RIOTEC DC9270 Manual de usuario

1

Quick Guide

- DC9270

Connect to micro USB port of OTG device

* Before you use scanner, please switch to "C" for battery

charge for 3~4 hours.

* Under “C mode”, you can raise/lower soft-keyboard

easily. (For USB HID only)

DC9270 is with Li-Ion battery inside. When in charging,

please use the original power adaptor of OTG device

(recommend). Through it, it charges both OTG device and

DC9270 internal battery at the same time. When in low

battery (Red LED flashing), please charge it immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

DC9270’s battery.



The touch sensor area is around the central area. There are 2

button triggers on the right and left side.

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is

fully charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and

begin to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first.

PL-2303 driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can

know which serial port scanner connects to.

** The data you scan will be sent to serial port and your

APP can get the data from serial port directly.

Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

cable (OTG)

Exit Windo

Li- Ion Battery

O=Operation mode

C=Charge mode

Indicator (LED)

Button Trigger

Touch Trigger Area

Button Trigger

Indicator

(

LED

)

Char

e por

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or

have scanned the incorrect codes, please scan the

“Default” barcode. This will reset the scanner to its

factory defaults. (scan from A1 for USB HID, B1 to B4

for USB Serial)

USB HID USB Serial

A1 B1

Note: Please install PL-2303 driver for USB Serial.

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

Abort

Configuration

End

Configuration

Multi-Interface Functions

LOUDER

SOUND

LEVEL MIDDLE

LOWER SILENT

LONG

SOUND /

LED CONTROL MIDDLE

SHORT

Multi-Interface Functions

DOUBLE CHECK

(ENABLE)

DOUBLE

CHECK

DOUBLE CHECK

(DISABLE)

SINGLE SCAN

READING

MODE

SINGLE SCAN

NO TRIGGER

Keyboard Language

DENMAR

FRENCH

GERMANY HUNGARY

JAPAN

ITALIAN

NORWEGIAN PORTUGAL

SPANISH

SWEDISH

SWITZERLAND USA

VIETNAM

3

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

Abort

Configuration

End

Configuration

1D Symbologies On/OFF - 1

ENABLE CODE 128 DISABLE

ENABLE CODABAR DISABLE

ENABLE

INTERLEAVE

25 DISABLE

ENABLE

INDUSTRIAL

25 DISABLE

1D Symbologies On/OFF – 2

ENABLE UPC-A DISABLE

ENABLE UPC-E DISABLE

ENABLE EAN-13 DISABLE

ENABLE

EAN-8 DISABLE

ENABLE MSI DISABLE

ENABLE

PLESSEY DISABLE

ENABLE CODE 11 DISABLE

ENABLE TELEPEN DISABLE

ENABLE CODE 39 DISABLE

1D Symbologies On/OFF – 3

ENABLE

CODE 32

ITALIAN PHARMACY DISABLE

ENABLE CODE 93 DISABLE

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_180504_01

Otros manuales de Lector de código de barras de RIOTEC

RIOTEC

RIOTEC LS6000B series Manual de usuario

RIOTEC

RIOTEC iDC9607AW Manual de usuario

RIOTEC

RIOTEC iLS6307JBQ Manual de usuario

RIOTEC

RIOTEC DC9257AP Manual de usuario

RIOTEC

RIOTEC LS6007 Manual de usuario

RIOTEC

RIOTEC iLS6302NBU Manual de usuario

RIOTEC

RIOTEC iDC9273A Manual de usuario

RIOTEC

RIOTEC iLS6300JB Manual de usuario

RIOTEC

RIOTEC OM722QJ Manual de usuario

RIOTEC

RIOTEC FS5107A Manual de usuario

RIOTEC

RIOTEC iLS6307LB Manual de usuario

RIOTEC

RIOTEC LS6300V Manual de usuario

RIOTEC

RIOTEC iDC9600KW Manual de usuario

RIOTEC

RIOTEC FS5027L Manual de usuario

RIOTEC

RIOTEC iLS6300JBU Manual de usuario

RIOTEC

RIOTEC iDC9607A Manual de usuario

RIOTEC

RIOTEC iDC9270J Manual de usuario

RIOTEC

RIOTEC RIOSCAN Manual de usuario

RIOTEC

RIOTEC iLS6308KBQ Manual de usuario

RIOTEC

RIOTEC iDC9602NW Manual de usuario

RIOTEC

RIOTEC iLS6302J/KBU Manual de usuario

RIOTEC

RIOTEC iDC9607L Manual de usuario

RIOTEC

RIOTEC iDC9607LW Manual de usuario

RIOTEC

RIOTEC iLS6300JBQ Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario