcas