REED R7100 Manual de usuario

Photo-Contact

Tachometer

Instruction

Manual

R7100

1.888.610.7664info@REED-Direct.com REED-Direct.com

Table of Contents

Introduction ................................................................................................... 3

Product Quality

.............................................................................................. 3

Safety ............................................................................................................ 3

Features

......................................................................................................... 3

Specications

................................................................................................ 4

Included

......................................................................................................... 5

Instrument Description .................................................................................. 5

Operating Instructions

................................................................................6-9

Applying Reﬂective Marking Tape ......................................................... 6

Photo Measurements ............................................................................... 6

Contact Measurements

............................................................................ 6

Surface Speed Measurements

................................................................. 7

Memory Recall ......................................................................................... 7

Accessing Maximum, Minimum and Last Values

..............................7-8

Accessing Stored Measurements

........................................................ 9

Battery Replacement..................................................................................... 9

Accessories and Replacement Parts ............................................................ 9

Applications

................................................................................................. 10

Product Care ............................................................................................... 10

Product Warranty ........................................................................................ 10

Product Disposal and Recycling ................................................................. 11

Product Support.......................................................................................... 11

1.888.610.7664info@REED-Direct.com REED-Direct.com

Introduction

Thank you for purchasing your REED R7100 Photo-Contact Tachom-

eter. Please read the following instructions carefully before using your

instrument. By following the steps outlined in this manual your meter will

provide years of reliable service.

Product Quality

This product has been manufactured in an ISO9001 facility and has been

calibrated during the manufacturing process to meet stated product

specications. If a certicate of calibration is required please contact the

nearest authorized REED distributor or authorized Service Center. Please

note an additional fee for this service will apply.

Safety

Never attempt to repair or modify your instrument. Dismantling your

product, other than for the purpose of replacing batteries, may cause

damage that will not be covered under the manufacturer’s warranty.

Servicing should only be provided by an authorized service center

Features

• Dualfunctionunitwithbothcontactandnon-contactcapabilities

• ProvidesfastandaccurateRPM(revolutionspermin)measurementsof

rotatingobjectsandsurfacespeedmeasurementsm/min(metersper

min)withincludedcontactadapters

• Built-inlaserpointeridentiestargetarea

• Internalmemoryrecallsmaximum,minimumvaluesaswellaslast

value stored

• LargeLCDdisplayandlowbatteryindicator

1.888.610.7664info@REED-Direct.com REED-Direct.com

Specifications

RPMRange(Contact): 0.5to19,999

RPMRange(Photo): 2.5to99,999

SurfaceSpeedRange: 0.05to1,999.9m/min

Resolution: Photo:0.1RPM(≤999.9)/1RPM(>1000)

 Contact:0.1RPM(≤999.9)/1RPM(>1000)

Surface:0.01m/min(≤99.99)/0.1m/min(>100)

BasicAccuracy: ±(0.05%+1dgt.)

General Speciﬁcations

VisibleIndicator: Yes(Laser)

TargetDistance: 1.6'(500mm)(Photo)

ResponseTime: <1sec

SamplingTime: 0.8sec(over60RPM)

DisplaySize/Type: 5DigitLCDDisplay

AutoShut-off: Yes

InternalMemory: Max,MinandLast

LaserClass: ClassIII

LowBatteryIndicator: Yes

PowerSupply: 4xAAbatteries

ProductCertications: CE

OperatingTemperature: 32to122°F(0to50°C)

StorageTemperature: -4to140°F(-20to60°C)

OperatingHumidity: 10to90%

Dimensions: 8.3x2.9x1.5"(210x74x37mm)

Weight: 7.9oz(224g)

1.888.610.7664info@REED-Direct.com REED-Direct.com

Included

• ReectiveTape

• LargeandSmallConeTipAdapters

• FunnelAdapter

• WheelAdapter

• Batteries

• MountingScrews

• HardCarryingCase

Instrument Description

1. Surface Wheel Adapter

2. ShaftExtensionwith

LargeConeAdapter

3. Contact Adapter

4. LaserSensor

(fornon-contactmeasurement)

5. MeasureButton

6. Function Switch

7. MemoryRecallButton

8. LCDDisplay

1.888.610.7664info@REED-Direct.com REED-Direct.com

Operating Instructions

Applying Reflective Marking Tape

1. Cutandpeeltheadhesivetapeprovidedintoapproximately0.5"

(12mm)squares.

2. Applyonesquaretoeachrotationshaft.

Thenon-reectiveareamustalwaysbegreaterthanthereectivearea.

4. Iftheshaftisnormallyreective,itmustbecoveredwithblacktape

orblackpaintbeforeattachingreectivetape.

5. The shaft surface must be clean and smooth before applying the

reectivetape.

Photo Measurements

1. Applyasmallpieceofreectivetapetotheobjectbeingmeasured.

2. Slidethefunctionswitchtothe"rpmphoto"position.

3. PresstheMeasurebuttonandalignthevisiblelightbeamwiththe

applied target.

Contact Measurements

1. Slidethefunctionswitchtothe"rpmcontact"position.

2. InstalltheproperRPMadapterforyourapplicationontheshaft.

3. PresstheMeasurebuttonwhilelightlypressingtherpmadapter

against the center opening of a rotating shaft.

4. ReleasetheMeasurebuttonwhenthereadingstabilizes

(approx.2seconds).

continued...

1.888.610.7664info@REED-Direct.com REED-Direct.com

Surface Speed Measurements

1. Slidethefunctionswitchtothe"m/mincontact"position.

2. Installthesurfacewheeladapterontheinstrument.

3. PresstheMeasurebuttonwhilelightlypressingthesurfacewheel

against the surface being measured.

4. ReleasetheMeasurebuttonwhenthedisplayreadingstabilizes

(approx.2seconds).

NOTE:Iftheinsidepartofthewheelisused(asshowninthe

picture),measurementsarerequiredtobemultipliedby0.9

for an accurate measurement. This will not be the case when

using the outside part of the wheel.

Memory Recall

Accessing Maximum, Minimum and Last Values

Themaximum,minimumandlastvaluesobtainedpriortoreleasingthe

Measurebuttonwillautomaticallybestoredinmemory.

IMPORTANT NOTE: All stored values will be erased from memory the

nexttimetheMeasurebuttonispressed.

continued...

Display

Reading

Max Value

Min Value

Last Value

Measuring Time

1.888.610.7664info@REED-Direct.com REED-Direct.com

Todisplaythesevalues,followthestepsbelow:

1. Press and hold the MEM button once. A value is displayed followed

bythe"UP"symbol,whichrepresentsthemaximumvalue.

2. ReleasetheMEM button.

3. Press and hold the MEM button again. A second value is displayed

followedbythe"dn"symbol,whichrepresentstheminimumvalue.

4. Release the MEM button.

5. Press and hold the MEM button again. A third value is displayed

followedbythe"LA"symbol,whichrepresentsthelastvalue.

6. Release the MEM button.

continued...

Max Value

DIGITAL TACHOMETER

Min Value

Last Value

RPM

DIGITAL TACHOMETER

RPM

DIGITAL TACHOMETER

RPM

DIGITAL TACHOMETER

RPM

DIGITAL TACHOMETER

RPM

DIGITAL TACHOMETER

RPM

1.888.610.7664info@REED-Direct.com REED-Direct.com

Accessing Stored Measurements

The meter has the capability of storing up to 64 values during a single

measuringperiod.Inordertorecallthesevalues,followthestepsbelow:

1. Press the MEM button four times and hold it down.

2. Themeterwillbegintocountdownfrom20to1RPMindicatingitis

compiling the stored values.

3. Once the countdown is completed, a total of the values stored

willdisplayas"AnXX",whereasXXwillbethenumberofstored

measurements.

Press the MEM button repeatedly to scroll through each stored value.

Battery Replacement

1. WhenthebottomleftcorneroftheLCDdisplays the batteries

should be replaced.

2. OpentheBatteryCoverlocatedonthebackofmeterandremove

the batteries.

3. Replace with 4 new AA batteries, check that the polarization is

correct and reinstall the cover.

Accessories and Replacement Parts

ST-TIPLLargeConeAdapter

ST-TIP Cone Adapter

ST-FUNNEL Funnel Adapter

ST-SHAFTShaftExtensionAdapter

ST-WHEEL Surface Wheel Adapter

RT100ReectiveTapeforTachometers

CA-05A Soft Carrying Case

Don'tseeyourpartlistedhere?Foracompletelistofallaccessoriesand

replacement parts visit your product page on www.reedinstruments.com.

1.888.610.7664info@REED-Direct.com REED-Direct.com

Applications

• Identifyissueswithrotationalequipmentsuchas:Conveyors,Turbines,

Compressors, Fans and Blowers.

• AutomatedAssemblyandProductionLines

Product Care

Tokeepyourinstrumentingoodworkingorderwerecommendthefollowing:

• Storeyourproductinaclean,dryplace.

• Changethebatteryasneeded.

• Ifyourinstrumentisn’tbeingusedforaperiodofonemonthorlonger

please remove the battery.

• Cleanyourproductandaccessorieswithbiodegradablecleaner.Donot

spraythecleanerdirectlyontheinstrument.Useonexternalpartsonly.

Product Warranty

REED Instruments guarantees this instrument to be free of defects

inmaterialorworkmanshipforaperiodofone(1)yearfromdateof

shipment. During the warranty period, REED Instruments will repair or

replace, at no charge, products or parts of a product that proves to be

defective because of improper material or workmanship, under normal

use and maintenance. REED Instruments total liability is limited to repair

or replacement of the product. REED Instruments shall not be liable for

damages to goods, property, or persons due to improper use or through

attemptstoutilizetheinstrumentunderconditionswhichexceedthe

designed capabilities. In order to begin the warranty service process,

pleasecontactusbyphoneat1-877-849-2127orbyemailat

info@reedinstruments.com to discuss the claim and determine the appro-

priate steps to process the warranty.

1.888.610.7664info@REED-Direct.com REED-Direct.com

Otros manuales para R7100

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario