Robe REDBLINDER 2-48 Manual de usuario
version 1.0
2
3
Table of contents
1. Safety instructions ......................................................................................................... 4
2. Operating determinations.............................................................................................. 4
3.Description of the REDBlinder 2•48............................................................................... 5
4.Installation........................................................................................................................ 5
4.1.Connection to the mains ............................................................................................ 5
4.2 DMX-512 connection/connection between xtures .................................................... 6
4.3 Rigging the xture ...................................................................................................... 6
4.4 Fitting the frost lter....................................................................................................7
5.REDBlinder 2•48 - DMX protocol ,version 1.0............................................................... 8
6.REDBlinder 2•48- Control menu map .......................................................................... 10
7.Control board................................................................................................................. 11
7.1 Addressing the REDBlinder 2•48 ............................................................................. 11
7.2 Program running ...................................................................................................... 11
7.3 Manual mode ........................................................................................................... 12
7.4 Test sequences........................................................................................................ 13
7.5 Stand-alone mode.................................................................................................... 13
7.6 Special functions ...................................................................................................... 13
8.Technical Specications: ............................................................................................. 15
9.Maintenance................................................................................................................... 16
REDBlinder 2•48
4
CAUTION!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this product has to:
- be qualiled
- follow the instructions of this manual
CAUTION!
Be careful with your operations. With a high voltage you can suffer
a dangerous electric shock when touching the wires inside the unit!
This product has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the product.
Always ground the unit.
The electric connection, repairs and servicing must be carried out by a qualied employee.
Do not connect this unit to a dimmer pack.
Use a source of AC power that complies with local building and electrical rules.AC power has to have both
overload and short circuit protection.
CAUTION!
Avoid looking directly into the LED light beam at close range!
2. Operating determinations
This product was designed for indoor use only.
If the unit has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has
reached room temperature.
Avoid brute force when installing or operating the unit.
When choosing the installation-spot, please make sure that the unit is not exposed to extreme heat, moisture
or dust.
Only operate the unit after having checked that the housing is rmly closed and all screws are tightly fas-
tened.
The maximum ambient temperature 40° C must never be exceeded.
Operate the unit only after having familiarized with its functions. Do not permit operation by persons not quali-
ed for operating the unit. Most damages are the result of unprofessional operation!
Please use the original packaging if the product is to be transported.
Please consider that unauthorized modications on the unit are forbidden due to safety reasons!
5
3.Description of the REDBlinder 2•48
4.Installation
4.1.Connection to the mains
The REDBlinder 2•48 is equipped with auto-switching power supply that automatically adjusts to any 50/60 Hz
AC power source from 100-240 volts.
Connect the REDBlinder 2•48 to the mains with the power cord.
If the plug on the exible cord is not the right type for your socket outlets,do not use an adaptor,but remove the
plug from the cord and discard.Carefully prepare the end of the the supply cord and t a suitable plug.
The earth has to be connected!
Cord plug connections:
Cable (EU) Cable (US) Pin International
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
1 - Mounting yoke
2 - "T" bar
3 - LED modules
3
1
2
Control board
1 - 5-pin DMX output
2 - 3-pin DMX output
3 - 5-pin DMX input
4 - 3-pin DMX input
5 - LED display
6 - Mode-button
7 - Enter-button
8 - Up-button
9 - Down-button
10 - Fuse holder
11 - Mains input
6
4.2 DMX-512 connection/connection between xtures
The xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the xture or one xture with another.
DMX - output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-out-
puts, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always
connect one output with the input of the next xture until all xtures are connected.
Caution: At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ωresistor
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last xture.
Building a master/slave-chain:
Connect the DMX-output of the master xture in the data-chain with the DMX-input of the rst slave. Always
connect output with the input of the next slave until all slaves are connected (up to 9 xtures).
Caution:It’s necessary to insert the XLR termination plug (with 120 Ohm) into the input of the master xture
and into the output of the last slave xture in the link in order to ensure proper transmission on the data link.
4.3 Rigging the xture
Please consider the respective national norms during the installation!
The xture should be hung on a truss structure using a mounting clamp (not included).Mounting yoke has a 13
mm diamer hole for xing the mounting clamp.The xture can be tilted + - 180°.The required tilt angle of the
xture can be adjusted by means of the "T" bar on the side of the xture.
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
Master/slave operation
Controller operation
7
The installation must always be secured with a secondary safety attachment, e.g. an appropriate cord .Fasten
the safety cord through the mounting yoke and over the trussing system.
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert
before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
The xture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualications, do not attempt the installation yourself, but instead use a professional
structural rigger. Improper installation can result in bodily injury and.or damage to property.
If the xture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The
xture must never be xed swinging freely in the room.
Caution: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the xture!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the xture’s
weight.
Danger of re !
When installing the device, make sure there is no highly inammable
material in a distance of min. 0.5m.
CAUTION!
Make sure that the device is xed properly! Ensure that the
structure (truss)to which you are attaching the xtures is secure.
Instal the device in a ventilated location.Never cover air vents!
4.4 Fitting the frost ltr
The REDBlinder 2•48 is supplied with clear glasses covering LED modules. If you wish to use a diffusive light
, it is possible to order glass or lm frost lter sets and x them on the LED modules by two fastenig
screws.
Glass lters- soft frost light
Film lters-dense frost light
Fastening screws
Glass (lm) set
8
5.REDBlinder 2•48 - DMX protocol ,version 1.0
Mode/Channel Value Function Type of control
1 2 3 4
Zone 1
1 1 0-255
Red LEDs 1
Red LEDs saturation control (0-100%) proportional
2 2 0-255
Green LEDs 1
Green LEDs saturation control (0-100%) proportional
3 3 0-255
Blue LEDs 1
Blue LEDs saturation control (0-100%) proportional
Zone 2
4 4 0-255
Red LEDs 2
Red LEDs saturation control (0-100%) proportional
5 5 0-255
Green LEDs 2
Green LEDs saturation control (0-100%) proportional
6 6 0-255
Blue LEDs 2
Blue LEDs saturation control (0-100%) proportional
Common channels for all Zones
1 1 0-255
Red LEDs
All red LEDs saturation control (0-100%) proportional
2 2 0-255
Green LEDs
All green LEDs saturation control (0-100%) proportional
3 3 0-255
Blue LEDs
All blue LEDs saturation control (0-100%) proportional
7 4
0-7
8-15
16-23
24-31
32-39
40-47
48-55
56-63
64-71
72-79
80-87
88-95
96-103
104-111
112-119
120-127
128-135
136-143
144-151
152-159
160-167
168-175
176-183
184-191
192-199
200-207
208-215
216-223
224-231
232-239
240-247
248-255
MACRO SELECTION
No function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Macro 13
Macro 14
Macro 15
Macro 16
Macro 17
Macro 18
Macro 19
Macro 20
Macro 21
Macro 22
Macro 23
Macro 24
Macro 25
Macro 26
Macro 27
Macro 28
Macro 29
Mocro 30
Macro 31-rainbow effect from slow to fast
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
step
proportional
9
8 5
0-31
32-63
64-95
96-127
128-143
144-159
160-191
192-223
224-255
SHUTTER/STROBE
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences from slow to fast
Closing pulses in sequences from fast to slow
Shutter open
Random strobe-effects from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
9 6 0-255
DIMMER
Dimmer intensity from 0% to 100% proportional
Zone positions:
(every zone contains two LED modules)
10
6.REDBlinder 2•48 - Control menu map
Default settings=Bold print
A001 (001-504)
ProG
EPG.1
EPG.2
EPG.3
PrG.1
:
PrG.6
Auto (OFF,On)
Edit.
EPG.1
EPG.2
EPG.3
St.01
:
St.30
P.End
rEd (0-255)
:
dimr. (0-255)
F.tim.(0-255)
S.tim. (0-255)
COPY.
MAn.C.
rEd (0-255)
GrEE. (0-255)
bLuE (0-255)
:
MACr (0-255)
Stro. (0-255)
dimr. (0-255)
tESt
St.AL.
MASt.
EPG.1
:
PrG.6
SLA.
SPEC.
VErS.
tEMP
bALA. (On,OFF)
C.bAL.
rEd.b. (0..200..255)
GrE.b.(0..255)
bLu.b. (0..215..255)
dM.Pr.
Mod.1
Mod.2
Mod.3
Mod.4
i.bLi (On,Off
UPd.(no,YES)
Tabla de contenidos
Otros manuales de Equipo de iluminación de Robe
Robe
Robe Anolis ArcSource Outdoor 48 MC Integral RGBW Manual de usuario
Robe
Robe Anolis Eminere Classic 12 Manual de usuario
Robe
Robe Robin MiniMe Manual de usuario
Robe
Robe Robin T2 Manual de usuario
Robe
Robe Led Blinder 196 LT Manual de usuario
Robe
Robe CLUBSPOT 160 CT Manual de usuario
Robe
Robe Colormix 240 AT Manual de usuario
Robe
Robe Anolis Eminere Inground 2 Wireless DMX Manual de usuario
Robe
Robe ROBIN LEDBeam 350 RGBA Manual de usuario
Robe
Robe LightDome 575 Manual de usuario
Robe
Robe Anolis Ambiane XP56 Manual de usuario
Robe
Robe Color Wash 575E AT Manual de usuario
Robe
Robe Color Sport 1200 Profile Manual de usuario
Robe
Robe Robin DLX SPOT Manual de usuario
Robe
Robe PATT 2013 Manual de usuario
Robe
Robe DigitalSpot 5000 DT Manual de usuario
Robe
Robe Divine 160 RGBW Manual de usuario
Robe
Robe LiteWare HO Manual de usuario
Robe
Robe Robin Actor 3 Smart White Manual de usuario
Robe
Robe Robin BMFL FollowSpot Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
