Satel INT-SF Manual de usuario

Otros manuales para INT-SF

2

Tabla de contenidos

Otros manuales de Teclado de Satel

Satel

Satel INT-KWRL Manual de usuario

Satel

Satel INT-TSG2 Guía del usuario

Satel

Satel INT-TSG Manual de usuario

Satel

Satel INT-S Series Manual de usuario

Satel

Satel INT-TSG2 Manual de usuario

Satel

Satel INTEGRA INT-TSH2 Manual de usuario

Satel

Satel INT-KSG Manual de instrucciones

Satel

Satel INT-KSG Guía del usuario

Satel

Satel PRF-LCD Manual de usuario

Satel

Satel INT-SK Manual de usuario

Satel

Satel INT-SCR Manual de usuario

Satel

Satel INT-KWRL2 Manual de usuario

Satel

Satel CR-MF5 Manual de usuario

Satel

Satel INT-TSG2 Manual del propietario

Satel

Satel abax2 Manual de usuario

Satel

Satel INT-TS Manual de usuario

Satel

Satel CR-MF5 Manual de usuario

Satel

Satel INT-SK-GR Manual de usuario

Satel

Satel ABAX 2 Manual de usuario

Satel

Satel VERSA-LCDM-WRL Manual de usuario

Satel

Satel Integra INT-KSG2R Manual de usuario

Satel

Satel INT-TSH Manual de usuario

Satel

Satel MKP-300 Manual de usuario

Satel

Satel INT-S Manual de usuario

Manuales populares de Teclado de otras marcas

BFT

BFT SELETTO Manual de usuario

Micro Id

Micro Id MP7G3BL Manual de instrucciones

WindowMaster

WindowMaster WLI 130 Manual de usuario

ACT

ACT ACT PRO 1030 Manual de usuario

Cardin

Cardin SSB Series Manual de usuario

Harman Kardon

Harman Kardon KP 1 Manual de usuario

Chamberlain

Chamberlain KPR2000 Guía del usuario

CYP

CYP CR-KP1 Manual de usuario

Aeware

Aeware k-35 Series Guía de referencia

Aritech

Aritech CS-175 Series Manual de usuario

GE

GE NetworX NX-1600E Series Manual de usuario

Lenze AC Tech

Lenze AC Tech MC SERIES Manual de usuario

Burg Wächter

Burg Wächter secuENTRY 7711 Manual de usuario

Aeware

Aeware in.k450 Manual de usuario

Lenze

Lenze EPM-H410 Manual de usuario

Toshiba

Toshiba RKP007Z Manual de usuario

Gemini

Gemini GEM-DXK1 KEYPAD Manual de usuario

Russound

Russound MDK-C5 Manual de funcionamiento

INT-SF

Partition keypad int-sf_sii_en 07/20

Quick installation guide

Full manual is available on www.satel.eu

The device should be installed by qualified personnel.

Before installation, please read the full manual thoroughly.

Disconnect power before making any electrical connections.

The keypad is designed for indoor installation. The place of installation should be readily

accessible to the system users.

1. Open the keypad enclosure (Fig. 1). The enclosure opening tool, shown in the illustration,

is included in the keypad delivery set.

2. Set the partition keypad address (see “Address setting”).

3. Run the wires through the opening in the enclosure base.

4. Using wall plugs (anchors) and screws, fasten the enclosure base to the wall. Select wall

plugs specifically intended for the mounting surface (different for concrete or brick wall,

different for drywall, etc.).

5. Connect the CLK, DTA and COM terminals to the appropriate terminals of the control

panel expander bus (see the control panel installer manual).

2 INT-SF SATEL

6. If the partition keypad is to control an electric strike, electromagnetic lock or another door

actuator, connect this device to the NO terminals as shown in Fig. 2. It is not

recommended that the door actuator be powered from the same source as the partition

keypad.

7. If the keypad is to supervise the door status, connect the detector supervising the door

status to the IN and COM terminals. If the keypad is not to supervise the door status,

connect the IN terminal to the COM terminal or, when configuring the keypad, set value 0

for the “Max. door open time” parameter.

8. Connect the power wires to the 12V and COM terminals. The keypad may be powered

directly from the control panel, from an expander with power supply or from a power

supply.

9. Close the enclosure and then lock it with the screw.

10.Power on the alarm system.

11.Start the identification function in the control panel (see the control panel installer

manual). The keypad will be identified as "INT-S/SK".

Address setting

To set the address, use the DIP switches on the electronics board. The switches have

numbers assigned to them. The number for OFF position is 0. The numbers assigned to the

switches in ON position are presented in the table below. The sum of these numbers is the

address set.

Switch (ON position)

1 2 3 4 5

Number

1

2

4

8

16

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu