Riva RC3102HD-5311 Manual de usuario

www.rivatech.de

Quick Installation Guide

This manual provides instructions for quick installation and basic configuration of your IP device.

www.rivatech.de

Step1. Connect cables to IP device

Connect required cables to the device including the power cable and LAN cable. To see the

correct positions of all connectors, refer to the following image below.

The device is polarity sensitive. Incorrect power

connection may cause malfunction or damage to

the IP device.

Caution

Power Adaptor Connector (DC

12V)

* Model design and appearance are subject to change without any prior notice.

LAN

Cable

Output Configuration

buttons

Reset

Button

Power Cable

With PAL, NTSC

button

Clamping

Core

Clamping

Core

*This uses to prevent

electromagnetic

interference

*Reset and PAL/NTSC buttons are located under PCB.

Camera

from

vertical view

*Pressing the button

cycles through PAL,

NTSC, and no video

output mode:

No video

output -> PAL->NTSC

Video out is used only for

installation and works for

3 minutes when

PAL/NTSC button is

pushed.

www.rivatech.de

Step2. Install IP device

1) Place the installation template

(paper) that is included in the

package on the desired installation

surface.

2) Drill three holes in correct

positions based on the template

paper, and insert anchor blocks

into the holes.

3) Place the camera body and

match three alignment holes with

three anchor blocks. Fasten the

camera with screws.

4) Connect all the required cables

to the camera.

5) Adjust the lens position by referring

to the

Step 3. Set the lens position

6) Place the dome cover on the

main body of the camera. Dome

cover has three alignment holes

that match camera body’s

alignment holes.

7) Once properly placed, insert

alignment screws into the three

holes of the body and fasten them

up.

When assembling the main body of the camera and its dome cover,

make sure they fit each other into place.

To prevent products from damaging, place the camera on stable and non-

vibrating surfaces. If the surface is unstable, consult with safety personnel

for reinforcements first, and then proceed with the installation.

Caution

www.rivatech.de

Step3. Set the lens position

1) Remove the dome cover.

2) Adjust the lens to the desired position by manually moving its reinforced body,

upper lens shell, or horizontal platform in the following directions.

Connect to the web page of the device to see its real-time image. Refer to

step

Configuration

for details about using its web page.

3) Configure each setting of 6 buttons as below.

B. Pan the lens with

reinforced lower body

C. Tilt the lens with

horizontal platform

A. Rotate the lens

with upper lens shell

SW1

SW2

SW3

PAL/NTSC

TELE

WIDE

SW4

SW5

SW6

FAR

NEAR

Auto-

Focus

www.rivatech.de

Step4. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of

the device from converting the MAC address’s hexadecimal numbers, which is attached to the

device. Be sure that the device and PC are on a same area network before running the

installation.

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are

used, users may view the live streaming images on a web page using the device’s default IP

address:

1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal

Conversion Chart at the end of the manual.

(The MAC address of the device is attached on the side or bottom of the device.)

2. Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.

3. Web streaming and device configurations are supported through ActiveX program. When

the ActiveX installation pop-up window appears, authorize and install the ActiveX setup.exe.

MAC address = 00-13-23-01-14-B1 →IP address = 192.168.20.177

Convert the last two set of hexadecimal numbers to decimal numbers.

www.rivatech.de

Custom IP Environment

IPAdminTool and the manual are provided on USB stick or can download from www.rivatech.de

homepage.

IPAdminTool is a management tool, which automatically scans all of the network products for

users to perform administrative tasks, which includes network configurations, firmware update,

device reboot, and device organizations.

To modify the device’s default IP address for customized network area;

1. Find the device from the IPAdminTool’s list and highlight the device’s name.

2. Right-click the mouse and select “IP Address”; IP Setup window appears.

www.rivatech.de

3. In the IP Setup’s window, information under ‘Local Network information’ displays the

user/PC’s network area information. Those information need to be incorporated to the

IP Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP

Address, which are to be the unique numbers for the device. Refer to the image above

for the setting

4. Click ‘Setup’ to complete the modification. When the dialog box appears to request user

name and password, enter the default value for the administrator account (case-

sensitive) as below:

ID:

root

Password:

pass

PC environment Info

Give new unique IP address in

last two sets and mirror other

information in other boxes

www.rivatech.de

Step5. View video on web page

Once the device has the proper IP address, users can view the live streaming images

through a web browser.

The default username and password is

root / pass

1. When the device’s web address is accessed, the browser asks to install the ActiveX.

Click Allow.

2. Setup.exe installation link or pop-up window appears, depends on Microsoft® Internet

Explorer version. Proceed with rest of setup installation.

www.rivatech.de

3. Follow the instructions of the dialog boxes and complete the installation. Once the

installation is complete, start the web browser again and check if video stream is

displayed in the main view frame.

www.rivatech.de

Caution

If “

This software requires the Microsoft XML Parser V6 or

higher. Please download MSXML6 from the Microsoft

website to continue. Error code: Cannot create

XMLDOMDocument.

” message appears, download and

install the Microsoft Core XML Services (MSXML) 6.0.

Rebooting

Perform the following procedures to reset your device:

1. While the device is on, press the reset button for 1~2 seconds.

2. Wait for the system to reboot.

Resetting to the Factory Default Settings

When reset the device to the factory default setting, all parameters including the IP address

will be initialized.

To proceed back to the Factory Default reset:

1. While the device is on, press reset button and hold.

2. Release the Reset button after about 5 seconds when green LED blinks at rate of 200ms.

3. Wait for the system to reboot.

More Information

To learn more about using other features of your devices, refer to the manuals as “Web

Interface Manual” or “VCAsys _Online_Help”, which is available on USB stick or on

www.rivatech.de homepage.

Otros manuales para RC3102HD-5311

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Riva

Riva

Riva RC4100-1212-27 Manual de usuario

Riva

Riva RC6702HD-6211 Manual de usuario

Riva

Riva RC3202HD-6111 Manual de usuario

Riva

Riva RC362HD Manual de usuario

Riva

Riva RC3302HD-5344 Manual de usuario

Riva

Riva RC4602SV-7416A-30 Manual de usuario

Riva

Riva RC4202HD Manual de usuario

Riva

Riva RC8102HD-6111T Manual de usuario

Riva

Riva RC4100-IN Manual de usuario

Riva

Riva RC3202HD-6111W Manual de usuario

Riva

Riva RC3512HD-6311IR Manual de usuario

Riva

Riva RC3500 Manual de usuario

Riva

Riva RC6602HD-5311 Manual de usuario

Riva

Riva RC3500 Manual de usuario

Riva

Riva RC3102HD-5211 Manual de usuario

Riva

Riva RC4602HD-6416 Manual de usuario

Riva

Riva RC3500M Manual de usuario

Riva

Riva RC302SV-5117 Manual de usuario

Riva

Riva IPX5502HD-6415-05 Manual de usuario

Riva

Riva RC5502HD-6415-05 Manual de usuario

Riva

Riva RC5510 Manual de usuario

Riva

Riva RC3502HD-5311IR Manual de usuario

Riva

Riva RC4202HD Manual de usuario

Riva

Riva RC3202HD-6111 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario