Right Weigh 310-PP Series Manual de usuario
ONBOARD LOAD SCALE
EXTERIOR ANALOG |310-PP SERIES
INSTALLATION & OPERATION MANUAL
2
WELCOME
Thank you for choosing to drive more and scale less! Here at Right Weigh, we are commied to
making our products simple to install and easy to use. If your vehicle configuraon is not described in
this manual, our technical support team is ready to answer your quesons!
+61 418 622840
rightweigh.com.au
IMPORTANT!
Please read instrucons COMPLETELY and thoroughly before installaon. Right Weigh, Inc. is not responsible or liable
for product failure or vehicle damage due to improper installaon. The installaon requirements are outlined in this
manual and should be followed thoroughly to avoid inaccuracy or damage to the product.
It is also important to be aware of vehicle manufacturer policies before making modificaons to the vehicle. Right
Weigh, Inc. is not liable or responsible for issues regarding warranes with other manufacturers. This is the
responsibility of the customer. If you are unsure about how these installaon pracces apply to your vehicle, please
contact your vehicle or component manufacturer.
3
Parts Required
Specificaons & Overview
Install
Calibrate
Operate & Weigh
Troubleshoot a Problem
Warranty Statement, Return Policy, & Repairs
4
5
7
10
11
12
15
CONTENTS
4
PARTS REQUIRED
These parts are sold separately in the 103-SK kit:
Male Branch Tee
The tube size should match the exisng suspension air line
1/4” Tube to Female NPT
The thread size and type should match the thread size and type of the male branch
tee
1/4” NPT to 1/4” Tube Elbow
1/4“ NPT to match the thread at the boom of the load scale
1/4” Air Line
The amount of air line needed depends on the mounng locaon of the gauge
5
SPECIFICATIONS & OVERVIEW
Technical Specificaons
Operang/Storage Temperature: -40° F to +185° F (-40° C to +85° C)
Enclosure: Black Polypropylene
Gauge Size: 3.5”
192 mm
216 mm
8.51”
7.56”
87 mm
2.97”
114 mm
114 mm
4.5”
4.5”
453 mm
17.84”
6
SPECIFICATIONS & OVERVIEW
The 310-PP series is designed for use on an axle group with a single height control valve suspension system.
Within this series, there are different products designed for different axle group configuraons. Before
installaon, make sure you have the proper gauge for your applicaon:
If you have the wrong gauge for your applicaon, please call our technical support listed on page 2.
*For use with large air bags (340mm or larger)
Suspension
Single Axle
Tandem Axle
Tri Axle
310-16KG-PP
310-25KG-PP
310-30KG-PP
*B310-30KG-PP
Gauge - Kilograms (KGS)
7
INSTALL
The 310 Series gauge comes in a protecve box. The following steps will walk you through how to correctly
mount and install the scale. Be sure to choose a locaon that is easily accessible and safe from potenal damage
(forkli posts, re caps, etc.)
DO NOT mount the scale directly to the chassis
or any other main beam unless it is approved by
the vehicle manufacturer. Doing so may void
the warranty with the vehicle manufacturer.
MOUNT SCALE
DUMP AIR FROM SUSPENSION SYSTEM
1
Choose a locaon to mount the scale that is easily accessible and safe from potenal damage (forkli
posts, re caps, etc.).
!
2
8
INSTALL
ASSEMBLE TEE FITTING
Choose a tee fing that matches the size of the exisng air line,
then install a female NPT tube fing onto the tee as shown. Use
teflon tape or equivalent to seal threads, ghten securely.
Cut the air line going to one of the air bags in the suspension group
to be monitored.
CUT EXISTING AIR LINE
3
4
INSTALL TEE FITTING
Insert the cut ends of the exisng air line and the new 1/4” air line
into the tee fing assembly as shown. Tighten all three tube nuts
securely.
5
INSTALL
9
ROUTE AIR LINE TO GAUGE
Route the new 1/4” air line from the tee fing to the gauge. Secure air line with zip es. Use 1/4” tube
to 1/4” NPT elbow fing to connect air line to gauge.
AIR UP SUSPENSION SYSTEM
Check for leaks and that all fing connecons are secure.
Pull red push/pull valve to check that air pressure is geng to the gauge.
6
7
10
CALIBRATE
1: The vehicle must be fully loaded. For best results, calibrate with a loaded weight within 1500lbs or 750kgs of
your typical axle group weight (DO NOT calibrate empty!)
2: Using a cerfied in-ground scale, obtain a loaded weight for the axle group aached to the gauge.
3: Park on a level surface. Shi the transmission to neutral and set the parking brakes.
4: Chock the wheels to prevent unexpected vehicle movement.
5: Release the parking brakes.
6: Make sure the Height Control Valve (HCV) has fully inflated the air bags. If needed, briefly dump the air from the
suspension and allow the HCV to refill the system.
7: Pull the red push/pull valve so that it is in the fully open posion.
8: Using a flathead screwdriver, turn the calibraon screw on the dial face unl the gauge matches the cerfied
axle group weight.
CALIBRATION
SCREW
PUSH/PULL
VALVE
Otros manuales para 310-PP Series
1
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Escala de Right Weigh
Right Weigh
Right Weigh 201-EBT-04B Manual de usuario
Right Weigh
Right Weigh 310-PP Series Manual de usuario
Right Weigh
Right Weigh 201-EBT-04 Manual de usuario
Right Weigh
Right Weigh 202-DDG-01 Manual de usuario
Right Weigh
Right Weigh 310-M3 Series Manual de usuario
Right Weigh
Right Weigh 201-EBT-01 Manual de usuario
Right Weigh
Right Weigh 510 Series Manual de usuario
Right Weigh
Right Weigh 201-EBT-01B Manual de instrucciones
Right Weigh
Right Weigh 201-219-10 Manual de usuario
Right Weigh
Right Weigh 201-EBT-01 Manual de usuario
Right Weigh
Right Weigh 201-EBT-04B Manual de usuario
Right Weigh
Right Weigh 510-46 Series Manual de usuario
Right Weigh
Right Weigh 201-RTS-01(B) Manual de usuario
Right Weigh
Right Weigh 201-EBT-02 Manual de usuario
Right Weigh
Right Weigh 201-EBT-02 Manual de usuario
Right Weigh
Right Weigh 201-EBT-01B Manual de usuario
Right Weigh
Right Weigh 201-EBT-01B Manual de usuario
Right Weigh
Right Weigh 202-DDG-0 Manual de usuario
Right Weigh
Right Weigh 201 Series Manual de usuario
Right Weigh
Right Weigh 201-EBT-01B Manual de uso y cuidado
