Royal Sovereign RSH-1650 Manual de usuario
www.royalsovereign.com
ROLL LAMINATOR
Service Manual
3 ~ 3
4 ~ 13
4 ~ 5
6 ~ 6
7 ~ 9
9 ~ 10
11 ~ 13
14 ~ 16
14 ~ 14
15 ~ 15
15 ~ 15
15 ~ 15
15 ~ 15
16 ~ 16
16 ~ 16
17 ~ 17
17 ~ 17
17 ~ 17
18 ~ 18
19 ~ 28
19 ~ 23
24 ~ 28
29 ~ 43
30 ~ 36
37 ~ 43
44 ~ 47
2.1) Rollers Not Heating ………………………………………………………………………………
2.2) Rollers Over Heating ……………………………………………………………………………
2.3) Rollers Not Running ………………………………………………………………………………
2.4) No Main Power ……………………………………………………………………………………
Table of Contents
1.Safety Precautions ………………………………………………………………………
2.Troubleshooting ……………………………………………………………………………
7.Exploded Drawings ………………………………………………………………………
7.1) RSH-1650 Whole Exploding Drawing and Part Exploding Drawing ……………………
7.2) RSH-1050 Whole Exploding Drawing and Part Exploding Drawing ……………………
8.Wire Diagram ……………………………………………………………………………………
3.2) Left Cover …………………………………………………………………………………………
6.2) RSH-1050 Parts List …………………………………………………………………………………
4.2) Adjusting Front and Rear Roller ………………………………………………………………
5. Optioning Equipment ……………………………………………………………………
6. Parts List …………………………………………………………………………………………
6.1) RSH-1650 Parts List ………………………………………………………………………………
3.3) Rear Cover …………………………………………………………………………………………
4.Adjustments ……………………………………………………………………………………
4.1) Adjusting Take-Up Shaft Speed ………………………………………………………………
2.5) Count Sensor Not Working ………………………………………………………………………
3.4) Main PCB ……………………………………………………………………………………………
3.5) Sub PCB ………………………………………………………………………………………………
3.6) Heaters ………………………………………………………………………………………………
3.7) Cross Cutter …………………………………………………………………………………………
3.Replacing Parts ………………………………………………………………………………
3.1) Right Cover …………………………………………………………………………………………
2
18 ~ 22
1. Safety Precautions
Safety Precaution
Failure to comply any of the following safety procedures could result in
serious injury. Please read the instructions carefully and keep for future
reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct
voltage.
3. Keep hands and clothing (ie.Neckties)away from rollers. The rollers are pinch
points that can trap body parts or clothing and cause serious injury .
4. Keep flammable and wet objects away from the machine .
5. Place machine on a sturdy and level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled ,and unplugged from the outlet prior to
moving and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should
make repairs.
10. Do not attempt to laminate items that exceed total recommended material
thickness for the unit.
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the
machine.
13. Do not cover the surface of the machine until the machine has completely
cooled.
3
Note: While repairing:
a. Make sure the power plug is unplugged from the power outlet.
b. Open both side covers and rear cover.
c. Be sure to follow the steps below in order.
2.1 Rollers Not Heating
1. Improper laminating mode.
2. Heating wire is not connected to the main PCB.
3. Blown (burnt) upper and/or lower wire fuse (T/Fuse).
4. Defective Bi-Metal.
5. Defective heater.
6. Defective Main PCB.
1. Improper laminating mode.
a. Ensure that the laminating mode is in the “Hot” mode, not the “Cold” mode.
Press “C/HOT” button on the control panel to change the mode.
2. Heating wire is not connected to the main PCB.
a. Connect the upper and lower heating wires to the main PCB.
18 ~ 22
2. Troubleshooting
CAUSES:
MEASURE
4
3. Blown (burnt) upper and/or lower wire fuse (T/Fuse).
a. Replace the T/Fuse wire located on the left-hand side.
4. Defective Bi-Metal.
a. Replace the Bi-Metal
5. Defective heater.
a. Using the multi-meter, test the continuity of the heater. If it fails, replace the heater.
b. Physically examine the heater assembly for breakage.
13. Remote Control and Foot Pedal wires.
a. Replace the PCB Main.
6. Defective Main PCB.
BI- METAL
Multi-meter
Broken
WIRE-
T/FUSE
5
2.2) Rollers Over Heating
1. Lower and upper heat sensors are reversed on the PCB Main.
1. Wires for lower and upper heat sensors are reversed on the main PCB.
a. Reverse the heat sensors.
a. Replace the T/Fuse wire located on the left-hand side.
3. Defective heater.
a. Test continuity of the heater. If it fails, replace the heater.
b. Glass tube that surrounds heating coil is broken – replace the heating element.
a. Replace the PCB Main.
2. Defective T/Fuse wire.
MEASURES
4. Defective Main PCB.
CAUSES
2. Defective T/Fuse wire.
3. Defective heater.
4. Defective main PCB.
WIRE-T/FUSE
Connector-Wire
Sensor
6
2.3) Rollers Not Running
1. No power to the unit.
2. Emergency switch is engaged.
3. Disengaged Paper Guide switch.
4. Opened safety cover.
5. Film is jammed on the rollers.
6. Disconnected motor wire.
7. Blown motor fuse.
8. Defective main motor.
9. Defective main PCB.
1. No power to the unit.
a. Make sure the power plug is connected to the proper source of outlet
(220V, 15Amp, & single phase).
2. Emergency switch is engaged.
a. Disengage the emergency switches located on the front and on the rear of the machine
by rotating the knob clock-wise.
3. Disengaged Paper Guide switch.
a. Properly position the paper guide to engage the switch.
MEASURES
CAUSES
Front Left Rear Left
Paper Guide
7
4. Opened safety cover.
a. Close the safety cover and double check to insure that the safety cover switch
is engaged.
Note: By closing the safety cover, it engages the safety cover switch.
5. Film is jammed on the rollers.
a. Un-jam the film using a combination of the pressure lever and reverse button.
6. Disconnected motor wire.
a. Check the motor wire connection in both locations.
Safety Cover Switch
Switch is engaged
Motor wire connector
from the Motor
Motor wire connector
from the PCB
8
7. Blown motor fuse.
a. Replace the motor fuse located above the main power switch.
8. Defective main motor.
a. Replace the main motor.
8. Defective main motor.
a. Replace the main motor.
9. Defective main PCB.
a. Replace the main PCB.
2.4) No Main Power
1. No electricity.
2. Blown main fuse.
3. Disconnected main power wires.
4. Defective transformer.
1. No Electricity.
a. Double check to insure that you have electricity from your outlet.
b. Check the circuit breaker.
c. Double check that source of power is 220V, 15Amp, and single phase.
MEASURES
CAUSES
Motor Fuse
9
2. Blown main fuse.
a. Replace the main fuse located above the main power switch.
3. Disconnected main power wires.
a. Check that the main power wires are properly connected.
4. Transformer is defective
a. Replace the transformer.
Main Fuse
Main Power Wires
Transformer
10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Laminadora de Royal Sovereign
Royal Sovereign
Royal Sovereign RSL-382CR Manual de usuario
Royal Sovereign
Royal Sovereign RSL-2701 Manual de usuario
Royal Sovereign
Royal Sovereign RSH-380SL Manual de usuario
Royal Sovereign
Royal Sovereign RSC-LS series Manual de usuario
Royal Sovereign
Royal Sovereign ES-1315 Manual de usuario
Royal Sovereign
Royal Sovereign PL - 922 Manual de usuario
Royal Sovereign
Royal Sovereign Fremont 65H Manual de usuario
Royal Sovereign
Royal Sovereign RSH-1151 Manual de usuario
Royal Sovereign
Royal Sovereign RSH-1151 Manual de usuario
Royal Sovereign
Royal Sovereign ES-400 Manual de usuario
Royal Sovereign
Royal Sovereign APL-330U Manual de usuario
Royal Sovereign
Royal Sovereign RSS-1050 Manual de usuario
Royal Sovereign
Royal Sovereign Paramount 65X Manual de usuario
Royal Sovereign
Royal Sovereign ES-410 Manual de usuario
Royal Sovereign
Royal Sovereign IL-926W Manual de usuario
Royal Sovereign
Royal Sovereign RSC-LS series Manual de usuario
Royal Sovereign
Royal Sovereign RSC-820CL Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1050CL Manual de usuario
Royal Sovereign
Royal Sovereign RSL-2702S Manual de usuario
Royal Sovereign
Royal Sovereign NR-1201 Manual de usuario
