Rinnai Efficiency HD250i Manual de usuario

Rinnai New Zealand 1 HD250i Flueing Installation: 01-07

Rinnai New Zealand 1

RINNAI

HD250i Direct Flueing with Wall Terminal

Flueing Installation Instructions

This ue shall be installed in accordance with:

Manufacturer’s Installation Instructions

Local Gas Fitting Regulations

Municipal Building Codes

NZS:5261 Installation Code

Any other local relevant statutory regulation

This appliance and ue system must be installed, serviced and removed by an Authorised person.

•

Rinnai New Zealand 2 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Summary

Direct Flueing with Wall Terminal

For installations where the Rinnai Innity HD250i Internal is mounted directly on the inside of an

external wall.

The HD250i Direct Flue Kit (FFTL-10-200) can used to ue through walls 150-250mm thick (this

can not be extended).

Exhaust

Intake DIM Description DIM

(mm)

A Width 470

B Depth 220

C Height - Unit 600

D Height - Including Brackets 620

E Hot Water Outlet (from wall) 112 ~149

F Hot Water Outlet (from center) 61

G Cold Water Outlet (from wall) 94 ~135

H Cold Water Outlet (from center) 51

I Gas Connection (from wall) 56 ~96.5

J Gas Connection (from center) 110

KDistance between Flue Pipes 150

Positioning - Space Required

Inside Outside

Rinnai New Zealand 3 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Kit / Important

Direct Flueing - Kit Components

Flue Terminal Chamber Sleeve Condensate Proof Cover

Screw Kit (in actual kit, screw components are packaged in a clear plastic roll pack)

Important Installation Notes

The components of this ueing system CAN NOT BE CUT, use telescopic components to achieve the

required length

Ensure positioning of the ue terminal and ue installation comply with NZS:5261. The ue

products can reach temperatures above 200oC.

Flue must be supported and be independent of the appliance

Ensure the appliance can be removed without causing movement or displacement of the ue

Flue components are self-locking

The O-Rings in all the components are pre-greased, ensure they are not damaged when joining

When preparing the wall penetration, cover ue spigot to prevent debris from entering the

appliance

Before Installation

Wall hole diameter is Ø175mm or greater and is secure

That there is a 2o angled fall to the ue terminal

Length of sleeve tube has been checked, wall thickness can be 150 - 250mm thick

Distance to surroundings of the ue terminal as per NZS:5261

•

Screw (M4)

Tapping Screws (ø 3.8 x L32) Buttery Nuts (M5)

Trim Nut (M4)

Screw Plugs (#10)

Rinnai New Zealand 4 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Installation

Sealant Sleeve

Sealant

2ofall

Sleeve / Chamber Installation

Adjust sleeve length to thickness of wall allowing an additional 15mm (this is so it sits inside the

ue cowl) and secure sleeve to chamber with screw (B). Ensure you align sleeve and screw with

predrilled hole / slot.

Insert sleeve / chamber into wall and mark screw position where the sleeve will attach to the wall

Drill screw position and insert screw plugs

Fit sleeve plate with four screws ensuring spacer is positioned so there is a 2oangled fall

Apply plaster lling to gap between sleeve and wall and silicon sealant around the sleeve tube

•

Chamber

Buttery nuts

Sleeve

Spacer

Sleeve

Screw

Plug

Tapping

Screw

10-15mm

Sleeve

Rinnai New Zealand 5 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Installation

Flue Terminal Installation

Insert ue terminal into chamber so as the terminal is angled to fall

Fit terminal with condensate proof cover with trim nut and apply silicone sealant around ue

terminal

Within the condensate cover there is a wind buffer plate which can be congured to certain

positions if obstructions exist.

•

Twist to insert

Full thread screw

Condensate proof

cover

Trim nut Full thread screw

Left Obstruction Upper Obstruction

Wind Buffer Plate

Condensate Proof

Cover

Wind Buffer Plate

Condensate Proof

Cover

Right Obstruction

Condensate Proof

Cover

Wind Buffer Plate

Rinnai New Zealand 6 HD250i Flueing Installation: 01-07

Customer Contacts

For more information about buying, living and

servicing of Rinnai gas appliances call

0800 RINNAI (0800 746 624).

Rinnai New Zealand Limited

691 Mt Albert Road

PO Box 24068, Royal Oak, Auckland

Email: [email protected]

www.rinnai.co.nz

All Rinnai appliances meet or exceed the

safety standards required by New Zealand gas

and electrical regulations.

Rinnai is constantly improving its products

and as such specications are subject to

change or variation without notice.

RINNAI

HD250i Direct Flueing with Wall Terminal

PART NUMBER: 15246

Issue: A

Otros manuales para Efficiency HD250i

Tabla de contenidos

Otros manuales de Calentador de Rinnai

Rinnai

Rinnai RHFE-1004T Manual de usuario

Rinnai

Rinnai RCE-429A Guía de inicio rápido

Rinnai

Rinnai ES38 RHFE-1004RFA Guía de inicio rápido

Rinnai

Rinnai ASPIRATION RHFE-750ETR Manual de usuario

Rinnai

Rinnai RHFE-951ETR Manual de usuario

Rinnai

Rinnai ORH15SR Manual de usuario

Rinnai

Rinnai DD180 Hoja de especificaciones

Rinnai

Rinnai rhfe-556ftp Manual de usuario

Rinnai

Rinnai RHE1S40N Manual de usuario

Rinnai

Rinnai SPECTRUM 28 REH281 EB Manual de usuario

Rinnai

Rinnai Energysaver RHFE-556FM Manual de usuario

Rinnai

Rinnai Energysaver EX38C Manual de usuario

Rinnai

Rinnai INFINITY 16 Instrucciones de instalación

Rinnai

Rinnai Energysaver RHFE-556T Manual de usuario

Rinnai

Rinnai RHFE-551FT Manual de usuario

Rinnai

Rinnai RHFE-556FTR Hoja de especificaciones

Rinnai

Rinnai RCE-229A Guía de inicio rápido

Rinnai

Rinnai RCE-329A Manual de usuario

Rinnai

Rinnai ENERGYSAVER RHFE-308FTR Manual de usuario

Rinnai

Rinnai FC824 Manual de usuario

Rinnai

Rinnai RHFE-556 FM Manual de usuario

Rinnai

Rinnai REH-311FT(B) Manual de usuario

Rinnai

Rinnai Avenger 25 Manual de usuario

Rinnai

Rinnai ODHRAD3MN Hoja de especificaciones

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario