Riva RC4100-1212-27 Manual de usuario

www.rivatech.de

Quick Installation Guide

This manual has been designed to guide you through basic settings of your IP devices, such as

installation and configuration for using them.

www.rivatech.de

Step1. Assemble and install IP camera

Before installation, DIP switches should be set to configure the camera ID, communication

protocol.

DIP2

ID Value

RS485

Terminatio

Not used

Protocol1

Protocol 2

Not used

Baud Rate

Pin3

Pin4

Protocol

Pin7

Pin8

BAUD RATE

OFF

Pelco-D or Pelco-P

OFF

Not Used

OFF

Not used

OFF

2400bps (Pelco-D)

OFF

Maxpro

OFF

4800bps (Pelco-P)

Not used

9600bps (Maxpro)

- Factory default of protocol is “Pelco-D, 2400 bps, 8 bit, 1 stop bit, no parity.”

Dip Switch

Lock Screw

Bubble

Ceiling Mount Bracket for indoor

Lock Holder

UNLOCK

DIP1 - Camera ID

DIP 2 - RS485, PTZ protocol, Baud rate

www.rivatech.de

SCREW (M3.0)

1. Find the places which are strong enough to support the camera, about 2kg.

2. Make a hole, Ø 147mm, on the ceiling.

3. Hook the safety wire to suspension and the safety wire hold on the bracket.

4. Install the ceiling mount bracket by driving 4 screws, Ø 4mm tapping screws.

CABLE TIE

LOCK HOLDER 2

MOUNT HOLDER

SAFETY WIRE

Ø 147.0 mm

COVER HOLE

LOCK HOLDER1

SAFETY WIRE HOLE

MOUNTING HOLE

CELING BRACKET

SCREW(Ø4.0)

5. You can make wires simple by cable ties.

6. Make the wires go through the square hole.

7. Insert mount holder and twist the camera counterclockwise.

www.rivatech.de

The camera may fall off the ceiling even after the proper installation

and mounting. To prevent any accident, make sure the ceiling is firm

and stable enough to support the camera. If any reinforcement is

needed, consult with your safety personnel and proceed with the

installation.

Caution

8. Fix the camera by driving a screw on lock holder1 and 2.

9. Install the cover by inserting cover lock and twisting clockwise.

COVER HOLE

COVER

LOCK HOLDER.2

10°

LOCK HOLDER.1

www.rivatech.de

Step2. Connect cables to IP device

Connect each cable to the device. To see the correct positions of all connectors, refer to the

following image below.

* Models herein and their appearance are subject to change without any prior notice.

AC220/110V

AC24V

ADAPTOR

IR SENSOR or DOOR SENSOR

D/O 2

D/O 1

MONITOR

TERMINAL BLOCK

(FEMALE)

LINE OUT

MIC/ LINE IN

100 BaseT

LINE OUT Reset button

MIC IN

LAN CABLE

www.rivatech.de

Step3. Set up network environment

The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP

address from the MAC address of your device. Please make sure the device and your PC are

on the same network segment before running the installation. If the network segment was

different between your PC and the device, change your PC’s settings as below.

IP address : 192.168.xxx.xxx

Subnet mask: 255.255.0.0

www.rivatech.de

Step4. View video on web page

View the live video on a web page using your IP device and its IP address. To have the correct

IP address ready and use it on a web page:

1. Convert a MAC address to an IP address. Refer to the Hexadecimal-Decimal Conversion

Chart at the end of this manual.

(The MAC address is attached on the side or bottom of the device.)

2. Open a web browser and enter the IP address of the device.

3. Click pop-up blocked and install the ActiveX setup.exe by clicking the Run or Save button.

You need to install the ActiveX for displaying the images.

4. Follow the instructions of the dialog boxes and complete the installation. Then the live video

is displayed on the main page of the web browser.

5. If the live video is not displayed with the message said,

“This software requires the

Microsoft XML Parser V6 or higher. Please download MSXML6 from the Microsoft

website to continue. Error code: Can not create XMLDOMDocument.”

, please download

and install the relevant MSXML.

* The explanation and captured images on this manual are mainly on the basis of Internet

Explorer 7.0.

MAC address = 00-13-23-01-14-B1 →IP address = 192.168.20.177

Convert the Hexadecimal number to Decimal number.

www.rivatech.de

Step5. Setting IP Address

To set up the Network configuration:

1. Click Setup on the upper right of the web page. The login page is displayed as below.

2. Enter the default user name (root) and the default password (pass), and then select OK.

3. Click System Options on the left of the Setup page, and then select TCP/IP from the drop-

down menu.

4. Input the data for the IP address configuration, and click the Apply button on the bottom of

the page.

To change the IP address, please make sure to check and have the correct Subnet mask and

Gateway ready. To use DHCP, select Obtain an IP address via DHCP.

To learn how to set up the web page for advanced configuration, refer to the Web Page

User's Manual, which is available on the SDK at the following path.

{SDK root}\DOC\

The default username

and password are:

root and pass.

www.rivatech.de

Advanced setup (IPAdminTool)

IPAdminTool is a utility program for IP products. Following list shows a part of features that

IPAdminTool provides.

Configure IP address, Subnet mask and Gateway

Shows network related information such as MAC address

Updates firmware

Reboots the device

IPAdminTool is provided with SDK at the following SDK path.

{SDK root}\BIN\TOOLS\AdminTool\

Rebooting

Reset can be carried out as follows:

1. While the device is in use, press and hold the Reset.

2. Release the Reset button after 3 seconds.

3. Wait for the system to reboot.

www.rivatech.de

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the Factory Default initialization.

To perform the Factory Default settings:

1. Disconnect the power supply from the device.

2. Connect the power to the device with the Reset button pressed and held.

3. Release the Reset button after 5 seconds.

4. Wait for the system to reboot.

More Information

To learn more about using other features of your devices, refer to the manual, which is

available on the SDK at the following path.

{SDK root}\DOC\

Tabla de contenidos

Otros manuales de Cámara de seguridad de Riva

Riva

Riva RC302SV-5117 Manual de usuario

Riva

Riva RC3702HD-5314 Manual de usuario

Riva

Riva RC100 Manual de usuario

Riva

Riva RC4602HD-6416 Manual de usuario

Riva

Riva RC100 Manual de usuario

Riva

Riva RC3302HD-5344 Manual de usuario

Riva

Riva RC3402HD-6211IR Manual de usuario

Riva

Riva RC5510 Manual de usuario

Riva

Riva RC3702HD-5314 Manual de usuario

Riva

Riva RC3102HD-5211 Manual de usuario

Riva

Riva RC3402HD-6211R Manual de usuario

Riva

Riva RC3500 Manual de usuario

Riva

Riva RC3402HD-6311IR Manual de usuario

Riva

Riva RC4602SV-7416A-30 Manual de usuario

Riva

Riva RC6602HD-5311 Manual de usuario

Riva

Riva RC3102HD-5311 Manual de usuario

Riva

Riva RC302HD-5117 Manual de usuario

Riva

Riva RC3502HD-5311 Manual de usuario

Riva

Riva RC8102HD-6111T Manual de usuario

Riva

Riva IPX5502HD-6415-05 Manual de usuario

Riva

Riva RC6702HD-6211 Manual de usuario

Riva

Riva RC 4602HD Manual de usuario

Riva

Riva RC3502HD-5211IR Manual de usuario

Riva

Riva RC4100-IN Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario