Right Weigh 201-EBT-02 Manual de usuario

ONBOARD LOAD SCALE

EXTERIOR DIGITAL |201-EBT-02(B)

LOW

WELCOME

Thank you for choosing to drive more and scale less! Here at Right

Weigh, we are commied to making our products simple to install

and easy to use. We understand that installaon can vary between

vehicles and yours may not be described in this manual. In any event,

our technical support team is ready to answer your quesons!

+61 418 622840

[email protected]

rightweigh.com.au

IMPORTANT!

Please read instrucons COMPLETELY and thoroughly before installaon. Right Weigh, Inc. is not

responsible or liable for any negave consequences as a result of improper installaon or

operaon including, but not limited to, product failure or damage that could aﬀect the integrity of

the vehicle.

The installaon steps in this manual are for the sole use of trained installers. Right Weigh, Inc.

accepts no responsibility or liability for issues involving, but not limited to, incorrect installaon

that occur from misinterpretaon of the steps outlined in this document.

It is the end user’s responsibility to be aware of vehicle manufacturer policies before making

modiﬁcaons to the vehicle. Right Weigh, Inc. is not liable or responsible for issues regarding, but

not limited to, warranes with other manufacturers. This is the responsibility of the end user.

For a more detailed explanaon of the the warranty and liability of Right Weigh, Inc. please refer

to the “Warranty Statement” and “Return Policy & Repairs” secon of this document and

www.rwls.com/warranty.

ONBOARD LOAD SCALE

EXTERIOR DIGITAL |201-EBT-02(B)

Speciﬁcaons & Overview

TCA Compliance Informaon

Scale Installaon and Electrical Connecons

Operang Modes

Tractor

Dedicated Tractor-Trailer Set

Trailer / Dolly

Calibraon & Unit of Measure

Security PIN Code

Set

Change

Operate & Weigh

Mobile Device Connecon

Maintenance

Troubleshoong

Appendix A - Addional Parts

Appendix B - Wiring Insulaon

Appendix C - Esmated Steer

Revision Log

Warranty Statement

Return Policy & Repairs

CONTENTS

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

and any use of such marks by Right Weigh, Inc. is under license. Other trademarks and trade

names are those of their respecve owners.

The Right Weigh 201-EBT-02(B) digital load scale has two internal air pressure

sensors. This scale will monitor one air suspension axle group with two Height

Control Valves (HCV) or two axle groups with one HCV each. An axle group

can be either a single, tandem, or triple set of axles on the truck or trailer.

SPECIFICATIONS & OVERVIEW

This load scale can be used to monitor one axle group with an air ride li axle if

the li axle air bags are controlled by the same height control valve as the other

axles in the group. The scale will need to be setup using mulple calibraon

mode. Refer to the Mulple Calibraon Mode (page 16) secon for more

informaon.

Drop Axle:

Independently regulated li axles cannot be considered part of an axle

group and must be in the UP posion when calibrang and weighing.

The 201-EBT-02B scale is not approved for use on vehicles with a

drop/li axle of any kind. For more informaon on TCA requirements,

refer to pages 7-8.

TCA OBM Requirement:

One Axle Group with 2 HCVs

2 HCVs

1 HCV 1 HCV

Two Axle Groups with 1 HCV Each

SPECIFICATIONS & OVERVIEW

The weight of the steer axle can be esmated if this scale is used to monitor a

tractor's drive axle group. Refer to Appendix C for more informaon.

Esmated Steer Axle:

The 201-EBT-02(B) scale has the capability of connecng to a remote sensor

that has been installed on a separate vehicle, most commonly used in drop &

hook situaons. For more informaon about this feature, please refer to the

separate 403-SK Installaon Instrucon Manual (PP-003-0084).

Remote Sensor Feature:

The Remote Sensor feature is not approved by TCA and must not be

enabled. For more informaon on TCA requirements, refer to pages 7-8.

TCA OBM Requirement:

Esmated Steer is for use on tractors with a ﬁh wheel hitch only, it

will NOT work on straight trucks or car haulers. Re-calibraon is

required aer changing the posion of a sliding ﬁh wheel.

To monitor the steer axle weight on a straight truck, you will need the

201-EBT-12B.

Operang Temperature: -22° F to +185° F (-30° C to +85° C)

Storage Temperature: -40° F to +185° F (-40° C to +85° C)

Power Requirement: 9 VDC to 32 VDC (Switched)

Units: Pounds (LBS) or Kilograms (KG)

Housing: High impact polycarbonate blend

Display: 0.8” LCD sunlight readable

POWER

ON/OFF

MENU/

ENTER

(1)

CAL HIGH (2)

CAL LOW (3)

DOWN ARROW

(4)

UP ARROW

62 mm

127 mm

406 mm

87 mm

184 mm

208 mm

114 mm

Technical Speciﬁcaons:

SPECIFICATIONS & OVERVIEW

TCA COMPLIANCE

INFORMATION

The 201-EBT-02B is a Transport Cerﬁcaon Australia (TCA) Type-Approved Mass

Sensor Unit (MSU) part of a Type-Approved On-Board Mass (OBM) system. This

organizaon approves automove technology that follows a set of guidelines to

ensure consumer safety and device reliability. For more informaon visit their

website at:

hps://tca.gov.au/publicaon/obm-system-speciﬁcaon/

The 201-EBT-02B is approved for use in both Category A and Category B

Type-Approved OBM systems. In order to comply with the TCA requirements, the

below guidelines MUST be followed:

OPERATING MODE

User must set the scale operang mode to either Sensor Average (AVG), Esmated

Steer + Sensor Average (S-AVG), Independent (IDP), or Independent + Esmated Steer

(S-IDP). Mulple Calibraon (4CAL) Mode does not comply with TCA requirements.

DROP AXLES

PIN CODE

CALIBRATION

INSTALLATION

The vehicle must not have a drop/li axle. TCA does not approve the use of this

system on vehicles with drop/li axles of any kind.

It is required that the authorized user/installer create a PIN code for the gauge to

ensure that the vehicle operator cannot tamper with the calibraon sengs. See

page 19 for informaon on how to set the PIN code.

The gauge must be calibrated before use and then re-calibrated at least once every 6

months. Each calibraon event must be recorded in the Calibraon Log (PP-003-0065

page 2).

Install the gauge using the guidelines set forth in this manual. Installaon Log

(PP-003-0065 page 1) must be completed at the me of installaon. The MSU

MUST be connected to a switched power source that is on when the ignion is on.

See pages 9-12 of this manual for detailed installaon instrucons.

REMOTE SENSOR FEATURE

The Remote Sensor feature must be disabled. This feature is not is not approved by

TCA.

Guidelines for TCA Compliance: Category A & B

TCA COMPLIANCE

INFORMATION

MAINTENANCE

TELEMATICS DEVICE

The gauge must go through the maintenance check described on page 23 at least

every 6 months. Each maintenance event must be recorded in the Maintenance Log

(PP-003-0065 page 4).

The prime mover must have an approved telemacs device installed and the device

must be connected to the Right Weigh system.

MOBILE APP

It is required that the operator use a smart phone or tablet with a mobile app to

wirelessly connect to all MSU’s (gauges) on the vehicle. If the operator is driving a

vehicle with more than one MSU, the MSU’s must be added within the app in front to

back order. Bluetooth connecon must be maintained with all MSU’s on the vehicle in

order for the weight informaon to be considered valid. Please see page 22 for more

informaon about the app.

SECURITY SEALS

Security seal kit p/n 909-SSK must be used to secure the MSU to the vehicle at the

me of installaon. See instrucons included with security seal kit for speciﬁc

installaon requirements.

Guidelines for TCA Compliance: Category B Only

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

DUMP AIR FROM SUSPENSION SYSTEM

Security seal kit p/n 909-SSK must be used to secure the MSU to the vehicle.

For more informaon on TCA requirements, refer to pages 7-8.

TCA OBM Requirement (Category B only):

Be sure to choose a locaon that is easily accessible and safe from potenal damage

(forkli posts, re caps, etc.)

DO NOT mount the scale directly to the chassis or any other main

beam unless it is approved by the vehicle manufacturer. Doing so

may void the warranty with the vehicle manufacturer.

CHOOSE LOCATION

Mount the bracket in the chosen locaon

and install the gauge box to the bracket

using supplied hardware.

The 201-EBT-02 scale is designed to be mounted on the outside of a truck or trailer,

however it must sll be mounted in a protecve enclosure. A protecve box and

mounng bracket are included with the 201-EBT-02B.

Make sure to use BOTH supplied mounng bolts to secure the

bracket to the vehicle. Using only one bolt can result in a cracked

bracket and the scale falling oﬀ the vehicle.

ROUTE AIR LINE TO GAUGE

Route the new 1/4” air line from the tee ﬁng assembly to the gauge.

Secure air line with zip es. Insert the air line into the push-to-connect

ﬁng on the back of the gauge. DO NOT ROTATE THE AIR FITTING!

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

CUT EXISTING AIR LINE

Choose a tee ﬁng that matches the size of

the exisng air line, then install a female NPT

tube ﬁng onto the tee as shown. Use Teﬂon

tape or equivalent to seal threads, ghten

securely. For more informaon on the parts

needed for air line installaon, see Appendix A.

ASSEMBLE TEE FITTING

Cut the air line going to one of the air bags in

the suspension group to be monitored.

Insert the cut ends of the exisng air line and the

new 1/4” air line into the tee ﬁng assembly as

shown. Tighten all three tube nuts securely.

INSTALL TEE FITTING

The air ﬁngs on the back of the gauge are directly connected to the

internal circuit board. Applying ground(-) or posive(+9-32) voltage to

air ﬁngs will cause immediate air sensor failure!

REPEAT STEPS 3-6 WITH

SECOND HCV

A second air line should go from an air bag

connected to the second HCV to ﬁng B on the

back of the gauge.

For a dedicated tractor-trailer set, ﬁng A should

connect to the drive axle group and ﬁng B

should connect to the trailer axle group.

HCV 1

HCV 2

AIR BAG

Otros manuales para 201-EBT-02

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Right Weigh

Right Weigh

Right Weigh 201 Series Manual de usuario

Right Weigh

Right Weigh 201-EBT-04B Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de usuario

Right Weigh

Right Weigh 510 Series Manual de usuario

Right Weigh

Right Weigh 201-219-11 Manual de usuario

Right Weigh

Right Weigh 202-DDG-04 Manual de usuario

Right Weigh

Right Weigh 202-DDG-03 Manual de usuario

Right Weigh

Right Weigh 201-EBT-04 Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de instrucciones

Right Weigh

Right Weigh 201 Series Manual de usuario

Right Weigh

Right Weigh 310-PP Series Manual de usuario

Right Weigh

Right Weigh 201-257-01 Manual de usuario

Right Weigh

Right Weigh 201-EBT-01 Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de uso y cuidado

Right Weigh

Right Weigh 201-EBT-02 Manual de usuario

Right Weigh

Right Weigh 201-EBT-04 Manual de usuario

Right Weigh

Right Weigh 201-EBT-04B Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de usuario

Right Weigh

Right Weigh 310-M3 Series Manual de usuario

Right Weigh

Right Weigh 201-257-01 Manual de usuario

Right Weigh

Right Weigh 201-RTS-01(B) Manual de usuario

Right Weigh

Right Weigh 202-DDG-01 Manual de usuario

Right Weigh

Right Weigh 202-DDG-0 Manual de usuario

Right Weigh

Right Weigh 201-EBT-04B Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario