RAISE 3D N2 Manual de usuario
N2 N2 Plus
Quick Start Guide
N-Series 3D Printer
* Please review this entire guide before operating the printer.
N2 N2 Plus
N-Series 3D Printer
/ Quick Start Guide
AList of Parts
N2
Touch Screen
Nozzle(s)
Fan(s)
Z-Stage
Print Bed
Filament Feeder Z Ball Screws
Power Inlet
Power Switch
USB Storage &
SD Card Slot
N2 Plus
Touch Screen
Nozzle(s)
Fan(s)
Z-Stage
Print Bed
Filament Feeder Z Ball Screws
Power Inlet
Power Switch
USB Storage &
SD Card Slot
Wheels
GPIO Ports
GPIO Ports
N-Series 3D Printer
/ Quick Start Guide
BHardware Installation
Recommend to unclip the Zipties as you
are able to reuse the ties later.
1
3
Remove!
(×2) Hex Wrench
(3 mm)
Use the 3mm hex wrench to remove the Z
axis clamps on both Z axis ball screws.
The 3mm hex wrench is packed under the
printing platform.
Please remove the 24 clips holding the
extruder assembly in place before power-
ing on your printer. If you fail to remove
these clips your printer will be damaged.
Please save these clips and re-install them
if you transport your printer.
2
Remove!
(×24)
Remove!
Gently lift the build plate gently with
your hands and remove the accessory bag
under the build plate and open it for
standby. You can gently turn the ball screw
by hand to raise the z platform to help taking
out the accessory bag.
4
N-Series 3D Printer
/ Quick Start Guide
BHardware Installation (continued)
List of Contents
Spatula
Filament
(×1/×2)*
Filament Holder
(×1/×2)*
Nozzle
Cleaning Kit
Glass with
Protective Foam
Hex Wrenches
2.5mm 2mm 1.5mm3mm
Fan Cover
(×0/×2)*
Tweezers
USB Storage Other Accessories
(Spare)
Filament Guide
Tube (×2/×4)*
Fuse
15A
10A
Build Plate Clips Filament Guide
Tube Holder
Power Cable
* Due to the difference between single and dual extrusion machines, the quantity of some of the products
received will be different.
Besides, there is only one fan cover in the printer with single extruder and it is has already been equipped
to the printer.
N-Series 3D Printer
/ Quick Start Guide
BHardware Installation (continued)
Remove the remaining build plate clips
from the accessory box and secure them
to the glass and heated bed plate.
NOTE: The best distance between the glass clip
and the edge of print platform is 5cm.
10
5cm5cm
Gently slide the glass plate. Make sure it
snaps into the build plate clamps at the
back.
NOTE: Place the surface which posted with
BuildTak upwards, while the yellow label is at the
back left corner. Make sure it snaps into the build
plate clamps in this way.
9
Remove the glass build plate from the
protective foam.
8
Protective Foam
Cover Build Plate Remove!
N-Series 3D Printer
/ Quick Start Guide
BHardware Installation (continued)
The printer will go through a start-up
sequence. When the touch screen displays
"Home", the printer is ready.
10
Slide the starter box out of the base of the
printer.
Remove the power cable from the starter
box and plug the machine into a wall
outlet.
9
Install the filament holder in the mounting
hole on the side of the printer and place a
spool of filament on the holder.
NOTE: The filament should load clockwise.
A B
C D
8Mounting
holes
N-Series 3D Printer
/ Quick Start Guide
BHardware Installation (continued)
Feed the filament through the guide tube.
13
14 Push the filament down to the feed gear
until the gear grips the filament.
NOTE: For your first set of prints please use the
left nozzle only. The printer has been pre-cali-
brated based on printing with the left nozzle in
the factory. If you want to print with the right
nozzle or dual extrufers, please follow the
instructions on aligning both extruders found
here: https://www.raise3d.com/pages/faq.
Press the “Utilities” menu on the screen and
set the temperature of the left nozzle for
the filament, then press the “Load” button.
Finish the feeding operation step by step
according to the instructions on the screen.
NOTE: This document is set based on the Raise3D
PLA filament, which is delivered together with the
printer. Therefore we advise that you use this PLA
for testing.
12
N-Series 3D Printer
/ Quick Start Guide
CideaMaker Installation
Open the installer and choose the language. Set a path for installing ideaMaker then
click "Next".
1
The ideaMaker software is
available on the USB storage
included with your printer.
Or go to www.raise3d.com and
download the ideaMaker
software.
www.raise3d.com
Download ideaMaker
WINDOWS
N-Series 3D Printer
/ Quick Start Guide
Click "Finish" and ideaMaker is installed.
Follow the instructions and click "Install". After the installation is finished, click "Next" to
go to the next step.
2
3
CideaMaker Installation (continued)
N-Series 3D Printer
/ Quick Start Guide
CideaMaker Installation (continued)
Open the Disk Image for the ideaMaker installed on the USB storage included with your
printer or that you downloaded from www.raise3d.com.
MAC OS X
Otros manuales para N2
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Impresora 3D de RAISE 3D
RAISE 3D
RAISE 3D E2 Manual de usuario
RAISE 3D
RAISE 3D E2 Manual de usuario
RAISE 3D
RAISE 3D Pro2 Series Manual de usuario
RAISE 3D
RAISE 3D PRO2 Series Manual de usuario
RAISE 3D
RAISE 3D Pro3 Series Manual de usuario
RAISE 3D
RAISE 3D Pro2 Series Manual de usuario
RAISE 3D
RAISE 3D PRO2 Series Manual de usuario
RAISE 3D
RAISE 3D E2CF Manual de usuario
RAISE 3D
RAISE 3D Pro2 Series Manual de usuario
RAISE 3D
RAISE 3D E2 Manual de usuario
RAISE 3D
RAISE 3D E2 Manual de usuario
RAISE 3D
RAISE 3D PRO2 Series Manual de usuario
RAISE 3D
RAISE 3D PRO2 Series Manual de usuario
RAISE 3D
RAISE 3D N-Series Manual de usuario
RAISE 3D
RAISE 3D Pro2-401 Manual de usuario
RAISE 3D
RAISE 3D E2 Manual de usuario
RAISE 3D
RAISE 3D Pro2 Series Manual de usuario
RAISE 3D
RAISE 3D PRO2 Series Manual de usuario
RAISE 3D
RAISE 3D Bondtech Dual Extruder Manual de usuario
RAISE 3D
RAISE 3D Pro2 Series Manual de usuario
