RS PRO RS 155B Manual de usuario
Instruction Manual
RS 155B (162-4455) / RS 156B (162-4456)
RS 157B (162-4457) / RS 158B (162-4458)
Clamp Meter
EN
RS 158B
Press 2 sec
1
150B Series / EN
Warning
. . . . . . . . . .
. . . . . . . . . .
. . . . . . . . . .
. . . . . . . .
Safety sheet
. . . . . . . . .
. . . . . . . . . .
. . . . . . . . . .
. . . . . . . .
. . . . . . . . .
Read First
Safety Information
Understand and follow operating instructions carefully.
Use the meter only as specified in this manual; otherwise, the
protection provided by the meter may be impaired.
WARNING
Identifies hazardous conditions and actions that could cause
BODILY HARM or DEATH
CAUTION
Identifies conditions and actions that could DAMAGE the meter
or equipment under test
WARNING
˙When using test leads or probes, keep your fingers behind
the finger guards.
˙ Individual protective equipment should be used if HAZARD-
OUS LIVE parts in the installation where measurement is to
be carried out could be ACCESSIBLE.
˙Remove test lead from meter before opening the battery
door or meter case.
˙Use the meter only as specified in this manual or the protec-
tion by the meter might be impaired.
˙ Always use proper terminals, switch position, and range for
measurements.
˙ Verify the meter’s operation by measuring a known voltage.
If in doubt, have the meter serviced.
˙Do not apply more than the rated voltage, as marked on
meter, between terminals or between any terminal and
earth ground.
˙Use caution with voltages above 30 V ac rms, 42 V ac peak,
or 60 V dc. These voltages pose a shock hazard.
˙To avoid false readings that can lead to electric shock and
injury, replace battery as soon as low battery indicator blinks.
˙Disconnect circuit power and discharge all high-voltage
capacitors before testing resistance, continuity, diodes, or
capacitance.
˙Do not use meter around explosive gas or vapor.
˙ To reduce the risk of fire or electric shock do not expose
this product to rain or moisture.
˙ Probe assemblies to be used for MAINS measurements
shall be RATED as appropriate for MEASUREMENT
CATEGORY III or IV according to EN 61010-031 and shall
have a voltage RATING of at least the voltage of the circuit
to be measured.
Warning Safety sheet
2
150B Series / EN
CAUTION
˙Disconnect the test leads from the test points before chang-
ing the position of the function rotary switch.
˙Never connect a source of voltage with the function rotary
switch in Ω, %,and position.
˙Do not expose meter to extremes in temperature or high
humidity.
˙ Never set the meter in Ω, %,and function to measure
the voltage of a power supply circuit in equipment that could
result in damage the meter and the equipment under test.
Symbols as marked on the Meter and Instruction
manual
Unsafe Voltage
To alert you to the presence of a potentially hazardous voltage,
when the Tester detects a voltage ≧30 V or a voltage overload
(OL) in V .The symbol is displayed.
Maintenance
Do not attempt to repair this meter. It contains no user
serviceable parts. Repair or servicing should only be performed
by qualified personnel.
Cleaning
Periodically wipe the case with a dry cloth and detergent.
Do not use abrasives or solvents.
Risk of electric shock
See instruction manual
DC measurement
Equipment protected by double or reinforced
insulation
Battery
Earth
AC measurement
Conforms to EU directives
EApplication around and removal from hazardous live
conductors is permitted
Do not discard this product or throw away.
3
150B Series / EN
Feature
˙10000 Count digital display
˙Active Backlit,Large scale display
˙VoltSeek (None Contact Voltage)
˙Analog Bar graph
˙True RMS reading on AC and AC+DC mode
˙Memory Save/Load (data amount up to 1000 )
˙Data logger (data amount up to 9999 )
˙Bluetooth wireless communication
˙Torch lightening when clamping
˙Auto AC/DC 1000 Amps capability and selection (For 158B)
˙Auto AC/DC 600 Amps capability and selection (For 156B)
˙Auto AC/DC 1000 Volts capability and selection
˙Auto Ohms/Continuity/Diode selection
˙100K Resistance capability
˙Continuity Beeper
˙Frequency Counter
˙Power and Power factor measurement
˙Total Harmonics distortion and Harmonics 1 to 25
˙Capacitance capability
˙°C / °F Temperature Function (For 158B)
˙Inrush Current
˙DCA Auto-Zeroing Button (For 156B/158B)
˙Peak Hold
˙MIN/MAX HOLD
˙Smart Data Hold
˙Phase rotation indication
˙Flex AC Current
˙High frequency rejection
˙Auto Powet Off
˙CAT.Ⅳ600V / CAT.Ⅲ1000V Safety Standard
4
150B Series / EN
Unpacking and Inspection
Upon removing your new Power Clamp Meter from its packing,
you should have the following items:
1. Power Clamp Meter
2. Test leads. set (1 x Black, 1 x Red)
3. Temperature Probe (For 158B)
4. User Manual
5. Carrying case
6. Battery
The Meter Description
Press 2 sec
5
150B Series / EN
Power On / Off
Power on
Auto Power Off
After idle 15 min
The meter can work again by turning it on from the OFF
position.
After turning on the meter,
the LCD will show Full,
half, and low to indicate
the battery capacity.
6
150B Series / EN
Auto Power Off (APO) disable :
Press OK button while tuning meter on from OFF position.
Push Buttons
Bluetooth
UP/DOWN
LEFT RIGHT
Menu Operation
Example
Use arrow keys to move the blinking cursor to the
target icon, and then press OK button
Use arrow keys to move the blinking cursor to the
target icon, and then press OK button for more
than 2 seconds.
The icon without underline means the function is
not executed.
The icon with underline means the function is
executed.
7
150B Series / EN
Making Basic Measurements
Preparation and Caution Before Measurement
: Observe the rules of Warnings and Cautions
The figures on the following pages show how to make
basic measurements.
When connecting the test leads to the DUT (Device Under Test),
connect the common test lead before connecting the live lead.
When removing the test leads, remove the test live lead before
removing the common test lead.
Measuring Voltage
V
8
150B Series / EN
Warning
To avoid electrical shock, hazard or damage to meter, do not
attempt to measurement that might exceed 1000 V dc or ac
RMS. Do not apply more then 1000 V dc or ac RMS between
the common input terminal and earth ground.
Note - If the measured voltage is greater than 30 V dc or ac
RMS, the display will show the " " symbol.
Measuring Current
- DO NOT clamp on any conductor while the meter power on.
- 155B/157B has only AC current measurement mode.
- Torch lightening when clamping.
I
OK
I+(-I)=0
OK
I
I
I
OK
I
CAT.Ⅳ.600V
CAT.Ⅲ.1000V
with respect to
earth for the jaw.
Tactile Barrier for
hand guard.
Do not hold
the meter across
the Tactile Barrier.
9
150B Series / EN
AUTO SENSE mode :
Display measurement result at AC only with RMS value or
DC value, it depends on whichever is greater.
AC mode : AC only with RMS value.
DC mode : DC value.
AC+DC mode : AC+DC RMS value.
Note
- Press MODE button to enter the AC/DC/AC+DC mode.
- Press MODE button for more than 2 seconds to return to the
AUTO SENSE mode.
PEAK HOLD (AC mode only)
ACV mode
>2SEC
>2SEC
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Instrumento de medición de RS PRO
RS PRO
RS PRO ISM 400 Manual de usuario
RS PRO
RS PRO RS-95 Manual de usuario
RS PRO
RS PRO RS-1260 Manual de usuario
RS PRO
RS PRO RS-5200 Manual de usuario
RS PRO
RS PRO RS-90 Manual de usuario
RS PRO
RS PRO RS-1340 Manual de usuario
RS PRO
RS PRO 2377271 Manual de usuario
RS PRO
RS PRO RS-960 Manual de usuario
RS PRO
RS PRO RS-8920 Manual de usuario
RS PRO
RS PRO RS-9985 Manual de usuario
RS PRO
RS PRO RSST-2000 Series Manual de usuario
RS PRO
RS PRO RS-326 Manual de usuario
RS PRO
RS PRO 232.50.100 Manual de usuario
RS PRO
RS PRO ILM 1332A Manual de usuario
RS PRO
RS PRO RSSA3000X Manual de usuario
RS PRO
RS PRO 623-883 Manual
RS PRO
RS PRO RS-137 Manual de usuario
RS PRO
RS PRO RS-128M Manual de usuario
RS PRO
RS PRO ICM 20 Manual de usuario
RS PRO
RS PRO RS-8890D Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario