Safe Fleet PRIME DESIGN VCC PC11 Manual de usuario

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: i[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

2

3

5

6

7

8

1

4

1

9

Stiff Channel 78” (2X)

10

Anti-Seize (1X)

Mounting Mid-Foot (2X)Mounting Foot (4X) Foam Pad (6X) Channel Bracket (4X) M8 x 20MM (6X) M6 X 25MM (10X)

" Lock Washer (6X) " Flat Washer (22X)

M8 Lock Nut (6X)Sealing Washer (10X)

VCC-PC11 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

CONTENTS OVERVIEW

2—Rear Crossbar Assembly.................................. (Qty 1)

3—Front Crossbar Assembly................................. (Qty 1)

1—FBM-0113 ........................................................ (Qty 1)

Channels with hardware

NOTE: This Manual contains Channels

and Hardware tting both two and three

Crossbar congurations.

If your model is a two Crossbar conguration,

disregard the extra Hardware contained in

the Channels and HKT-0166.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

3

VCC-PC11 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS

4—Handle Latch Assembly ................................... (Qty 2)

7—Quick Clamp Tube Splice Assembly ................ (Qty 2)

5.00“

9—HD Front Hook Assembly ................................. (Qty 2)

6—Clamp Down Tube ............................................ (Qty 2)

80.00”

8—Removeable Horn with Cap ............................. (Qty 2)

15.00”

5—Clamp Down Handle Assembly ....................... (Qty 2)

BLT-6846-M8 (1X)

11—Anti-Seize........................................................ (Qty 1)

10—USQSG-Ergorack ............................................ (Qty 1)

Quick Start Guide, Clamp Down

Anti-Seize (1X)

Once rack installation is complete, place the Quick Start Guide into

the vehicle’s glove box for future ladder setup and adjustment.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

4RIGHT SIDE ASSEMBLY SEQUENCE

3

4

2

5

1

6

7

M8 Lock Nut

Flat Washer

Rear

Front

T Bolt Stud

Rear

MPK-0093

Front

MPK-0092

Foam Pad

Mounting Bracket

M6 x 25MM Bolt

Sealing Washer

Flat Washer

VCC-PC11 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS

MOUNTING BRACKETS

1

CHANNELS

2.1 Apply Anti-Seize to all M8 T Bolt studs, then attach the

Channels to the Mounting Brackets using the indicated

hardware. Do not tighten until Step 2.2

Install the Channel Mounting Brackets into the vehicle’s

roof mounting holes and torque to 60 in-lb.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

5

Fig. A

Flush

Rear

Front

Fig. A

Rear

Front

Left

Right

M8 X 20MM

Lock Washer

Flat Washer

Left

Right

Rear

Front

Channel Rear Channel Front

(B) 72.00”

(A) 4.25”

VCC-PC11 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS

2.2

Position the Channel ends

until contacting the End

Caps as shown in Figure A.

Torque all Mounting Bracket

Nuts to 90 in-lb

2.4

Loosen nuts

Position the rear Mounting

Brackets as shown.

Position the front Mounting

Brackets as shown.

Attach Mounting Brackets to the Aluminum

Strip Nuts located in the Channels

2.3

2.6 Position Mounting Brackets to designated dimension shown

below, then torque the M8 X 20MM bolt to 90 in-lbs. Proceed

to Step 3.1.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

6

Rear

Front

Even Even

Front

Rear

VCC-PC11 ASSEMBLY INSTRUCTIONS–RIGHT SIDE CLAMP DOWN

CLAMP DOWN HANDLE CLAMP DOWN TUBE

4

5.2

5.1

5.3

Do not tighten

until Step 5.5

Torque to 90 in-lbs

NOTE: For instructional clarity, the FBM Mounting System will

not be shown for the remainder of this Assembly Manual.

CROSSBARS CROSSBAR ADJUSTMENT

3.1

Torque to

90 in-lbs

3.2

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

7

3

5

°

View from vehicle front

VCC-PC11 ASSEMBLY INSTRUCTIONS–RIGHT SIDE CLAMP DOWN

3.4 Set Clamp Down Horn

to angle shown.

5.5

Torque to 90 in-lbs

HANDLE LATCH

6.1

Do not tighten

until Step 6.3

6.3

Torque to 90 in-lbs

6.2 Position the Handle Latch until the

Handle Grip is rmly seated. FRONT LADDER HOOK

SEE QUICK START GUIDE FOR ADJUSTMENTS

7.2

Seat the Front Ladder Hook

into the lower Crossbar groove

as shown in this bottom view

7.1 Remove and retain the Front Ladder Hook

fastening hardware (not shown in this view)

for Steps 7.3 and 7.4

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

8

View from vehicle front

M8 Locknut

Flat Washer

M8 x 35MM

Carriage Bolt

VCC-PC11 ASSEMBLY INSTRUCTIONS–RIGHT SIDE CLAMP DOWN

7.6

Torque to 90 in-lbs

7.5 Adjust the Front Hook until it aligns with the Rear Hook. Perfect

alignment may not be possible in all instances, and depends

upon the location of the Crossbar Mounting Brackets. If such

interference should occur, align the Hook as close as possible.

NOTE: The orientation of

the bolt hole faces away

from the Crossbar

Place the Front Hook Clamp Bracket removed in Step 7.1

into the lower groove of the Crossbar, and slide it on top

of the Front Ladder Hook Clamp

7.3 7.4 Reassemble the Front Clamp Down Tube Holder

using the fastening hardware removed at Step

7.1. Do not tighten until Step 7.6

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

9

10

9

8

11

12

VCC-PC11 ASSEMBLY INSTRUCTIONS–LEFT SIDE CLAMP DOWN

LEFT SIDE ASSEMBLY SEQUENCE

CLAMP DOWN HANDLE CLAMP DOWN TUBE

8

9.1

9.2

9.3

Torque to 90 in-lbs

Do not tighten

until Step 9.5

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: 651-552-8554 ▪Toll Free: 1.8.PRIME.RACK ▪Fax: 651-552-1799 ▪Email: in[email protected] ▪Website: www.primedesign.net

TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

10

3

5

°

View from vehicle front

VCC-PC11 ASSEMBLY INSTRUCTIONS–LEFT SIDE CLAMP DOWN

9.4

Set Clamp Down Horn

to angle shown.

9.5

Torque to 90 in-lbs

HANDLE LATCH

10.1

Do not tighten

until Step 10.3

10.3

Torque to 90 in-lbs

10.2 Position the Handle Latch until the

Handle Grip is rmly seated. FRONT LADDER HOOK

SEE QUICK START GUIDE FOR ADJUSTMENTS

11.2

Seat the Front Ladder Hook

into the lower Crossbar groove

as shown in this bottom view

11.1 Remove and retain the Front Ladder Hook

fastening hardware (not shown in this view)

for Steps 11.3 and 11.4

Safe Fleet PRIME DESIGN VCC PC11 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas