Safe Fleet PRIME DESIGN ASH-8033 Manual de usuario

PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118

Toll Free: 1.8.PRIME.RACK ▪ Fax: 651-552-1799 ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability

(the “Prime Design Limited Warranty”).

▪

TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING

ASH-8033 PACKAGING CONTENTS

CONTENTS OVERVIEW

ASH-8033 Strobe/Go-Light Holder, Universal

Note: Rack model and Conduit

Carriers are shown in this Manual

for illustrative purposes only, and

are not included with this Light

Holder assembly.

M8 x 30MM (2X)

M8 x 70MM (2X)

M8 x 25 MM (2X)

M8 Lock Nut (4X) Lock Washer (2X)" Flat Washer (4X)

GoLight Mount (1X)Nut Bracket (2X) Z Post Clamp (1X) Mounting Clamp (1X)

Anti-Seize (1X)

(the “Prime Design Limited Warranty”).

▪

ASH-8033 ASSEMBLY INSTRUCTIONS

M8 x 70MM

GEN2/4 LIGHT HOLDER

INSTALLATION SEQUENCE

NOTE: Ladder Rack is shown for illustrative

purposes only, and is not included with this

Accessory Light Holder Kit.

This Light Holder Kit contains only the parts

needed to repair, replace, or retrot one

Crossbar. Order an additional kit for the other

Crossbar to add an additional accessory light.

1.2

Place the Light Holder Clamps into the

top groove of the Crossbar, ensuring the

Clamps seat into the Crossbar’s groove.

1.1 Assemble the Light Holder Clamps onto the

Crossbar using the provided hardware shown

below. Do not tighten until Step 1.5.

LIGHT HOLDER INSTALLATION 1.3 Place the Light Holder between the

Clamps, and ensure the Holder fully

engages the Clamp’s top groove.

1.4

Light Holder base must seat

in the Clamp’s upper groove.

Not all Gen2/4 racks will have enough space between

Rotation/Rotation Uppers to t a Light Holder. Measure

prior to installing to ensure there will be no rotation

Upper interference. A minimum of 10.00” is required

between the inside ends of Rotation/Rotation Uppers.

(the “Prime Design Limited Warranty”).

▪

Even Even

1.00”Figure 2

Figure 1

M8 x 30MM

If mounted to a Rotation/Rotation rack, center the Accessory

Light Holder evenly between the Uppers as seen in Figure 1.

If using on a rack equipped with only one rotation, mount a

minimum distance of 1.00” to prevent interference or binding

with the Rotation Upper as seen on Figure 2. Torque Light

Holder Clamp nuts to 90 in-lbs.

1.5 Attach the GoLight Holder to the Mounting Clamp

using the hardware shown and torque to 90 in-lbs.

1.6

ASH-8033 ASSEMBLY INSTRUCTIONS

NOTE: Ladder Rack shown is for illustrative

purposes only, and is not included with this

Accessory Light Holder Kit.

This Light Holder Kit contains only the parts

needed to repair, replace, or retrot one

Crossbar. Order an additional kit for the other

Crossbar to add an additional accessory light.

GEN5 LOW PROFILE LIGHT HOLDER

INSTALLATION SEQUENCE

Not all Gen5 racks will have enough space between

Rotation/Rotation Uppers to t a Light Holder. Measure

prior to installing to ensure there will be no rotation

Upper interference. A minimum of 10.00” is required

between the inside ends of Rotation/Rotation Uppers.

(the “Prime Design Limited Warranty”).

▪

Even Even

M8 x 25MM

M8 x 30MM

Center the Accessory Light Holder evenly between the Uppers

as seen below. Torque Strip Nut hardware to 90 in-lbs.

2.3 Attach the GoLight Holder to the Mounting Clamp

using the hardware shown and torque to 90 in-lbs.

2.4

2.1 Place the Nut Brackets into the Crossbar as shown.

LIGHT HOLDER INSTALLATION 2.2 Assemble the Light Holder Mount onto the Crossbar using the

hardware shown below. Torque nuts to 90 in-lbs.

ASH-8033 ASSEMBLY INSTRUCTIONS

(the “Prime Design Limited Warranty”).

▪

2345

GEN1LIGHT HOLDER

INSTALLATION SEQUENCE

NOTE: Ladder Rack is shown for illustrative

purposes only, and is not included with this

Accessory Light Holder Kit.

This Light Holder Kit contains only the parts

needed to repair, replace, or retrot one

Crossbar. Order an additional kit for the other

Crossbar to add an additional accessory light.

NOTE: Not all Gen1 Crossbars are factory drilled to

receive accessories. If not drilled, perform Steps 3.1 to

3.3. If factory drilled, proceed to Step 4.1.

Not all Gen1 racks will have enough space between

Rotation/Rotation Uppers to t a Light Holder. Measure

prior to installing to ensure there will be no rotation

Upper interference. A minimum of 10.00” is required

between the inside ends of Rotation/Rotation Uppers.

CROSSBAR PREPARATION-RETROFIT

Find the center of the top of the Crossbar between the inner

bends. Using a grease pencil and mark the center. Measure out

1.50” to the left and right of center, and mark using the grease

pencil. The marked distances will measure 3.00” across as

shown below.

3.1

Prior to drilling, mark a center line along the length of the

Crossbar to ensure the holes are correctly centered.

3.2

Drill holes using a

3/8” steel drill bit.

ASH-8033 ASSEMBLY INSTRUCTIONS

(the “Prime Design Limited Warranty”).

▪

M8 x 30MMM8 x 70MM

ASH-8033 ASSEMBLY INSTRUCTIONS

4.1 Assemble the Light Holder Mount onto the Crossbar using

the hardware shown below. Torque nuts to 90 in-lbs.

LIGHT HOLDER INSTALLATION 4.2 Attach the GoLight Holder to the Mounting Clamp

using the hardware shown and torque to 90 in-lbs.

(the “Prime Design Limited Warranty”).

▪

Varies

M8 x 35MM

Flat Washer

M8 Lock Nut

Fig. A

CONDUIT MOUNTING

5.1 Place the Strobe Holder onto the Conduit Carrier and

attach using the supplied hardware.

Torque to

70 in-lbs

5.3

5.2

The Strobe Holder can be positioned

anywhere between the Conduit Carrier

Mounting Clamp and Conduit Lock

Latch as shown below in Figure A.

ASH-8033 ASSEMBLY INSTRUCTIONS

NOTE: Conduit is shown for illustrative

purposes only, and is not included with this

Accessory Light Holder Kit.

This Light Holder Kit contains only the parts

needed to retrot one side. Order an additional

kit for the other side to add an additional

accessory light.

CONDUIT LIGHT HOLDER

INSTALLATION SEQUENCE

USAM-ASH8033-US01 Rev-B 0119

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Safe Fleet

Safe Fleet

Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual de usuario

Safe Fleet

Safe Fleet Rear View Safety RVS-350 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN masterack VRR CE Manual de usuario

Safe Fleet

Safe Fleet Rear View Safety RVS-778718N Manual de usuario

Safe Fleet

Safe Fleet Prime Design AR1303-S Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN HRR-269-E-UM3-80 Manual de usuario

Safe Fleet

Safe Fleet Prime Design FBM-1026-BLK Manual de usuario

Safe Fleet

Safe Fleet Prime Design CSM-1001 Series Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN VCC NV11B Manual de usuario

Safe Fleet

Safe Fleet Prime Design HRI3-E-FT32B Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN HRR-269-E-UM3-96 Manual de usuario

Safe Fleet

Safe Fleet Prime Design VRR-FT31G-ST Manual de usuario

Safe Fleet

Safe Fleet Prime Design PBC 6000 Manual de usuario

Safe Fleet

Safe Fleet RVS-619NQ Manual de usuario

Safe Fleet

Safe Fleet Prime Design VBC NV200 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN VCR3-FT31B Manual de usuario

Safe Fleet

Safe Fleet Prime Design VRR NV200 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN VRR-NV200 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN HBR-E FT22B Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN HRR-E-PM42 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN VBR-NV200 Manual de usuario

Safe Fleet

Safe Fleet PRIME DESIGN HBI-E-FT33B Manual de usuario

Safe Fleet

Safe Fleet Prime Design FEA0002 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario