Royal Sovereign RSS-1050 Manual de usuario
Royal Sovereign LAMINATORS
OWNER'S MANUAL
RSS-1200,1050 ,685
PLEASE READ AND SAVE INSTRUCTIONS.
- 1 -
MEMO ----------------------------------------------------------------------------------------------
-
27
1.HOT FILM -----------------------------------------------------------------------------------------
2.COLD FILM ---------------------------------------------------------------------------------------
CONTROL OF ROLLER PRESSURE ------------------------------------------------------
-
INSTRUCTIONS FOR CONTROL PANEL ------------------------------------------------
-
PAGETOPICS
INTRODUCTION --------------------------------------------------------------------------------
-
SAFETY PRECAUTIONS --------------------------------------------------------------------
-
3
3
3.HOW TO USE BUTTONS -------------------------------------------------------------------
-
LAMINATING STEPS ---------------------------------------------------------------------------
-
1.HOT LAMINATING ----------------------------------------------------------------------------
-
2.COLD LAMINATING --------------------------------------------------------------------------
-
CHARACTERISTICS -----------------------------------------------------------------------------
-
SPECIFICATIONS ---------------------------------------------------------------------------------
-
18~20
21
22
22
8
9
10
11
5
6
7
8
4
4
26WARRANTY --------------------------------------------------------------------------------------
-
24
24
25
25
IT'S NOT OUT OF ORDER. --------------------------------------------------------------------
-
SPARE PART ----------------------------------------------------------------------------------------
-
IMPORTANT SAFETY CONCERNS. -------------------------------------------------------
-
MAINTENANCE ------------------------------------------------------------------------------------
-
TIPS FOR REMOTE CONTROL AND FOOT SWITCH ----------------------------------
METHOD FOR USING CUTTER --------------------------------------------------------------
-
1.CROSS CUTTER -------------------------------------------------------------------------------
-
2.SLITERS -------------------------------------------------------------------------------------------
-
14~17
18
22
23
SETTING UP FILM -------------------------------------------------------------------------------
HANGING FILM -----------------------------------------------------------------------------------
1.LCD WINDOW ----------------------------------------------------------------------------------
-
2.FUNCTIONS OF BUTTONS ----------------------------------------------------------------
-
12
13
A
DJUSTMENT OF FILM TENSION AND LOCATIONS --------------------------------
-
TABLE OF CONTENTS
NAMES OF MAJOR PARTS OF MACHINE ------------------------------------------------
- 2 -
5. Do not operate machine for any other purposes than its intended use.
6. Do not operate machine if electrical plug or power cord is damaged.
8. This machine is intended for indoor use only.
Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and
manufactured to provide years of continuous service in the professional environment.
To insure high quality lamination, please read this instruction manual thoroughly.
This manual will provide you with complete operating and maintenance information.
For additional product support or factory-direct ordering information.
Call Royal Sovereign Customer Service at (800) 397-1025.
liquids to spill inside.
to comply any of the following safety procedures could result in serious personal injury.
1. To prevent the possibility of electrical shock, do not immerse machine in water or permit
The safety recommendations outlined in this section are to be read, understood and
followed before operating machine. Keep this information for future reference. Failure
2. Do not allow articles of clothing (neckties, scarves, papers, etc.) near front or rear
machine openings as they could get caught by rollers and be pulled inside, causing
7. Turn off the power when unattended or not in use. Unplug machine before movig it or
when it is not in use for an extended period of time.
9. Do not alter or extend electric plug. Plug is configured for appropriate electrical supply.
10. The socket-outlet shall be installed mear the equipment and shall be easily accessible.
personal injury.
3. Do not insert sharp objects into front or rear machine openings. Do not place anything
in feed tray openings of machine other than appropriate laminating materials or pouches.
4. Do not attempt to laminate items that exceed total recommended material thickness.
INTRODUCTION
SAFETY PRECAUTIONS
- 3 -
Remote control device allows for control of the machine from the front or rear.
thickness of film and materials to be laminated.
Yes
Yes
1200(mm)
47.2(in)
1050(mm)
41.3(in)
685(mm)
27(in)
Yes
Yes
221
Yes
Film Alignment
Cutter-Cross
Foot-Switch
AC 100~120/ 200~240V 50~60Hz
6m/min (19.7ft/min)
3000W 3000W 2000W
13mm ( 0.5in)
25~250mic (1 ~ 10mil)Film Thickness
Cold and Hot Laminating
Cooling Blower
Take Up
Power Consumption
Max.Laminating Speed
Max.Laminating Width
Max.Laminating Thickness
Unit Dimensions
Unit Weight
RSS-1200
1070*650*1205(mm)
42.1*25.6*47.4(in)
190(Kg)
418(lbs)
140(Kg)
308(lbs)
100(Kg)
220(lbs)
1400*650*1210(mm)
55.1*25.6*47.4(in)
1550*650*1210(mm)
61*25.6*47.4(in)
Foot-Pedal Switch allows for hands-free operation. It is also designed for convenient use
the latest in laminating technology. It is designed for you to set temperature and speed as
necessary and have the machine remember your settings. Also, you can laminate anything
at high speed, regardless of thickness of material and type of film.
RS Roll Laminator Line are advanced laminators with time transcendental design, utilizing
RSS-1050 RSS-685Description
Voltage/Cycles
CHARACTERISTICS
Yes
Yes
SPECIFICATIONS
by anyone through the simple procedure of adjusting film tension in accordancs with the
Paper Counting
Length Measurement
- 4 -
1. FILM-UPPER 8. FOOT SWITCH
2. FILM-LOWER 9. REMOTE CONTROL SWITCH
3. TAKE-UP (ASS'Y-TAKE-UP) 10
.
CONTROL PANEL
4. IDLER BAR (UPPER) 11
.
PRESSURE LEVER
5. TABLE-FRONT 12
.
TENSION CONTROL KNOB
6. SHOE-HEATER,UPPER 13
.
ALIGNMENT KNOB
7. ASS'Y-STAND 14
.
TAKE-UP SWITCH
NAMES OF MAJOR PARTS OF MACHINE
1
2
3
4
5
6
7
8
9
10
11
12
13 14
- 5 -
1. HOW TO CONTROL TENSION
2. HOW TO ADJUST ALIGNMEN
T
Location control device is used when the edges of the lamination are unjustified.
As the drawing shows, when the alignment knob is turned clockwise, the upper film is
to left. Once proper alignment is reached, turn the Locking Nut tight against the Alignment
knob so the adjustment is set.
ADJUSTMENT OF FILM TENSION AND LOCATIONS
can adjust it, to some extent, and make wrinkles straighten from Anti-Wrinkle Part of the
Tension of film can be controlled depending on the state of lamination, but basically you
heat shoe. To increase the tension on the film, turn the knob clockwise.
To lower the tension, turn the handle counter clockwise. If lamination is curved upward,
it means that tension of upper film is high. In this case, it can be controlled by raising
moved to right. On the contrary, when the handle is turned counter-clockwise, it is moved
apply the method in reverse.
tension of lower film or lowering tension of upper film. If lamination is curved downward,
Alignment Knob.
Locking Nut
Tension Control Knob
필름
주름방지부
필름
열판
Film
Shoe-Heater
Film
Anti-Wrinkle
device
- 6 -
1. Set the glossy side of upper/lower film to face the heat.
( Glossy side is PET film and matte side is thermal polymer laminating film.)
2. Like picture 1, insert core into the left side of upper/lower film shaft.
3. Like picture 2 and 3, insert core into the right side of upper/lower film.
4. Like picture 4 and 5, adhere core closely.
(Make the right/left direction of fixing screw consistent.)
5. Locate film in the middle, and then fasten core fixing screw.
SETTING UP FILM
Picture 1
Upper Film
Lower Film
Upper Film
Lower Film
Picture 2
Picture 3
Picture 4
Picture 5
Core Fixing
Screw
- 7 -
1. HOT FILM
10. After checking the status of lamination, Place the pressure lever at the proper
lamination mode.
6. Allow some of the film with melted resin to stick to the Guiding Paper.
7. Repeat step 5 with lower roll film then stick it to the Guiding Paper.
fed through to the rear roller without tension.
8. Unwind 30~40cm(1~1.3ft) of both rolls of film, to loosen the film tension. This should be
1. Insert the bar into the core of roll film then place the bar on the machine.
HANGING FILM
beyond the second set of rollers.
9. Set speed at 1 and press the "RUN" button to feed film into the machine.
2. Place the Pressure Lever to the open mode (10~13mm).
3. Insert a piece of lightweight cardboard (Guiding Paper) between the rollers, through to
**IMPORTANT : It should reach beyond the second set of rollers. It should stick out
5cm (2") in front of front roller.
4. Pull the upper film around the upper idler bar to the anti-wrinkle device and stretch out
the film on the upper heat shoe.
5. When the temperature reaches 80°C (176°F), the resin is melting, stick the film on the
shoe.
SHAFT
LOWER IDLE BAR
UPPER ROLL FILM
SHAFT
LOWER ROLL FILM
GUIDING PAPER
HEAT SHOE
UPPER IDLE BAR
LOWER FILM
SHAFT
LOWER IDLE BAR
HEAT SHOE
Picture 1
- 8 -
2. COLD FILM
1. Take out the guiding table.
2. Put the shaft of roll film in each hole exactly.
3. Set the pressure lever to the proper lamination mode.(1mm/5mm/10~13mm)
4. Pull the film around the idler bar to the Anti-wrinkle device.
5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back.
**It is to be stuck on to roll up clock wise.
6. Place the sticky part of film on the upper shoe and get ready to laminate.
PAPER BACK
TAKE UP DEVICE
HEAT SHOE
UPPER FILM SHAFT
COLD FILM
UPPER IDLE BAR
- 9 -
1. For setting, pull the pressure lever out and turn the lever to following
the indication.
5. Laminating : Mode that you can do laminate 25mic(1mil) to 250mic(10mil)
2. 10~13mm Board : Mode that you can laminate 10~13mm(1/3" to 1/2")
3. 5mm Board : Mode that you can laminate 5mm(1/4") hard board
4. 1mm hard board : Mode that you can laminate 1mm(40mil) hard board
CONTROL OF ROLLER PRESSURE
***Methods of controlling pressure of the roller ***
- 10 -
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Laminadora de Royal Sovereign
Royal Sovereign
Royal Sovereign RSC-1650C Manual de usuario
Royal Sovereign
Royal Sovereign RSH-1151 Manual de usuario
Royal Sovereign
Royal Sovereign RSC-165C Manual de usuario
Royal Sovereign
Royal Sovereign APL-330U Manual de usuario
Royal Sovereign
Royal Sovereign APL-330U Manual de usuario
Royal Sovereign
Royal Sovereign ES-410 Manual de usuario
Royal Sovereign
Royal Sovereign APL-330U Manual de usuario
Royal Sovereign
Royal Sovereign HSH-1300 Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1650C Manual de usuario
Royal Sovereign
Royal Sovereign RSL-380 Manual de usuario
Royal Sovereign
Royal Sovereign RSC Series Manual de usuario
Royal Sovereign
Royal Sovereign CS-923 Manual de usuario
Royal Sovereign
Royal Sovereign NR-1201 Manual de usuario
Royal Sovereign
Royal Sovereign RSL2701S Manual de usuario
Royal Sovereign
Royal Sovereign CS-900 Manual de usuario
Royal Sovereign
Royal Sovereign ES-1315 Manual de usuario
Royal Sovereign
Royal Sovereign Quick Ready APL-340U Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1400L Manual de usuario
Royal Sovereign
Royal Sovereign RSL-2701 Manual de usuario
Royal Sovereign
Royal Sovereign RSC-1653P Manual de usuario
