Quantum StorNext QM1200 Manual de usuario

StorNext QM1200, QS1200 or QS2400 Base System

Replacing a Controller Battery

6-68009-01 Rev B *6-68009-01 B*

ii Replacing a Controller Battery

StorNext QM1200, QS1200 or QS2400 Base System, Replacing a Controller Battery, 6-68009-01 Rev B, April 2015,

Product of USA.

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including

but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation

may revise this publication from time to time without notice.

Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written

authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.

TRADEMARK STATEMENT

Quantum, the Quantum Logo, Backup. Recovery. Archive. It's What We Do., Be Certain, Be Quantum Certain, DLT, the DLT

Logo, DLTSage, DLTtape, the DLTtape Logo, DXi, DXi Accent, Dynamic Powerdown, FastSense, FlexLink, GoProtect,

GoVault, iLayer, Lattus, MediaShield, Optyon, Pocket-sized., Well-armored., Preserving the World's Most Important Data.

Yours., Q-Cloud, Quantum Certain, Quantum Certainty, Quantum vmPRO, Scalar, SDLT, SiteCare, SmartVerify,

StorageCare, StorNext, Super DLTtape, SuperLoader, and Vision are either registered trademarks or trademarks of

Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property

of their respective owners.

Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their

respective companies. All other brand names or trademarks are the property of their respective owners.

Quantum specifications are subject to change.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 1 -

Replacing a Controller Battery in the StorNext QM1200, QS1200 or

QS2400 Base System

You can determine whether you have a failed controller battery in two ways:

The Recovery Guru directs you to replace a failed controller battery.

The blue Battery Service Action Required LED indicates a failed controller battery.

Before you start this procedure, gather antistatic protection and a replacement controller battery.

Read through all of the following steps in this procedure before you start to replace the controller battery.

1. Gather support data about your storage array by using one of these methods:

—Use the storage management software to collect and save a support bundle of your storage array. From the

Array Management Window, click Monitor >> Health >> Collect Support Data. Then name and specify a

location on your system where you want to store the support bundle.

—Use the command line interface (CLI) to run the save storageArray supportData command to

gather comprehensive support data about the storage array. For more information about this command, see

Command Line Interface and Script. Running this command can temporarily impact performance on your

storage array.

2. Did the Recovery Guru direct you to replace a failed controller battery?

—Yes – Go to Step 3.

—No – Run the Recovery Guru to identify the failed component, and go to Step 3.

3. Put on antistatic protection.

4. Unpack the new controller battery.

a. Set the new controller battery on a flat, static-free surface near the base system.

b. Save all the packing materials in case you need to return the controller battery.

Removing and Replacing the Failed Controller Battery

Refer to the following sections to remove and replace the failed controller battery.

Locating Failed Controller Battery

Removing the Controller from the Array

Replacing the Battery in the Controller

Reinstalling the Controller into the Array

Locating Failed Controller Battery

1. Locate the failed battery by checking the Battery Service Action Required LEDs on the array controller.

ATTENTION Possible hardware damage – If you perform this procedure with the power turned on, the

equipment might overheat if the controller slot is left open for more than three minutes. To prevent the

possibility of overheating, you must insert the controller air blocker into the empty controller slot when you

service the controller.

ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper

antistatic protection when handling tray components.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 2 -

2. Refer to Figure 1 to locate the controllers within the array (representative array provided).

Figure 1 Controller Location

1. Controller Canister A

2. Drive Expansion

3. Controller Canister B

4. Drive Expansion

3. Refer to Figure 2 to locate the controller with a battery fault.

If a battery fault is detected, the amber Battery Service Action Required LED is on.

Figure 2 Battery Service Action Required LED on the Controller

1. Battery Service Action Required LED (Amber)

Removing the Controller from the Array

1. Label each copper cable or fiber-optic cable that is attached to the controller canister with the failed battery so

that you can reconnect each cable correctly after the controller canister is reinstalled.

2. Record the information from the seven-segment display on the base system.

The display flashes a sequence of codes. To find information about the displayed diagnostic codes, refer to

StorNext Q-Series Storage Install Guide.

Use either the GUI (first bullet) or the CLI (second bullet) to take the appropriate controller offline.

—From the Hardware pane in the Array Management Window, right-click the picture of the controller that you

want to take offline, and select Advanced >> Place >> Offline.

ATTENTION Potential degraded performance – To prevent degraded performance, do not twist, fold,

pinch, or step on the cables. Many cables have a minimum bending radius. For example, do not bend

fiber-optic cables tighter than a 5-cm (2-in.) radius. Check the specifications for your cables, and do not

bend any cable tighter than the minimum specified radius.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 3 -

—Run the following command:

SMcli <DNS-network-name-or-IP-address> -c “set controller [(a | b)]

availability=offline”;

If necessary, wait for the Controller Service Action Allowed LED to come on. This indication might take several

minutes for a large configuration. See Figure 3.

Figure 3 Controller LEDs

1. Host Link 1 Service Action Required LED (Green)

2. Host Link 2 Service Action Required LED (Green)

3. Battery Service Action Required LED (Amber)

4. Controller Service Action Allowed LED (Blue)

5. Controller Service Action Required LED (Amber)

3. Disconnect all interface cables (drive connections, host connections, and Ethernet connections) from the

controller canister that has the failed battery.

If the storage array is running while you perform the controller battery replacement, do not disturb the second

controller canister.

4. Prepare the controller air blocker (Figure 4) by removing it from the packaging and folding it inward at right

angles so it is ready to insert into the open controller slot.

NOTE If Small Form-factor Pluggable (SFP) transceivers are present, you do not need to remove them

from the controller canister when replacing the battery.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 4 -

Figure 4 Controller Air Blocker

5. Remove the controller canister (Figure 5) that has the failed controller battery.

a. Unlock the release levers, and pull the release lever outward to release the controller canister.

b. Using the release levers and your hands, pull the controller canister out of the base system.

Figure 5 Removing and Replacing a Controller Canister

1. Release Lever

2. Controller Canister

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 5 -

6. Set the controller canister on a flat, static-free surface, with the release lever up.

7. Insert the controller air blocker (Figure 6) into the open controller slot to make sure that correct airflow is

maintained.

Figure 6 Inserting the Controller Air Blocker into the Open Controller Slot

ATTENTION Possible equipment damage – The controller slot cannot remain open for more than three

minutes because of the possibility of overheating the equipment. The controller air blocker fills the

controller slot so that the equipment will not overheat.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 6 -

Replacing the Battery in the Controller

1. Press down on both of the top cover latch buttons (Figure 7), and slide the top cover to the rear of the controller

canister.

Figure 7 Controller Canister Top Cover Latch Buttons

1. Top Cover Latch Buttons

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 7 -

2. Move the locking handle down to pull the failed controller battery out of the controller canister (Figure 8).

Figure 8 Battery and Locking Handle in the Controller

1. Top Cover Latch Buttons

2. Battery Circuit Board

3. Locking Handle

3. Remove the failed controller battery by sliding it towards the rear of the controller canister.

4. Insert the new battery into the controller canister by sliding the new controller battery towards the front of the

controller canister.

NOTE Ensure that the battery slides under the side guide pins as you continue to slide the battery to correctly seat it against the

back surface.

5. Move the locking handle up to secure the new battery circuit board to the controller canister.

ATTENTION If the battery is not correctly seated, you will not be able to reinstall the top cover on the

controller canister as directed later. If you suspect that the new battery is not correctly seated, you might

need to slide the new battery out and insert it again.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller Battery April 2015

Quantum Corporation

- 8 -

6. Reinstall the top cover on the controller canister by sliding the top cover forward until the top cover latch buttons

click.

Reinstalling the Controller into the Array

1. Remove the controller air blocker from the controller slot.

2. Slide the controller canister all the way into the base system. Push the release lever towards the center of the

controller canister to lock it into place.

3. Reconnect all cables that were disconnected when you removed the controller canister.

Use either the GUI (first bullet) or the CLI (second bullet) to take the appropriate controller online.

—From the Hardware pane in the Array Management Window, right-click the picture of the controller that you

want to take offline, and select Advanced >> Place >> Online.

—Run the following command.

SMcli <DNS-network-name-or-IP-address> -c “set controller [(a | b)]

availability=online”;

4. Look at the LEDs on the controller canister (Figure 9) to make sure that the controller is rebooting correctly.

Figure 9 Controller LEDs

1. Host Link 1 Service Action Required LED (Green)

2. Host Link 2 Service Action Required LED (Green

3. Battery Service Action Required LED (Amber)

4. Controller Service Action Allowed LED (Blue)

5. Controller Service Action Required LED (Amber

During the rebooting process, observe the following:

The seven-segment display shows the sequence OS+ Sd+ blank- to indicate that the controller is performing

Start-of-day (SOD) processing.

After the controller successfully completes rebooting, the seven-segment display shows the tray ID matching the

seven-segment display on the second controller.

After this time, you can discover the controller canister with the new battery by using the storage management

software.

5. On both controller canisters, look at the Host Link Service Action Required LEDs and the Controller Service Action

Required LEDs. Based on the LED status, perform one of these actions:

—For each controller, the Host Link Service Action Required LEDs are on and the Controller Service

Action Required LED is off – Go to step 7.

—On one controller, the Host Link Service Action Required LEDs are off, or the Controller Service Action

Required LED is on – Check that the controller canister has been installed correctly. Reinstall the controller

canister, if necessary. Go to step 6.

Otros manuales para StorNext QM1200

Este manual sirve para los siguientes modelos

Otros manuales de Almacenamiento de Quantum

Quantum

Quantum ATL M-Series Manual de usuario

Quantum

Quantum PX506 Manual de usuario

Quantum

Quantum ACL 4/52 Manual

Quantum

Quantum SuperLoader 3A Series Manual del propietario

Quantum

Quantum Scalar i500 Manual de usuario

Quantum

Quantum Tape Drives A-Series Manual de usuario

Quantum

Quantum Scalar 24 Manual de usuario

Quantum

Quantum DLTtape DLT 2000 Manual

Quantum

Quantum Scalar i500 Manual de usuario

Quantum

Quantum StorNext QD7000 Manual de usuario

Quantum

Quantum DLT-V4 Manual de usuario

Quantum

Quantum Atlas 10K III Manual de usuario

Quantum

Quantum Scalar i40 Manual de usuario

Quantum

Quantum Scalar i6000 Manual de usuario

Quantum

Quantum A-Series FTP Manual de instrucciones

Quantum

Quantum QXS-312 Manual técnico

Quantum

Quantum LTO 4 Manual de usuario

Quantum

Quantum Tape Drive SDLT 600A Manual de usuario

Quantum

Quantum Scalar i500 Cómo utilizar

Quantum

Quantum PX502 Manual de referencia

Quantum

Quantum DXi6902 Guía de inicio rápido

Quantum

Quantum Scalar i2000 Manual de instrucciones

Quantum

Quantum DXi4700 Manual de instalación y operación

Quantum

Quantum Scalar i6000 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario