RS PRO ICM 134 Manual de usuario

Instruction Manual

ICM 134

Clamp Meter

EN DE ES IT FR



EN - 2

Safety Information

Read and understand this Instruction

Manual completely before using this

instrument. Failure to observe the warnings

and cautions in this Instruction Manual may

result in injury or death, or damage to the

instrument and other equipment or

property.

If this instrument is used in a manner not

specified in these instructions, the protec-

tion provided by the instrument may be

impaired.

WARNING

-Examine the instrument and probes and

leads before use. Do not use the instru-

ment if it is wet or damaged, or if you

suspect it is not operating correctly.

-When using the instrument, test leads or

probes, keep your fingers behind the

finger guards.

-Remove the test lead from the instrument

before opening the battery cover or instru-

ment case.

-Always use the correct terminals, switch

position and range for measurements.

-Verify the instrument is operating correctly

by measuring a known voltage before

use. If in doubt, have the instrument

serviced.

-Do not apply more than the rated voltage

as marked on the instrument between

terminals, or between any terminal and

earth ground.

-Use caution when measuring voltages

above 30 Vac rms or 60 Vdc. These

voltages pose a shock hazard.

-To avoid incorrect readings that can lead

to electric shock, replace the battery as

soon as low battery indicator appears

in the display.

-Disconnect the circuit power and

discharge all high-voltage capacitors

before making resistance, continuity, or

diode measurements.

-Do not use the instrument in a Hazardous

Area or around explosive gasses or

vapours.

EN - 3

-Wear suitable Personal Protective

Equipment when working around or near

hazardous Live conductors which could

be accessible.

-Do not use the thermocouple to measure

the temperature of Hazardous Live

conductors or equipment.

Caution

-Disconnect the test leads from the test

points before changing the position of the

function rotary switch.

-Never connect the instrument to a source

of voltage with the function rotary switch in

Ω/ ;/Aposition.

- If possible, do not work alone, so

assistance can be given if required.

-Do not expose the instrument to extremes

of temperature or high humidity.

-If this instrument is used in the vicinity of

equipment which generates electro

magnetic interference, the display may

become unstable or the measurements

may be subject to large errors.

The following symbols may appear on

the instrument and in this Instruction

Manual:

Risk of electric shock

Refer to Instruction Manual

 Direct Current (dc)

Alternating Current (ac)

<Battery

Earth

Equipment protected throughout by

double or reinforced insulation

Conforms to EU directives

Dispose of this equipment in

accordance with local regulations.

EApplication around and removal

from hazardous Live conductors is

permitted.

EN - 4

Maintenance

Do not attempt to repair this Instrument. It

contains no user-serviceable parts. Repair

or servicing should only be performed by

qualified personnel. This instrument

should be calibrated yearly, or more

frequently if used in harsh conditions or if

it is suspected of being inaccurate.

For calibration and repair contact RS

Components - the address is given at the

end of these instructions.

Cleaning

Periodically wipe the case with a damp

cloth and detergent. Do not use abrasives

or solvents.

EN - 5

To conserve battery power, the Auto Power

-off function will turn the instrument off

approximately 10 minutes after the last

operation.

10min

To disable the Auto Power-off function:

Turn the instrument off, press and hold the

“Backlight” button and turn the rotary switch

to the required function. The auto Power-off

is disabled until the next time the instru-

ment is turned off and on again.

Power On / Off

Auto Power Off

EN - 6

ACV / DCV

Resistance

EN - 7

Diode / Continuity

;

EN - 8

DC µA

Capacitance

Note –To improve the measurement

accuracy of a small value capacitor, record

the reading with the test leads open circuit,

then substract the residual capacitance of

the Instrument and leads from the final

measurement.

CUNKNOWN =CMEASUREMENT - CRESIDUAL

EN - 9

Temperature

Data Hold

392A

EN - 10

ACA

392A

CAT.Ⅲ.600V

with respect to

earth for the jaw.

Tactile Barrier for

hand guard.

Do not hold

the meter across

the Tactile Barrier.

OK I + (-I) = 0

Back Light

Tabla de contenidos

Otros manuales de Instrumento de medición de RS PRO

RS PRO

RS PRO RS-3809 Manual de usuario

RS PRO

RS PRO RS-9968BT Manual de usuario

RS PRO

RS PRO 236-9298 Manual de usuario

RS PRO

RS PRO ICM 20 Manual de usuario

RS PRO

RS PRO RS-1150 Manual de usuario

RS PRO

RS PRO IM-194 Manual de usuario

RS PRO

RS PRO 877-1791 Manual de usuario

RS PRO

RS PRO ILM 1332A Manual de usuario

RS PRO

RS PRO ICM A6N Manual de usuario

RS PRO

RS PRO 2377271 Manual de usuario

RS PRO

RS PRO IM-195 Manual de usuario

RS PRO

RS PRO SLM 1353M Manual de usuario

RS PRO

RS PRO HS-608 Manual de usuario

RS PRO

RS PRO RS-5200 Manual de usuario

RS PRO

RS PRO 623-883 Manual

RS PRO

RS PRO IM-502 Manual de usuario

RS PRO

RS PRO RM-804 Manual de usuario

RS PRO

RS PRO RS-8890D Manual de usuario

RS PRO

RS PRO IPM 241 Manual de usuario

RS PRO

RS PRO RS-91 Manual de usuario

RS PRO

RS PRO RS-9985 Manual de usuario

RS PRO

RS PRO RS-72H Manual de usuario

RS PRO

RS PRO RSPRO-P30R Manual de usuario

RS PRO

RS PRO RS-960 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario