RIOTEC DC9270D Manual de usuario

1

Quick Guide

- DC9270D

Connect to micro USB port of OTG device

* Before you use scanner, please switch to "C" for battery

charge for 3~4 hours.

* Under “C mode”, you can raise/lower soft-keyboard

easily. (For USB HID only)

DC9270D is with Li-Ion battery inside. When in charging,

please use the original power adaptor of OTG device

(recommend). Through it, it charges both OTG device and

DC9270D internal battery at the same time. When in low

battery (Red LED flashing), please charge it immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

DC9270D’s battery.



The touch sensor area is around the central area. There are 2

button triggers on the right and left side.

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is

fully charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and

begin to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first.

PL-2303 driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can

know which serial port scanner connects to.

** The data you scan will be sent to serial port and your

APP can get the data from serial port directly.

Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

cable (OTG)

Exit Windo

Li- Ion Battery

O=Operation mode

C=Charge mode

Indicator (LED)

Button Trigger

Touch Trigger Area

Button Trigger

Indicator

(

LED

)

Char

e por

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have

scanned the incorrect codes, please scan the “Default”

barcode. This will reset the scanner to its factory defaults.

(scan from A1 to A6 for USB HID, B1 for HID)

USB HID USB Serial

Note: Please install PL-2303 driver for USB Serial.

Keyboard Language (For USB HID only)

Scan the appropriate country code as below to program the

keyboard layout for your country or language. As a general

rule, the following characters are supported, but need special

care for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

ortu

Switzerland Hun

ary

Barcode Configuration Method:

Please follow the below 4 steps to complete the

"Symbologies Enable" or "Symbologies Disable"

1. Start Configuration

2. Choose one of 1D symbologies

3. Enable setting: scan Enable-1, then Enable-2

Disable setting: scan Disable-1, then Disable-2

4. End Configuration

Start

Configuration

1D Symbologies – 1

UPC-A UPC-E

EAN-13

(ISBN/ISSN)

EAN-8

Industrial

2 of 5

Matrix

2 of 5

Enable-1 Disable-1

Enable-2 Disable-2

End

Configuration

3

Barcode Configuration Method:

Please follow the below 4 steps to complete the

"Symbologies Enable" or "Symbologies Disable"

1. Start Configuration

2. Choose one of 1D symbologies

3. Enable setting: scan Enable-1, then Enable-2

Disable setting: scan Disable-1, then Disable-2

4. End Configuration

Start

Configuration

1D Symbologies – 2

Code 93

Code 11

MSI/Plessey

UK/Plessey

Codabar

Code 128

UCC/EAN 128

ISBT 128

1D Symbologies – 3

Code 39

(Code 32)

Interleaved

2 of 5

China Post GS1 DataBar

GS1 DataBar

Limited

GS1 DataBar

Expanded

Enable-1 Disable-1

Enable-2 Disable-2

End

Configuration

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_180504_01

Otros manuales de Lector de código de barras de RIOTEC

RIOTEC

RIOTEC OM7222J Manual de usuario

RIOTEC

RIOTEC FS5107A Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manual de usuario

RIOTEC

RIOTEC DC9252NP Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6307LS Manual de usuario

RIOTEC

RIOTEC OM722QJ Manual de usuario

RIOTEC

RIOTEC iDC9272N Manual de usuario

RIOTEC

RIOTEC LS6322A Manual de usuario

RIOTEC

RIOTEC iDC9502A Manual de usuario

RIOTEC

RIOTEC iLS6303XBQ Manual de usuario

RIOTEC

RIOTEC iLS6303XBU Manual de usuario

RIOTEC

RIOTEC DC9257L Manual de usuario

RIOTEC

RIOTEC iLS6303ABQ Manual de usuario

RIOTEC

RIOTEC FS5103A Manual de usuario

RIOTEC

RIOTEC iLS6302J/KBU Manual de usuario

RIOTEC

RIOTEC iLS6300FBQ Manual de usuario

RIOTEC

RIOTEC iDC9607L Manual de usuario

RIOTEC

RIOTEC iDC9607AW Manual de usuario

RIOTEC

RIOTEC iDC9602NW Manual de usuario

RIOTEC

RIOTEC iLS6300VBQ Manual de usuario

RIOTEC

RIOTEC FS5108J Manual de usuario

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manual de usuario

RIOTEC

RIOTEC OM7520M Manual de usuario

RIOTEC

RIOTEC iDC9608K Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario