RIOTEC DC9257AN Manual de usuario

1

Quick Guide

-DC9257AP (with Battery)

-DC9257AN (without Battery)

1 H92P/H92N

Connect to micro USB port of OTG device

2 H92P/H92N

3



* Before you use it, please switch to "C" for battery charge for

3~4 hours.

*Under “C mode”, you can raise/lower soft-keyboard easily.



H92P Scan Holder is with Li-Ion battery inside. When in

charging, please use the original power adaptor of

smartphone (recommend). Through it, it charges both OTG

device and H92P internal battery at the same time. When in

low battery (Red LED flashing), please charge it

immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

H92P’s battery.



The touch trigger is in the central area of mini scanner. (for both side).

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is fully charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and begin to scan

the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first. PL-2303 driver

can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can know which serial

port scanner connects to.

** The data you scan will be sent to serial port and your APP can get the

data from serial port directly.

Trigger

Area

Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

cable (OTG)

Mini

scanner

Micro USB

H92P with

Li- Ion Battery/

H92N without

Battery

Micro USB

LED Indicator

H92P only

O = Operation mode C = Char

e mode

LED Indicator

H92P only

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please from A1 to A7 for USB HID or B1 to B7 for USB

Serial. This will reset the scanner to its factory defaults.

USB HID USB Serial

A1 B1

A2 B2

A3 B3

A4 B4

A5 B5

A6 B6

A7 B7

Note: Please install PL-2303 driver for USB Serial.

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

Keyboard Language(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Japan

Denmark

Finland

France

Germany

Italy

Norway

1D Symbologies – 1

ENABLE

CODE 39 DISABLE

ENABLE

CODE 39

FULL ASCII

DISABLE

ENABLE

CODE 39 Transmit

Start/Stop Character DISABLE

ENABLE

UPC-E DISABLE

ENABLE

UPC-A DISABLE

ENABLE

Interleaved

25 DISABLE

ENABLE

Matrix

25 DISABLE

ENABLE

Industrial 25 DISABLE

ENABLE

CODE 93 DISABLE

3

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 2

ENABLE CODABAR DISABLE

ENABLE CODE 128

DISABLE

ENABLE

GS1-128

UCC/EAN-128

DISABLE

ENABLE MSI DISABLE

1D Symbologies – 3

ENABLE CODE 11 DISABLE

ENABLE

GS1-Databar

(RSS) DISABLE

ENABLE

GS1-Databar

(RSS-Limited) DISABLE

ENABLE

GS1-Databar

(RSS-Expand) DISABLE

ENABLE ISSN DISABLE

ENABLE ISBN DISABLE

ENABLE EAN-8

DISABLE

ENABLE EAN-13

DISABLE

Inter-Keystroke Delay (FOR USB HID Only)

This parameter specifies the delay between emulated keystrokes

No Delay Short Delay

(5ms)

Medium Delay

(10ms)

Long Delay

(15ms)

 Information in this document is subject to change without notice.

Q_200325_01

Este manual sirve para los siguientes modelos

Otros manuales de Lector de código de barras de RIOTEC

RIOTEC

RIOTEC iLS6300VBU Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6307LS Manual de usuario

RIOTEC

RIOTEC CR6327A Manual de usuario

RIOTEC

RIOTEC iDC9500 Manual de usuario

RIOTEC

RIOTEC DC9253AP Manual de usuario

RIOTEC

RIOTEC iDC9277A Manual de usuario

RIOTEC

RIOTEC iLS6308KBU Manual de usuario

RIOTEC

RIOTEC iCR6307ABM Manual de usuario

RIOTEC

RIOTEC DC9257LP Manual de usuario

RIOTEC

RIOTEC DC9270 Manual de usuario

RIOTEC

RIOTEC iDC9502K Manual de usuario

RIOTEC

RIOTEC iLS6302KS Manual de usuario

RIOTEC

RIOTEC DC9257L Manual de usuario

RIOTEC

RIOTEC FS5020E Manual de usuario

RIOTEC

RIOTEC FS5107A Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6300JS Manual de usuario

RIOTEC

RIOTEC iLS6302ABU Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6308KS Manual de usuario

RIOTEC

RIOTEC iLS6302J BQ Manual de usuario

RIOTEC

RIOTEC DC9257AP Manual de usuario

RIOTEC

RIOTEC iDC9507L Manual de usuario

RIOTEC

RIOTEC LS6300V Manual de usuario

RIOTEC

RIOTEC iLS6303XBU Manual de usuario

RIOTEC

RIOTEC iDC9608K Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario