REED ST-332 Manual de usuario

reedinstruments

www com

Model ST-332

400A

AC/DC

Clamp Meter

Instruction

Manual

reedinstruments

www com

Table Of Contents

Safety .........................................................................................3-4

Meter Description.......................................................................... 5

Specications.............................................................................6-7

Operating Instructions..............................................................8-11

AC/DC Current Measurements ................................................... 8

DC/AC Voltage Measurements.................................................... 8

Resistance & Continuity Measurements ...................................... 9

Diode Measurements.................................................................. 9

Capacitence Measurements ....................................................... 9

Frequency or % duty cycle measurements ................................ 10

Data Hold ................................................................................. 10

Backlight................................................................................... 10

Zero Button............................................................................... 10

Manual Ranging........................................................................ 11

Battery Replacement ................................................................ 11

reedinstruments

www com

Safety

International Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates

the user must refer to the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal

use, hazardous voltages may be present

Double insulation

Safety Notes

• Do not exceed the maximum allowable input range of any function

• Do not apply voltage to meter when resistance function is selected.

• Set the function switch OFF when the meter is not in use.

Warnings

• Set function switch to the appropriate position before measuring.

• When measuring volts do not switch to current/resistance modes.

• Do not measure current on a circuit whose voltage exceeds 240V.

• When changing ranges using the selector switch, always disconnect the

test leads from the circuit under test.

• Do not exceed the maximum rated input limits.

Cautions

Improper use of this meter can cause damage, shock, injury or death.

Read and understand this user manual before operating the meter.

• Always remove the test leads before replacing the battery. Inspect the

condition of the test leads and the meter itself for any damage before

operating the meter.

reedinstruments

www com

Cautions con’t

• Repair or replace any damage before use.

• Use great care when taking measurements when the voltages are

greater than 25VAC rms or 35VDC. These voltages are considered a

shock hazard.

• Remove the battery if the meter is to be stored for long periods.

• Always discharge capacitors and remove power from the device under

test before performing Diode, Resistance or Continuity tests.

• Voltagechecksonelectricaloutletscanbedifcultandmisleading

because of the uncertainty of connection to the recessed electrical

contacts. Other means should be used to ensure that the terminals are

not “live”.

• Iftheequipmentisusedinamannernotspeciedbythemanufacturer,

the protection provided by the equipment may be impaired.

Input Limits

Function Maximum Input

A AC,A DC 400A

V DC, V AC, Frequency, Duty Cycle 600V DC/AC

Resistance, Diode, Continuity, Capacitance Test 250V DC/AC

reedinstruments

www com

Meter Description

1- Current Clamp

2- Clamp Trigger

3- Rotary Function Switch

4- LCD Display

5- ZERO Button

6- Data Hold and Backlight Button

7- Mode Select Button

8- Range Delect Button

9- Hz/% Duty Button

10- COM Input Jack

11- VΩ°C/°FJack

12- Battery Cover

Display Descriptions

1. DC Direct Currrent

AC Alternating Current

2. Minus Sign

3. 4000 Count

(0 to 3999)

Measurement Reading

4. AUTO AutoRange Mode

5. ZERO ZERO Mode

6. Diode Test Mode

7. Audible Continuity

8. HOLD Data Hold Mode

9. °C/°F, m, V, A, K, M, Ω Units of Measure List

reedinstruments

www com

Specifications

Function Range & Resolution Accuracy (% of reading)

DC Current

40.00 ADC 0~20.00ADC ± (2.5% + 6 digits)

20.00~40.00ADC ± (3% + 6 digits)

400.0 ADC 0~300.0ADC ± (2.5% + 6 digits)

300.0~400.0ADC ± (3.5% + 6 digits)

AC Current

40.00 AAC 0~20.00AAC ± (3% + 10 digits)

20.00~40.00AAC ± (5% + 10 digits)

400.0 AAC 0~300.0AAC ± (3% + 10 digits)

300.0~400.0AAC ± (5% + 10 digits)

DC Voltage

4.000 VDC ± (0.8% + 3 digits)

40.00 VDC ± (1.5% + 3 digits)

400.0 VDC

600 VDC ± (2.0% + 3 digits)

AC Voltage

400.0 mVAC ± (1.0% + 10 digits)

4.000 VAC

± (2.0% + 5 digits)40.00 VAC

400.0 VAC

600 VAC ± (2.0% + 5 digits)

Resistance

400.0Ω ± (1.0% + 4 digits)

4.000KΩ

± (1.5% + 2 digits)40.00KΩ

400.0KΩ

4.000MΩ ± (2.5% + 3 digits)

40.00MΩ ± (3.5% + 5 digits)

Capacitance

40.00nF ±(5.0% reading + 30 digits)

400.0nF ±(3.0% reading + 5 digits)

4.000µF ±(3.5% reading + 5 digits)

40.00µF

100.0µF ±(5.0% reading + 5 digits)

Frequency

5.000Hz ±(1.5% reading + 5 digits)

50.00Hz ±(1.2% reading + 2 digits)

Sensitivity: 5~5kHz:10Vrms min.

5kHz~150kHz:40Vrms min. @ 20%

to 80% duty cycle

500.0Hz

5.000kHz

50.00kHz

150.0kHz

Duty Cycle

0.5 to 99.0% ±(1.2% reading + 2 digits)

Pulse width: 100µs - 100ms, Frequency: 5Hz to 150kHz;

Sensitivity: 5~5kHz:10Vrms min.5kHz~150kHz:40Vrms min.

reedinstruments

www com

Specifications con’t

Clamp Size Opening 0.9” (23mm) approx

Diode Test Test current of 0.3mA typical;

Open circuit voltage 1.5V DC typical.

ContinuityCheck Threshold<150Ω;Testcurrent<1mA

Low Battery Indication “ ” is displayed

Overrange Indication “OL” is displayed

Measurements Rate 2 per second, nominal

InputImpedance 7.8MΩ(VDCandVAC)

Display 4000 counts LCD

AC Current 50/60Hz (AAC)

AC Voltage Bandwidth 50/400Hz (VAC)

OperatingTemperature 14to122°F(-10to50°C)

StorageTemperature -14to140°F(-30to60°C)

RelativeHumidity 90%(0°Cto30°C);75%(30°Cto40°C);

 45%(40°Cto50°C)

Altitude Operating: 3000m; Storage 10,000m

Over Voltage Category III 600V

Battery Two 1.5V “AAA” Batteries

Auto OFF approx. 30 minutes

Dimensions/Weight 200 x 50 x 35mm/200g

Safety

For indoor use and in accordance with Overvoltage

Category II, Pollution Degree 2. Category II includes

local level, appliance, portable equipment, etc., with

transient overvoltages less than Overvoltage Cat. III

reedinstruments

www com

Operation

NOTICE: Read and understand all warning and precaution state-

ments listed in the safety section of this operation manual prior

to using this meter. Set the function select switch to the OFF position

when the meter is not in use.

AC/DC Current Measurements

WARNING: Ensure that the test leads are disconnected from the meter

before making current clamp measurements.

1. Set the Function switch to the 400ADC, 40ADC, 400AAC or 40AAC

range. If the range of the measured is not known, select the higher

rangerstthenmovetothelowerrangeifnecessary.

Press the trigger to open jaw. Fully enclose one conductor to be measured.

3. The clamp meter LCD will display the reading.

DC/AC Voltage Measurements

1. Insert the black test lead into the negative COM terminal and the red

test lead into the positive Vterminal.

2. Set the function switch to the Vposition.

3. Select AC or DC with the MODE button.

4. Connect the test leads in parallel to the circuit under test.

5. Read the voltage measurement on the LCD display.

reedinstruments

www com

Resistance and Continuity Measurements

1. Insert the black test lead into the negative COM terminal and the red

test lead into the positive terminal.

2. Set the function switch to the Ωposition.

3. Use the multifunction MODE button to select resistance.

4. Touch the test probe tips across the circuit or component under test.

It is best to disconnect one side of the device under test so the rest of

the circuit will not interfere with the resistance reading.

5. For Resistance tests, read the resistance on the LCD display.

6.ForContinuitytests,iftheresistanceis<150Ω,atonewillsound.

Diode Measurements

1. Insert the black test lead banana plug into the negative COM jack and

the red test lead banana plug into the positive diode jack.

2. Turn the rotary switch to the position.

3. Press the MODE button until “ ” appears in the display.

4. Touch the test probes to the diode under test. Forward voltage will

indicate 0.4V to 0.7V. Reverse voltage will indicate “OL”. Shorted

devices will indicate near 0mV and an open device will indicate “OL”

in both polarities.

Capacitance Measurements

WARNING: To avoid electric shock, disconnect power to the unit

under test and discharge all capacitors before taking any capacitance

measurements. Remove the batteries and unplug the line cords.

1. Set the rotary function switch to the cap position.

2. Insert the black test lead banana plug into the negative (COM) jack.

Insert the red test lead banana plug into the positive (V) jack.

3. Touch the test leads to the capacitor to be tested.

4. Read the capacitance value in the display.

reedinstruments

www com

Frequency or % duty cycle measurements

1. Set the rotary function switch to the “VDC/AC,Hz/%” position.

2. Insert the black lead banana plug into the negative COM jack and the

red test lead banana plug into the positive V jack.

3. Select Hz or % duty with the Hz/% button.

4. Touch the test probe tips to the circuit under test.

5. Read the frequency on the display.

Data Hold

To freeze the LCD meter reading, press the data hold button. The data

hold button is located on the left side of the meter (top button). While data

hold is active, the HOLD display icon appears on the LCD. Press the data

hold button again to return to normal operation.

Note: The HOLD feature will activate when the Backlight is turned on.

Press the HOLD key again to exit Hold.

Backlight

Press and hold the HOLD the key for >1 second to turn on or off the

display backlight function.

Note: The HOLD feature will activate when the Backlight is turned on.

Press the HOLD key again to exit Hold.

Zero Button

For DCA and Capacitance Zero & Offset adjustment.

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario