Satel INT-TSG2 Manual de usuario

Otros manuales para INT-TSG2

4

Tabla de contenidos

Otros manuales de Teclado de Satel

Satel

Satel INT-KSG Guía del usuario

Satel

Satel INT-KWRL Manual de usuario

Satel

Satel Integra INT-KSG2R Manual de usuario

Satel

Satel INT-SF Manual de usuario

Satel

Satel VERSA INT-TSH2 Guía del usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Satel

Satel INT-KLCDK-GR Manual de usuario

Satel

Satel INT-SF Manual de usuario

Satel

Satel CR-MF5 Manual de usuario

Satel

Satel MKP-300 Manual de usuario

Satel

Satel INT-TSG Guía del usuario

Satel

Satel VERSA-LCDM-WRL Manual de usuario

Satel

Satel INT-TSG Manual de usuario

Satel

Satel VERSA-LCDM-WRL Manual de usuario

Satel

Satel PRF-LCD Manual de usuario

Satel

Satel INT-TSG Guía del usuario

Satel

Satel INT-KSG Manual de instrucciones

Satel

Satel INT-TSG2 Manual del propietario

Satel

Satel INT-SK-GR Manual de usuario

Satel

Satel INT-SCR Manual de usuario

Satel

Satel abax2 Manual de usuario

Satel

Satel VERSA INT-TSH2 Manual de usuario

Satel

Satel INT-TSG2 Manual de usuario

Satel

Satel INT-TSI Guía del usuario

Manuales populares de Teclado de otras marcas

BFT

BFT SELETTO Manual de usuario

Micro Id

Micro Id MP7G3BL Manual de instrucciones

WindowMaster

WindowMaster WLI 130 Manual de usuario

ACT

ACT ACT PRO 1030 Manual de usuario

Cardin

Cardin SSB Series Manual de usuario

Harman Kardon

Harman Kardon KP 1 Manual de usuario

Chamberlain

Chamberlain KPR2000 Guía del usuario

CYP

CYP CR-KP1 Manual de usuario

Aeware

Aeware k-35 Series Guía de referencia

Aritech

Aritech CS-175 Series Manual de usuario

GE

GE NetworX NX-1600E Series Manual de usuario

Lenze AC Tech

Lenze AC Tech MC SERIES Manual de usuario

Burg Wächter

Burg Wächter secuENTRY 7711 Manual de usuario

Aeware

Aeware in.k450 Manual de usuario

Lenze

Lenze EPM-H410 Manual de usuario

Toshiba

Toshiba RKP007Z Manual de usuario

Gemini

Gemini GEM-DXK1 KEYPAD Manual de usuario

Russound

Russound MDK-C5 Manual de funcionamiento

INT-TSG2

Keypad int-tsg2_sii_en 07/21

Quick installation guide

Full manual is available at www.satel.eu. Scan the QR code to go to

our website and download the manual.

The device should be installed by qualified personnel.

Changes, modifications or repairs not authorized by the manufacturer shall void

your rights under the warranty.

Disconnect power before making any electrical connections.

This is a Class A product. In a domestic environment this product may cause

radio frequency interference.

The keypad is designed for indoor installation. The place of installation should be readily

accessible to the system users.

1. Open the keypad enclosure (Fig. 1). The enclosure opening tool, shown in the illustration,

is included in the keypad delivery set.

2. Place the enclosure base on the wall and mark the location of mounting holes.

3. Drill the holes for wall plugs (screw anchors).

4. Run the wires through the opening in the enclosure base.

2 INT-TSG2 SATEL

5. Use wall plugs (screw anchors) and screws to fasten the enclosure base to the wall.

Select wall plugs specifically intended for the mounting surface (different for concrete or

brick wall, different for drywall, etc.).

6. Connect the DTM, CKM and COM keypad terminals to the appropriate terminals of the

control panel communication bus (Fig. 2). If you use the twisted-pair type of cable,

remember that CKM (clock) and DTM (data) must not be sent through one twisted-pair

cable.

The bus wires must be run in one cable.

The length of cables must not exceed 300 m.

7. If you wish to connect any detectors to the Z1 and Z2 zones, connect the wires to the

terminals (connect the detectors in the same way as to the control panel onboard zones).

8. Connect the supply wires to the KPD and COM terminals. The keypad can be powered

directly from the control panel, from an expander with power supply or from an additional

power supply unit.

9. Place the front panel onto the catches and snap close the enclosure.

10.Turn the power on, set the address and identify the keypad (see full installation manual).

Description of terminals

KPD - power supply input.

COM - common ground.

DTM - data.

CKM - clock.

Z1, Z2 - zones.

RSA, RSB - terminals provided for future applications (RS-485).

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu