Sanus CFA16SM Manual de usuario
Customer Service
Americas: 800-359-5520 • 952-225-6013 • info@sanus.com
Europe, Middle East, and Africa: +31 (0) 495 580 852 • europe.sanus@milestone.com
Asia Pacic: 86 755 8996 9226 • sanus.ap@milestone.com
SANUS • 6436 City West Parkway • Eden Prairie, MN 55344 USA
©2012 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identication purposes and are trademarks of their respective owners.
sanus.com
We are here to help!
Please contact Customer Service with any questions.
CFA16SM
Instruction Manual
2
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Specifications
Weight-DO NOT EXCEED: 90.7 kg (200 lb.) includes rack and any components or accessories
CAUTION:
Avoid potential personal injuries and property damage!
Do not use this product for any purpose not explicitly specied by manufacturer
The wall must be capable of supporting ve times the weight of the rack and components or accessories combined
If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product,
contact Customer Service or call a qualied contractor
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
English
Required Tools
13mm
(1/2 in.)
5.5mm
(7/32 in.)
10mm
(3/8 in.)
3
Supplied Parts
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your
dealer; contact Customer Service. Never use damaged parts!
[01] x 2
[02] x 8 [03] x 8 [04] x 8
5/16 x 3½ in.
[05] x 4 [09] x 2
[08] x 4
[07] x 2
[06] x 2
4
Determine which conguration best
suits your needs. Attach the rack arm
of both swing arms [01] to the back
brace of the rack using carriage bolts
[02], washers [03], and lock nuts [04].
The swing arms [01] can be mounted
as a left hinged conguration or a right
hinged conguration.
Attach Swing Arm to Rack Assembly
[01]
Left Hinge
Right Hinge
[01]
[01]
[02]
[04]
[03]
[01]
5
1 2
Locate studs. Verify the center of the stud with an
awl or thin nail or use an edge to edge stud nder.
CAUTION: Avoid potential personal injuries
and property damage!
Any material covering the wall must not
exceed 16 mm (5/8 in.).
Minimum wood stud size: common 2 x 4 in
(nominal 1½ x 3½ in).
Mark the locations for the rst lag
bolts on the center line of the stud
measuring 578.4 mm (23⁄ in.)
apart for the CFR1615 and 809.6
mm (31⁄ in.) for the CFR1620.
CFR1615
578.4 mm
(23⁄ in.)
CFR1620
809.6 mm
(31⁄ in.)
41 cm
(16 in.)
Mounting to Wall (Wood stud)
6
3 4 Start hinge side lag bolts [05]. Leave
approximately 13 mm (1/2 in.) of
space from the bolt head to the wall.
Drill pilot holes as illustrated.
CAUTION: Improper use
could reduce the holding power
of the lag bolt. To avoid potential
injuries or property damage:
pilot holes MUST be drilled to a
depth of 89 mm (3½ in.), using a
5.5 mm (7/32 in.) diameter drill
bit.
89 mm
(3½in.)
5.5 mm
(7/32 in.)
[05]
[05]
13mm
(1/2 in.)
13 mm
(1/2 in.)
7
5Hang swing arm/rack assembly onto the lag
bolts [05].
[05]
[05]
[01]
[01]
8
7Tighten lag bolts [05] only until the washers [06]
are pulled rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.)
[01]
[01]
[05] [06]
6Slip "U" washers [06] onto the lag bolts [05].
[01]
[01]
[05]
[05]
[06]
[06]
9
8 9 Tighten lag bolts [05] only until the washers [07]
are pulled rmly against the wall arm [01].
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage DO NOT over-
tighten the lag bolts [05].
13mm
(1/2 in.)
Drill through the top slots of the wall arms [01]
into the center of the next stud.
CAUTION: Improper use could reduce the
holding power of the lag bolt. To avoid potential
injuries or property damage: pilot holes MUST be
drilled to a depth of 89 mm (3½ in.), using a 5.5
mm (7/32 in.) diameter drill bit.
89 mm
(3½in.)
[01]
[01]
[01]
[01]
[05]
[07]
5.5 mm
(7/32 in.)
10
1 2
406.6 mm
(16 in.)
CFR1615
578.4 mm
(23⁄ in.)
CFR1620
809.6 mm
(31⁄ in.)
Mark the locations for the lag bolts on the
corners of a rectangle measuring 406.4 (16 in.)
wide and 578.4 mm (23⁄ in.) for the CFR1615
and 809.6 mm (31⁄ in.) for the CFR1620 tall.
Drill pilot holes as illustrated.
CAUTION: To avoid potential injuries or
property damage:
Pilot holes MUST be drilled to adepth of 89 mm
(3½ in.) using a 10 mm (3/8 in.) diameter drill bit.
Never drill into the mortar between blocks.
Minimum solid concrete thickness: 8 in.
Minimum concrete block size: 8 x 8 x 16 in.
89 mm
(3½in.)
10 mm
(3/8 in.)
Mount to Wall (solid concrete or concrete block)
Tabla de contenidos
Idiomas:
Otros manuales de Rack y soporte de Sanus
Sanus
Sanus VUEPOINT F55 Manual de usuario
Sanus
Sanus VMF518 Manual de usuario
Sanus
Sanus OLF24-B2 Manual de usuario
Sanus
Sanus Secura QLL12 Manual de usuario
Sanus
Sanus VLL61 Manual de usuario
Sanus
Sanus CFR518RR Manual de usuario
Sanus
Sanus BXT3 Manual de usuario
Sanus
Sanus Sonos Beam WSSBM1-B2 Manual de usuario
Sanus
Sanus F215 Manual de usuario
Sanus
Sanus VTVS1 Manual de usuario
Sanus
Sanus WSECS1-B2 Manual de usuario
Sanus
Sanus VM300 Manual de usuario
Sanus
Sanus VisionMount ML11 Manual de usuario
Sanus
Sanus CFR1610 Manual de usuario
Sanus
Sanus SAN213 Manual de usuario
Sanus
Sanus VisionMount VMPR1 Manual de usuario
Sanus
Sanus VST4 Manual de usuario
Sanus
Sanus VLF510B1 Manual de usuario
Sanus
Sanus AMAZON ECHO SHOW 5 Manual de usuario
Sanus
Sanus WSSCAM1-B2 Manual de usuario
