Right Weigh 202-DDG-04 Manual de usuario

ONBOARD LOAD SCALE

INTERIOR DIGITAL |202-DDG-04

WELCOME

Thank you for choosing to drive more and scale less! Here at Right

Weigh, we are commied to making our products simple to install and

easy to use. We understand that installaon can vary between vehicles

and yours may not be described in this manual. In any event, our

technical support team is ready to answer your quesons!

(503) 628-0838

(888) 818-2058 - Toll Free (USA ONLY)

+61 418 622840 - Australia & New Zealand

support@rwls.com

leigh@rwlsau.com.au - Australia & New Zealand

www.rwls.com/how-to-calibrate-install/

rightweigh.com.au - Australia & New Zealand

IMPORTANT!

Please read instrucons COMPLETELY and thoroughly before installaon.

Right Weigh, Inc. is not responsible or liable for product failure or vehicle

damage due to improper installaon. The installaon requirements are

outlined in this manual and should be followed thoroughly to avoid inaccuracy

or damage to the product.

It is also important to be aware of vehicle manufacturer policies before making

modiﬁcaons to the vehicle. Right Weigh, Inc. is not liable or responsible for

issues regarding warranes with other manufacturers. This is the responsibility

of the customer. If you are unsure about how these installaon pracces apply

to your vehicle, please contact your vehicle or component manufacturer.

Speciﬁcaons & Overview

Scale Installaon & Electrical Connecons

Air Sensor Conﬁguraon

Changing Air Sensor Names

Esmated Steer Mode

Units / Display Sengs

Calibraon

Operang & Weighing

Security PIN Code

Reset Calibraon Data

Factory Default

Troubleshoong

Appendix A - Addional Parts (Tractor Suspension Installaon)

Appendix B - Addional Parts (Trailer Suspension Installaon)

Warranty Statement

Return Policy & Repairs

CONTENTS

SPECIFICATIONS & OVERVIEW

The Right Weigh 202-DDG-04 digital load scale has four internal air pressure

sensors. This scale can monitor either:

• two axle groups with two HCVs each

• one axle group with two HCVs + two axle groups with one HCV each

• four separate axle groups with one HCV each

• one axle group with four HCVs

Example of two axle groups with two HCVs each:

Example of four axle groups with one HCV each:

Example of one axle groups with two HCVs and two axle groups with one

HCV each:

1 HCV 1 HCV 1 HCV 1 HCV

Example of one axle groups with four HCVs:

1 HCV

2 HCVs

4 HCVs

2 HCVs 2 HCVs

Technical Speciﬁcaons

Operang Temperature: -4° F to +185° F (-20° C to +85° C)

Storage Temperature: -4° F to +185° F (-20° C to +85° C)

Power Requirement: 9 VDC to 32 VDC (Switched)

Units: Pounds (LBS) or Kilograms (KG)

Housing: ABS/PC Blend

Display: Capacitave Touch

SPECIFICATIONS & OVERVIEW

2.5”

2.4”

63 mm

60 mm

0.6”

2.6”

2.0”

15 mm

51 mm

65 mm

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

CHOOSE MOUNTING LOCATION

The gauge can be mounted in the dash panel either using an exisng factory

gauge hole or by creang one. If this opon is unavailable or not desirable,

Right Weigh has an oponal bracket (202-BR) that can be purchased

separately to mount the gauge. See below for a detailed list of opons for

mounng into the dash:

The 202-DDG-04 scale is designed to be mounted inside the vehicle cabin, it is

not for outdoor use. The following steps will walk you through how to correctly

mount and install the gauge.

Use an available 2 1/16”(52mm) factory

gauge hole.

Remove and replace a factory installed

drive axle air suspension pressure

gauge.

Cut a new hole in the dash panel using a

2 1/16” (52mm) hole saw as shown.

Make sure to check behind the dash

panel for internal wires and components

that may need to be moved to avoid

damage.

Use Right Weigh 202-BR bracket or an aermarket bracket to

mount the gauge.

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

CONNECT TO POWER AND GROUND

Connect the wiring harness to power and

ground. Be sure the RED wire is connected to

a SWITCHED posive (+) power source (DO

NOT CONNECT DIRECTLY TO BATTERY) and

the BLACK wire to chassis ground (-). Supply

voltage must be between 9 and 32 volts DC.

DO NOT connect directly to a baery or any constant power

source, gauge should be connected to a switched source so that

it can be disconnected from power when not in use. Most users

connect the power to the ignion switch.

INSERT 202 GAUGE

Insert the gauge into the mounng

hole or bracket. Hold the gauge in a

posion so the display appears level

on the dash panel or bracket. Note

that the thickest poron of the gauge

bezel indicates the boom of the

display. Screw the gauge nut onto the

back of the gauge unl it is ght.

TIGHTEN

INSERT

Connect the wire harness

to the connector on the

back of the gauge.

DUMP AIR FROM SUSPENSION SYSTEM

INSTALL BEZEL STYLING

COVER (OPTIONAL)

If desired, place chrome styling cover

over the front of the gauge bezel.

Press unl both sides snap into place.

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

ROUTE AIR LINE TO GAUGE

Route the new 1/4” air line from the

tee ﬁng assembly to the gauge.

Secure air line with zip es. Insert the

air line into the push-to-connect

ﬁng on the back of the gauge.

RE-ASSEMBLE DASH PANEL IF NEEDED

AIR UP SUSPENSION TO CHECK FOR LEAKS

INSTALL NEW STREET TEE FITTING

Install a new 1/4” air line and ﬁng into

the remaining port on the tee.

Air Bag

Street tee

tting

Air Bag

Insert a street tee ﬁng into the top of the

air bag that matches the thread size of the

vehicle suspension. Reinstall the suspension

air line and ﬁng into the street tee. For

more informaon on the parts needed for air

line installaon, see Appendix A.

INSTALL NEW 1/4” AIR LINE

Remove the suspension air line ﬁng from

the top of one of the air bags.

REPEAT STEPS 6-8 ON SECOND, THIRD,

AND FOURTH HCVS OR AXLE GROUPS

AIR SENSOR CONFIGURATION

The 202-DDG-04 gauge has four internal air pressure sensors and can be used to

monitor up to four separate axle groups with one Height Control Valve (HCV)

each, or a combinaon of of axle groups with a total of four HCVs. Follow the

steps below to conﬁgure the gauge to your applicaon:

Home

Weight

System Setup

Calibration

Settings

Units

Display Settings

Settings

Cong Names

From the Home screen, select the

WRENCH icon.

From the System Setup screen, select

SETTINGS.

Cong Inputs

Settings

User Cong

Average All

Sensor Mode

From the Sengs screen, select

the RIGHT ARROW. If monitoring

an axle group with four HCVs, all

four air sensors must be set to

Average together. If this is the

case, select AVERAGE ALL. If you

have more than one axle group

being monitore, select USER

CONFIG and then select the

RIGHT ARROW to connue to

the next screen.

Select CONFIG INPUTS.

AIR SENSOR CONFIGURATION

= Average

= Independent

Example: Air sensors 1

and 2 are averaged

together and sensors 3

and 4 are measured

independently

Cong Inputs

1 2

Example: All air sensors

are measured

independently from one

another

Cong Inputs

1 2

Cong Inputs

1 2

Example: Air sensors 1

and 2 are averaged

together and sensors 3

and 4 are averaged

together as well

If monitoring an axle group with two HCVs, the air lines from this

group MUST be connected to two adjacent air sensors, such as

sensors 1 and 2 or sensors 3 and 4, so they can be averaged

together. Sensors 2 and 3 and sensors 1 and 4 CANNOT be

averaged together.

If monitoring an axle group with two Height Control Valves (HCVs), the two air

sensors connected to that axle group must be set to Average together. For any axle

groups with one HCV, the sensor for that group must be set to be Independent from

the rest. To set the desired conﬁguraon, select the blue buons between the

numbers (air sensors 1, 2, 3, and 4) unl each is set correctly for your applicaon.

Tabla de contenidos

Otros manuales de Escala de Right Weigh

Right Weigh

Right Weigh 510-46 Series Manual de usuario

Right Weigh

Right Weigh 201-EBT-04 Manual de usuario

Right Weigh

Right Weigh 202-DDG-0 Manual de usuario

Right Weigh

Right Weigh 201-257-01 Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de uso y cuidado

Right Weigh

Right Weigh 310-PP Series Manual de usuario

Right Weigh

Right Weigh 310-M3 Series Manual de usuario

Right Weigh

Right Weigh 201-EBT-04 Manual de usuario

Right Weigh

Right Weigh 201-EBT-02 Manual de usuario

Right Weigh

Right Weigh 201-219-11 Manual de usuario

Right Weigh

Right Weigh 201-EBT-01 Manual de usuario

Right Weigh

Right Weigh 201-RTS-01(B) Manual de usuario

Right Weigh

Right Weigh 201-EBT-01 Manual de usuario

Right Weigh

Right Weigh 201-EBT-04B Manual de usuario

Right Weigh

Right Weigh 201-EBT-04B Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de usuario

Right Weigh

Right Weigh 201-EBT-02 Manual de usuario

Right Weigh

Right Weigh 202-DDG-02 Manual de usuario

Right Weigh

Right Weigh 201 Series Manual de usuario

Right Weigh

Right Weigh 310-PP Series Manual de usuario

Right Weigh

Right Weigh 201-EBT-01B Manual de instrucciones

Right Weigh

Right Weigh 201-EBT-01B Manual de usuario

Right Weigh

Right Weigh 201 Series Manual de usuario

Right Weigh

Right Weigh 202-DDG-03 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario