RIOTEC DC9250KP Manual de usuario

1

Quick Guide

-DC9250KP (with Battery)

-DC9250KN (without Battery)

1 H92P/H92N

Connect to micro USB port of OTG device

2 H92P/H92N

3



* Before you use scanner, please switch to "C" for battery

charge for 3~4 hours.

*Under “C mode”, you can raise/lower soft-keyboard easily.



H92P Scan Holder is with Li-Ion battery inside. When in

charging, please use the original power adaptor of OTG

device (recommend). Through it, it charges both OTG

device and H92P internal battery at the same time. When in

low battery (Red LED flashing), please charge it

immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

H92P’s battery.



The touch sensor area is around the central area. (For both sides).

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is fully

charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and begin

to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first. PL-2303

driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can know which

serial port scanner connects to.

** The data you scan will be sent to serial port and your APP can

get the data from serial port directly.

Trigger Area

Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

port (OTG)

Mini

scanner

Micro USB

O = Operation mode C = Char

e mode

LED Indicator

H92PH only

LED Indicator

H92PH only

H92PH with

Li- Ion Battery/

H92NH without

Battery

2

Reset Configuration to Default :

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan A1~A14 for USB HID or B1~B13 for

RS232 / USB Serial. This will reset the scanner to its factory defaults.

USB HID

RS232/ USB serial



 

A4 B4 

 

A5 B5 

 

A6 B6 

 

A7 B7 

 

A8 B8 

 

A9 B9 

A10 B10 

 

A11 B11 

 

A12 B12 

 

A13 B13 

 

A14  

*Note : Please install PL-2303 driver for USB serial

Keyboard Country (FOR USB HID Only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

France

Italy

Spanish

German (Germany)

Portu

uese (Portu

al)

1D Symbologies – 1

ENABLE

CODE 93

DISABLE

ENABLE

CODE 128

DISABLE

ENABLE

GS1-128

DISABLE

ENABLE

UPC-A DISABLE

ENABLE

GS1

DataBar DISABLE

ENABLE

Code 11 DISABLE

ENABLE

MSI DISABLE

3

1D Symbologies – 2

ENABLE

CODABAR DISABLE

ENABLE

CODE 39 DISABLE

ENABLE

ISBN

DISABLE

ENABLE

UPC-E DISABLE

ENABLE

EAN 8 DISABLE

ENABLE

EAN 13

DISABLE

2D Symbologies

ENABLE PDF 417 DISABLE

ENABLE QR Code DISABLE

ENABLE Data Matrix DISABLE

ENABLE Aztec Code DISABLE

Inter-Keystroke Delay (For USB HID

Only)

This parameter specifies the delay between emulated

keystrokes

No Delay

(0ms)

(10ms)

(50ms)

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_190507_01

Este manual sirve para los siguientes modelos

Otros manuales de Lector de código de barras de RIOTEC

RIOTEC

RIOTEC iLS6300FBQ Manual de usuario

RIOTEC

RIOTEC iDC9277A Manual de usuario

RIOTEC

RIOTEC DC9257LP Manual de usuario

RIOTEC

RIOTEC iDC9607LW Manual de usuario

RIOTEC

RIOTEC iLS6302ABQ Manual de usuario

RIOTEC

RIOTEC OM7520M Manual de usuario

RIOTEC

RIOTEC LS6307L Manual de usuario

RIOTEC

RIOTEC iCR6300CBQ Manual de usuario

RIOTEC

RIOTEC iDC9608K Manual de usuario

RIOTEC

RIOTEC iLS6300JBQ Manual de usuario

RIOTEC

RIOTEC iDC9272A Manual de usuario

RIOTEC

RIOTEC iDC9507J Manual de usuario

RIOTEC

RIOTEC iDC9602NW Manual de usuario

RIOTEC

RIOTEC DC9270 Manual de usuario

RIOTEC

RIOTEC FS5102N Manual de usuario

RIOTEC

RIOTEC iDC9273A Manual de usuario

RIOTEC

RIOTEC iDC9602A Manual de usuario

RIOTEC

RIOTEC iLS6302J/KBU Manual de usuario

RIOTEC

RIOTEC LS6300 Manual de usuario

RIOTEC

RIOTEC iDC9607A Manual de usuario

RIOTEC

RIOTEC DC9257AN Manual de usuario

RIOTEC

RIOTEC OM7220J Manual de usuario

RIOTEC

RIOTEC LS6322A Manual de usuario

RIOTEC

RIOTEC iLS6307LBM Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario