Ruijie RG-S29 Series Manual de instalación

RG-S29 Series Switch

RGOS Command Reference, Release 11.4(1)B12

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,

transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,

without the prior written consent of Ruijie Networks is prohibited.

Exemption Statement

This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain

the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will

not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual matches the RGOS Release 11.4(1)B12.

Audience

This manual is intended for:

Network engineers

Technical support and servicing engineers

Network administrators

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: http://caseportal.ruijienetworks.com

Community: http://community.ruijienetworks.com

Technical Support Email: s[email protected]

Skype: [email protected]

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Hardware Installation and Reference

Guide

Describes the functional and physical features and provides the device

installation steps, hardware troubleshooting, module technical specifications,

and specifications and usage guidelines for cables and connectors.

Conventions

This manual uses the following conventions:

Convention

Description

boldface font

Commands, command options, and keywords are in boldface.

italic font

Arguments for which you supply values are in italics.

[ ]

Elements in square brackets are optional.

{ x | y | z }

Alternative keywords are grouped in braces and separated by vertical bars.

[ x | y | z ]

Optional alternative keywords are grouped in brackets and separated by

vertical bars.

Symbols

Means reader take note. Notes contain helpful suggestions or references.

Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of

data.

System Configuration Commands

1. Command Line Interface Commands

2. Basic Configuration Management Commands

3. Line Commands

4. File System Commands

5. SYS Commands

6. Time Range Commands

7. HTTP Service Commands

8. Syslog Commands

9. CWMP Commands

10.CA-MONITOR Commands

11.ZAM Commands

12.Module Hot-plugging/Unplugging Commands

13.Supervisor Module Redundancy Commands

14.PoE Management Commands

15.PKG-MGMT Command

Command Reference Command Line Interface Commands

1 Command Line Interface Commands

1.1 alias

Use this command to configure a command alias in global configuration mode. Use the no or default

form of this command to restore the default setting.

alias mode command-alias original-command

no alias mode command-alias

default alias mode [command-alias]

Parameter

Description

Parameter

Description

mode

Mode of the command represented by the alias

command-alias

Command alias

original-command

Syntax of the command represented by the alias

Defaults

Some commands in user or privileged EXEC mode have default alias.

Command

Mode

Global configuration mode.

Usage Guide

The following table lists the default alias of the commands in privileged EXEC mode.

Alias

Actual Command

help

ping

show

undebug

The default alias cannot be removed by the no alias exec command.

After configuring the alias, you can use a word to replace a command. For example, you can create

an alias to represent the first part of a command, and then type the rest part of the command.

The mode of the command represented by the alias is the command mode existing in the current

system. In the global configuration mode, you can use the alias ? command to list all the modes

under which you can configure alias for commands.

Ruijie(config)# alias ?

aaa-gs AAA server group mode

acl acl configure mode

config globle configure mode

......

Command Reference Command Line Interface Commands

The alias also has its help information that is displayed after * in the following format:

*command-alias=original-command

For example, in the privileged EXEC mode, the default alias s stands for show. You can enter s? to

query the key words beginning with s and the help information of the alias.

Ruijie#s?

*s=show show start-chat start-terminal-service

If an alias represents more than one word, the command will be displayed in brackets. For example, if

you set sv stand for show version in the privileged EXEC mode, then:

Ruijie#s?

*s=show *sv="show version" show start-chat

start-terminal-service

The alias must begin with the first letter of the command. The first letter of the command cannot be a

space. The space before the command cannot be used as a valid alias.

Ruijie# s?

show start-chat start-terminal-service

The command alias also has its help information. For example, if the alias ia represents ip address in

the interface configuration mode, then:

Ruijie(config-if)#ia ?

A.B.C.D IP address

dhcp IP Address via DHCP

Ruijie(config-if)# ip address

The above help information lists the parameters of ip address and shows the actual command name.

You must enter an entire alias; otherwise it cannot be recognized.

Use the show aliases command to show the aliases setting in the system.

Configuration

Examples

The following example uses def-route to represent the default route setting of ip route 0.0.0.0 0.0.0.0

192.168.1.1 in the global configuration mode:

Ruijie# configure terminal

Ruijie(config)# alias config def-route ip route 0.0.0.0 0.0.0.0 192.168.1.1

Ruijie(config)#def-route?

*def-route="ip route 0.0.0.0 0.0.0.0 192.168.1.1"

Ruijie(config)# end

Ruijie# show aliases config

globle configure mode alias:

def-route ip route 0.0.0.0 0.0.0.0

192.168.1.1

Commands

Command

Description

show aliases

Displays the aliases settings.

Platform

Description

N/A

Command Reference Command Line Interface Commands

1.2 privilege

Use this command to attribute the execution rights of a command to a command level in global

configuration mode. Use the no form of this command to restore the default setting.

privilege mode [ all ] [ level level | reset ]command-string

no privilege mode [ all ] [ level level ]command-string

Parameter

Description

Parameter

Description

mode

CLI mode of the command to which the execution rights are

attributed.

all

Command alias

level level

Specifies the execution right levels (0–15) of a command or

sub-commands

reset

Restores the command execution rights to its default level

command-string:

Command string to be authorized

Defaults

N/A

Command

Mode

Global configuration mode.

Usage Guide

The following table lists some key words that can be authorized by the privilege command in CLI

mode. The number of command modes that can be authorized may vary with different devices. In the

global configuration mode, you can use the privilege ? command to list all CLI command modes that

can be authorized.

Mode

Descripton

config

Global configuration mode.

exec

Privileged EXEC mode

interface

Interface configuration mode

ip-dhcp-pool

DHCP address pool configuration mode

ip-dhcp-pool

DHCP address pool configuration mode

keychain

KeyChain configuration mode

keychain-key

KeyChain-key configuration mode

Configuration

Examples

The following example sets the password of CLI level 1 as test and attribute the reload rights to reset

the device:

Ruijie(config)#privilege exec level 1 reload

You can access the CLI window as level-1 user to usef the reload command:

Ruijie>reload ?

LINE Reason for reload

<cr> You can use the key word all to attribute all sub-commands of reload to level-1 users:

Ruijie(config)# privilege exec all level 1 reload

Command Reference Command Line Interface Commands

After the above setting, you can access the CLI window as level-1 user to use all sub commands of the

reload command:

Ruijie>reload ?

LINE Reason for reload

at reload at a specific time/date

cancel cancel pending reload scheme

in reload after a time interval

<cr>

Commands

Command

Description

enable secret

Sets the CLI-level password.

Platform

Description

N/A.

1.3 show aliases

Use this command to show all the command aliases or aliases in special command modes.

show aliases [ mode ]

Parameter

Description

Parameter

Description

mode

Mode of the command represented by the alias.

Defaults

N/A.

Command

Mode

Privileged EXEC mode.

Usage Guide

This command displays the configuration of all aliases if no command mode is input.

Configuration

Examples

The following example displays the command alias in privileged EXEC mode:

Ruijie#show aliases exec

exec mode alias:

h help

p ping

s show

u undebug

un undebug

Commands

Command

Description

alias

Sets a command alias.

Command Reference Command Line Interface Commands

Platform

Description

N/A.

Tabla de contenidos

Otros manuales de Cambiar de Ruijie

Ruijie

Ruijie RG-S6250-48XS8CQ Series Manual

Ruijie

Ruijie RG-NBS3100 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S5000-24GT4MS-E Manual de instalación y funcionamiento

Ruijie

Ruijie Reyee RG-NBS7003 Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6910-3C Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6520 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-PF2920U-4GT1MS-P Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S7808C Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S2915-L Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6920-4C Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6120 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6930-2C Manual de instalación y funcionamiento

Ruijie

Ruijie RG-PF2920-DPBOX-P Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-CS85 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S5000-E Series Cómo utilizar

Ruijie

Ruijie RG-S6510-4C Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S7800 Series Manual

Ruijie

Ruijie RG-S6250-48XS8CQ Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6100 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6580-24DC8QC Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S6110 Series Manual de instalación y funcionamiento

Ruijie

Ruijie RG-S3250E Series Manual de usuario

Ruijie

Ruijie Reyee RG-ES126S-LP V2 Manual de usuario

Ruijie

Ruijie RG-S6980-64QC Manual de instalación y funcionamiento

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Manual de usuario