Royal Sovereign Fremont 65H Manual de usuario

Fremont 65H

Royal Sovereign International Inc.

Owner's Manual

GRAPHIC LAMINATION

PRODUCTS

Please read and retain these instructions.

To register your product, please go to www.royalsovereign.com

www.royalsovereign.com

CONTENTS

1. Introduction 3

2. Safety Precautions 4

4. Installation 5

5. Product Identification 7

6. Control Panel 8

7. Using Foot Pedal 9

8. Loading Film 9

9. Threading Film 9

9.1 Laminting 10

9.2 Mounting 10

11. Maintenance 10

12. Troubleshooting 11

10. Adjusting the gap of both rollers 10

13. Specifications 12

14. Warranty 13

Graphic Lamination Products

1. INTRODUCTION

Thank you for choosing a Royal Sovereign laminator. It has been designed and

manufactured to provide years of continuous service.

For complete operating and maintenance information please read this manual

thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all

other contents for shipping damage.

Damage should be brought to the immediate attention of the delivering carrier.

Model Fremont 65H

2. SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result in serious injury. Please read the instructions

carefully and keep for future reference.

1. Only a licensed electrician should install wiring and outlet for the laminator.

2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.

3. Once the air supply is connected to the laminator, make sure the pressure valve is set less than 0.6 MPa (87PSI).

This can be adjusted by the pressure regulating valve which is located inside the right-hand cabinet assembly.

4. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points that can trap body parts or

clothing and cause serious injury.

5. Keep flammable and wet objects away from the machine.

6. Place the laminator on a level surface, then adjust the casters to the locked position in order to keep the laminator steady.

7. Avoid excessive sunlight, humidity and extreme temperatures.

8. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.

9. Keep out of reach of children.

10. Only Royal Sovereign authorized maintenance and service technicians should make repairs.

11. Do not attempt to laminate items that exceed total recommended material thickness for the unit.

12. When cleaning the machine, don't use flammable sprays or materials.

13. Do not touch the rollers when they are hot or place foreign objects inside the machine.

14. Do not cover the surface of the machine until the machine has completely cooled.

15. If emergency happen, press emergency switch immediately.

16. Temperature of circumstance: 20°C ± 5°C; humidity of circumstance: < 95%(20°C ± 5°C).

17. Warning - Hazardous Moving Parts – Keep Fingers And Other Body Parts Away.

Fremont 65H

3. INSTALLATION

Note: The laminator should be installed by a trained service technician.

The laminator comes fully assembled. Upon arrival, thoroughly inspect the unit. It is imperative that any shipping damage

is reported and a claim is filed with the delivering carrier immediately upon receipt.

The laminator should be located in an area with adequate work space for feeding graphics and lamination materials.

Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.

Once the laminator is in place, lock the casters into position. Always unlock the casters when moving to a different location.

ELECTRICAL REQUIREMENTS

Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance

with electrical codes in your area.

120V UL 230V UL 240V UK

220V EU 220V AU

4. INCLUDED WITH LAMINATOR

Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the

reseller immediately upon receipt of shipment.

Part Name Quantity Picture

Laminator 1

Owner's Manual 1

Spare Motor Fuse - FUSE(50T)

(6.3A) 1

Spare Main Power Fuse - FUSE(65TS)

10A/20A 1

Key 2

Fremont 65H

Royal Sovereign International Inc.

Owner's Manual

GRAPHIC LAMINATION

PRODUCTS

Pleaseread and retain these instr uctions.

Toregister your product, please go to www.royalsovereign.com

www.royalsovereign.com

5. PRODUCT IDENTIFICATION

1Film Tension Knob

9Shaft Feeder

2Shaft Release Liner

10 Air Intake

3Emergency Switch

11 Knob Speed Control

4Roller

12 Button

5Safety Sensor

13 Pressure Gauge

6Table Front

14 Pressure Regulating Valve

7Caster

15 Reversing Valve

8Foot Switch

16 Door Lock

17 Gap Adjustment

18 Knob Temp. Control

Fremont 65H

6. CONTROL PANEL

TEMP. To change the mode from cold to hot or oppositely. Temperature

for hot mode on upper roller is max .

REV To reverse the rollers, press and hold the button.

Speed Rotate the knob to control the roller’s speed from 0 to 6m/min.

Run/Stop To start or stop the rollers.

Pressure gage: To indicate the pressure of top roller from 0 to 1Mpa

Height control crank：To set the

height limit block(*Make sure the

upper roller is in the highest

location).

Height scaleplate: To indicate the

gap of the two laminating rollers.

(145Psi) pressure value.

Pressure regulating valve: To change the pressure of top roller from 0 to

0.6Mpa (87Psi) pressure value.

Reversing valve: To make the top roller go up and down.

Fremont 65H

7. USING FOOT PEDAL

Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed,

you may use the foot pedal to operate the laminator for “Hands Free Operation.” To activate

the machine, press the foot pedal once and then release. Repeat to stop the rollers.

8. LOADING FILM

Royal Sovereign films are woundwith the adhesive side facing the inside of the roll

(adhesive in).

Loading laminate to the upper film shaft:

Remove the upper film supply shaft from the laminator and load the laminate through the film shaft. Center the film on

the shaft by referencing the centering markers supplied on the film shaft.

Note the direction of the laminate adhesive on the upper film shaft before loading onto the laminator.

9. THREADING FILM

1. Turn the power switch on (“I” position). The power switch is located on the rear left side of the unit.

2. Complete the steps as in the “LOADING FILM” section.

3. Load the roll of material to be laminated onto the bottom film supply shaft. Center with the laminate on the upper

film shaft by using the centering markers supplied on the film shaft.

Open the laminator rollers. Please refer to Section 10: Adjusting the space of both rollers.

Bring you material on the bottom supply shaft that needs to be laminated over the laminator feed table and slightly

into the open rollers.

6. Run you laminate from your upper supply shaft below the top idle bar and around the top laminator roller

so that it is past the laminator roller nip position.

Close the laminator rollers together by using the Reversing Valve.

8. Separate the laminate release liner from the laminate and tape to the upper Release Liner Shaft.

(Please reference 9. THREADING FILM for proper laminator webbing).

·Please Adjust the wheel to Change the roller pressure with different Material for the best Laminating quality.

1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release

liner.

2. With the image facing up, align the image onto the board. Press firmly from the center out.

3. Adjust the pressure lever to ensure the proper opening.

4. Flip the image over the upper roller and hold on to the release liner.

5. Press the foot pedal once, and then let it go while slowly pulling the release liner as the board enters the main roller nip.

Press the foot pedal once again when the board has completely exited from the rear of the unit.

Trim the board if necessary.

11. MAINTENANCE

Cleaning the Body of the laminator

1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.

10. Adjusting the gap of both rollers

Warning: Make sure the upper roller is at the highest location

when you adjust the crank.

Turn the crank clockwise to make the height limit-block go upward, inversely turn it counterclockwise to make the height

limit-block go downward.

9.1. Laminating

9.2. Mounting

Tabla de contenidos

Otros manuales de Laminadora de Royal Sovereign

Royal Sovereign

Royal Sovereign RSL-2702 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1650CLT Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1653P Manual de usuario

Royal Sovereign

Royal Sovereign CS-900 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1401CLTW Manual de usuario

Royal Sovereign

Royal Sovereign RSL-2701 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1400L Manual de usuario

Royal Sovereign

Royal Sovereign ES-1315 Manual de usuario

Royal Sovereign

Royal Sovereign RSL1062 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-820CL Manual de usuario

Royal Sovereign

Royal Sovereign RSC-165C Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1401C Series Manual de usuario

Royal Sovereign

Royal Sovereign ES-1310 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1650C Manual de usuario

Royal Sovereign

Royal Sovereign RPA-5254R Manual de usuario

Royal Sovereign

Royal Sovereign RSC-880LS Manual de usuario

Royal Sovereign

Royal Sovereign Quick Ready APL-340U Manual de usuario

Royal Sovereign

Royal Sovereign RSC-5500H Manual de usuario

Royal Sovereign

Royal Sovereign RSL-2702 Manual de usuario

Royal Sovereign

Royal Sovereign NB-1900N Manual de usuario

Royal Sovereign

Royal Sovereign APL-230 Manual de usuario

Royal Sovereign

Royal Sovereign RSC-1650C Manual de usuario

Royal Sovereign

Royal Sovereign ES-400C Manual de usuario

Royal Sovereign

Royal Sovereign RSH-1151 Manual de usuario

Manuales populares de Laminadora de otras marcas

Renz

Renz HT 330 L Manual de usuario

Gfp

Gfp 44TH Manual de usuario

Lapis

Lapis Lamina006 Manual de usuario

Hama

Hama L44B Manual de usuario

PAVO

PAVO FLORIDA Manual de usuario

M-Triangel

M-Triangel MT-102 Manual de usuario

Akiles

Akiles PROLAM 230 Manual de usuario

D&K

D&K Masterpiece 550 Manual de usuario

Falcon

Falcon F-40 Manual de usuario

LEITZ

LEITZ EasyLaminator A4 Manual de usuario

LEITZ

LEITZ coldLAM CS9 Manual de usuario

kala

kala Starter 1080 Manual de usuario

Fellowes

Fellowes Venus A3 Manual de usuario

Qomolangma

Qomolangma FMJ-1400-WA-PLUS Manual de usuario

Opus

Opus Coverator 330 Manual de usuario

ALDI

ALDI OL 250-L Manual de usuario

Phoenix

Phoenix 2700-DH Manual de usuario

acropaq

acropaq AL-3400 Manual de usuario