Quantum PX502 Manual de usuario

PX502 Tape Library

Quick Start Guide

TABLE OF CONTENTS

Introduction .......................................1

Notational Conventions .................1

Choosing a Location ..........................2

Rack Space Requirements...............2

Environmental Conditions .............2

Preparing for the Installation ...........2

Providing Necessary Tools ..............2

Taking ESD Precautions ..................2

Unpacking the PX502 Tape Library ...2

Installing the Library .........................3

Locating the Mounting Position ....3

Installing the Library ......................4

Initial Configuration .....................11

Multiple Library Stacks....................15

Introduction 0

The PX502 tape library is an automated storage and retrieval device consisting of

up to two tape drives and up to 32 SDLT cartridges or 38 LTO tape cartridges (see

figure 1).

Notational Conventions 0

This instruction uses the following conventions:

This document explains how to unpack the PX502 tape library and install it in a

standard 19 in. rack. Once the library is unpacked and installed, set up the library

using the instructions in the

PX500 Series

User’s Guide PN 81-81290. This

installation procedure will take approximately 4 hours to complete.

Figure 1 PX502 Tape Library

NOTE:Notes emphasize important information related to the main topic.

CAUTION:Cautions indicate potential hazards to equipment and are included

to prevent damage to equipment.

WARNING:Warnings indicate potential hazards to personal safety and are

included to prevent injury.

NOTE:It is recommended to review the entire document prior to beginning the

installation.

PX502 Tape Library Quick Start Guide

Choosing a Location 0

When choosing an installation site for the PX502, consider

the following requirements:

•Rack Space Requirements

•Environmental Conditions

Rack Space Requirements 0

Ta b l e 1 contains the rack requirements for the PX502 tape

library.

Table 1 Rack Requirements

Environmental Conditions 0

The installation site must have the following environmental

conditions:

• Humidity: 20%-80% non-condensing

• Temperature: 10°C-35°C (50°F-95°F)

• Altitude: -500 to 10,000 feet (-152 to 3048 meters)

These environmental conditions apply when the PX502 tape

library is in operation.

Preparing for the Installation 0

Before you begin the installation procedure in this section,

make the following preparations as described in this

section:

•Providing Necessary Tools

•Taking ESD Precautions

Dimensions PX502

Depth 31 in (78.7 cm)

Width 19 in (48.3 cm)

Height 6.75 in (17 cm), 4U

Weight 52 lbs (23.6 kg)

Air Clearance Open 4 in (10 cm) behind unit

for proper air flow

NOTE:For additional specifications, refer to the

Quantum PX500 Series User’s Guide

(PN 81-

81290)

Providing Necessary Tools 0

Provide the following tools for unpacking and installing the

PX502 tape library:

• #1 PHILLIPS® screwdriver

• #2 PHILLIPS screwdriver

• #1 flat blade screwdriver

• Allen wrench (2.5mm and 3mm) included in accessory

kit

• Antistatic wrist strap included in accessory kit

Ta k i n g E S D P r e c a u t i on s 0

Some components within the PX502 tape library contain

static-sensitive parts. To avoid damaging these parts while

performing installation procedures, always observe the

following precautions:

• Keep the PX502 turned off during all installation

procedures.

• Use an antistatic wrist strap (included in the accessory

kit).

• Keep static-sensitive parts in their original shipping

containers until ready for installation. Look for the ESD

sticker to identify static sensitive parts.

• Avoid touching connectors and other components.

Unpacking the PX502 Tape Library 0

This section explains how to unpack the PX502 tape library

and move it to its final installation location.

NOTE:Dry climates and cold-weather heating

environments have lower relative humidity and

are more likely to produce static electricity.

NOTE:Inspect the outer library packaging for damage. If

there is any damage evident on the library

packaging, do not continue with the installation

and contact Quantum customer support.

PX502 Tape Library Quick Start Guide

By following these instructions, you help ensure that the

system will continue to be safeguarded after it arrives at the

installation site.

Unpack and remove the following components from the

packing materials (see figure 2):

1Remove the accessories kit and set it aside.

2With the help of a second person, lift the library chassis

up and out of the shipping carton.

3Place the library on a table approximately waist high.

Figure 2 Unpacking the PX502

NOTE:Unpack the library as close to the installation

location as possible.

WARNING:At least two people are required to move the

library chassis.

CAUTION:Lift the library chassis at the sides. Avoid

putting the weight of the library chassis on

the front bezel.

Accessory kit

Foam

PX502 tape

library

Foam

Front bezel

Lift point

4Remove the antistatic sheet:

aCut the tape strips securing the sheet.

bFold the sheet down.

cWith the help of a second person, lift the library up

off of the antistatic sheet.

dPlace the library on the table or desk next to the

antistatic sheet.

eIf this is a multiple library stack, refer to “Multiple

Library Stacks” on page 15 before proceeding.

The PX502 is ready to install.

Installing the Library 0

Installing a PX502 tape library in a rack consists of the

following steps:

•Locating the Mounting Position

•Installing the Library

•Initial Configuration

Locating the Mounting

Position 0

The PX502 tape library is designed to fit in a standard 19

inch wide rack.

It is important to the library installation to locate the hole

pattern in the rack rails (see figure 3). The library must be

installed at the beginning of the hole pattern. Refer to

table 2 for information on common rack hole types.

PX502 Tape Library Quick Start Guide

Table 2 Rack Hole Types

Figure Description

Square rack holes are the most

common type of rack holes. They

can accept either cage nuts which

mount from the back of the rail or

clip nuts which clip on from the

side of the rack rail.

Through holes require clip nuts to

accept mounting hardware.

Threaded holes require neither

cage or clip nuts to accept

mounting hardware.

NOTE:The rails within the rack have a hole pattern that

repeats throughout the rail. Xmarks the screw

positions. Install nut clips (included in the

accessory kit) on the rails if necessary.

Cage nut

Clip nut

Figure 3 Rail Hole Pattern

Installing the Library 0

Installing the PX502 tape library consists of the following

steps:

•Installing the Rack Mount Shelves

•Installing the Library Chassis

•Cabling the Library

WARNING:If the rack is empty at the time of installation,

do NOT install the PX502 tape library too

high in the rack. The weight of the library

may cause the rack to become “top heavy”

and unstable if installed in the top of an

empty rack. Begin installing the PX502 tape

library from the bottom of the rack if more

than one library is installed.

NOTE:If this is an upgrade to an existing library system,

see “Multiple Library Stacks” on page 15.

.625 in (15.9 mm)

.5 in (12.7 mm)

.625 in (15.9 mm)

Top of rack

.312 in (7.92 mm)

.5 in (12.7 mm)

Hole pattern

The marks above (X)

indicate the location of

mounting hardware on the

rack rails. Ensure that any

necessary mounting

hardware is installed on the

rack rails prior to installing

the chassis.

1 PX502 System (4U)

1U = 1.75 in

(44.45mm)

Front panel screws

mounting positions

Back panel screws

mounting positions

Front panel screws

mounting positions

PX502 Tape Library Quick Start Guide

Table 3 Library Mounting Hardware

Qty Figure Description

16 Allen head screws (M5

x 10) for shelf

assembly

PN 90-87203-01

8 T- nuts (M5)

PN 74-87575-01

4 metric

and 4

standard

Rail adapters (both

metric and standard

holes are included, 8

total adapters, see

figure 6)

PN 74-88052-01

(metric)

PN 74-88053-01

(standard)

2 Right and left support

shelves (left shown)

PN 74-88055-01

(shelf)

PN 74-88056-01

(extender)

4 sets Front and back rail

mountinghardware

(M4 x 12 allen screws

and mounting plates)

PN 74-88054-01

(plate)

PN 90-87203-03

(screws)

2 sets Back bracket hardware

(M5 x 8 allen screws

and mounting plate)

PN 74-88057-01

(bracket)

PN 90-87275-01

(screws)

2 sets Back clamp hardware

(M5 x 10 and back

clamp)

PN 90-87343-08

(screws)

PN 74-88058-01

(clamp)

Extender

Shelf

Installing the Rack Mount Shelves

Before installing the rack mount shelves, you must collect

the following information:

• Type of rack mount rails (square hole, through hole, or

threaded hole)

• Depth of rack (34 in, 86.3 cm minimum depth

recommended; however, rack depths of 24 in, 60.9 cm

to 36 in, 91.4 cm are supported)

1Assemble the rack mount shelves (left and right):

aDetermine the mounting hole locations. The holes

used to attach the two halves of the rack mount

shelves differ depending on the depth of the rack

(see figure 4).

PX502 Tape Library Quick Start Guide

Figure 4 Rack Mount Shelf Depth

Requirements

bLoosely attach the adjustable rack mount shelves

(extenders and shelves) with 4 M5 x 10 Allen screws

and T-nuts (see figure 7).

Use these holes for rack

depths of 27 in (68.5 cm)

to 36 in (91.4 cm)

Use these holes for rack

depths of 24 in (60.9 cm)

to 28 in (71.1 cm)

Left shelf oriented

with FlexLink™

opening toward front

of rack

Use these holes for rack

depths of 27 in (68.5 cm)

to 36 in (91.4 cm)

Use these holes for rack

depths of 24 in (60.9 cm)

to 28 in (71.1 cm)

Right shelf oriented

with FlexLink opening

toward back of rack

Front of rack

Back of rack

Front of rack

Figure 5 Assembling the Left and

Right Rack Mount Shelves

cDetermine the type of rail adapter required for your

rack. Each rail adapter is marked with the specific

hole type supported, either metric or standard (see

figure 6).

M5 x 10 Allen screws

T-nuts

Left-hand rackmount shelf

Right-handrackmountshelf

T-nuts must be

oriented as

shown to properly

fit in the shelf

adjustment slot

T-nuts must be oriented as

shown to properly fit in the

shelf adjustment slot

The metal fold

must be toward

the outside of

the self as

shown

The metal fold

must be toward

the outside of

the self as

shown

Back of rack

Front of rack

Back of rack

Extender

PX502 Tape Library Quick Start Guide

Figure 6 Rail Adapter Types

dAttach the appropriate rail adapter to the front and

back of the rack mount shelves (right and left) with 2

M5 x 10 Allen screws per adapter (see figure 7).

Use the rail adapters with

blocks on rails with square

hole patterns

Use the rail adapters with

circle pegs (opposite blocks)

on rails with non-threaded

circle hole patterns

Use the rail adapters with

small circle pegs on rails

with threaded circle hole

patterns (M6 on one side and

M5 on the other side)

Figure 7 Assembling the Left-

Hand Rack Mount Shelf

2Install the left and right rack mount shelves into the

rack (the rack mount shelves adjust 27 in. to 36 in.) and

secure with the following parts in four locations (see

figure 8):

• Mounting plate

• 2 M4 x 12 Allen screw.

NOTE:The rack mount shelves must be installed on the

inside rack rails.

M5 x 10 Allen

screws

Rail adapter

Leftshelf

FlexLink opening

located towards the

back for the right-

hand shelf

Arrow must

point up

M5 x 10 Allen

screws

M5 x 10 Allen

screws

Rail adapters

Rightshelf

M5 x 10 Allen

screws

Rail adapter

Arrow must

point up

PX502 Tape Library Quick Start Guide

Figure 8 Installing the Rack

Mount Shelves

3Once the rack mount shelves are secured to the rack,

tighten the Allen screws securing the adjustable shelves

(right and left) together (see figure 9).

Left shelf

Right shelf

Mounting

plate

M4 x 12

Allen screws

Figure 9 Tightening the Rack

Mount Shelves

Installing the Library Chassis

1The back mounting brackets are lettered (A through I)

so the correct mounting position is easily determined.

The mounting positions differ depending on the depth

of the rack (see table 4).

WARNING:The PX502 tape library weighs approximately

52 lbs (23.6 kg). At least two people are

required to lift and install the library.

NOTE:If the depth of the rack is less than 27 in, do not

install the back mounting brackets or clamps.

Tighten screws to secure

both rack mounting rails

PX502 Tape Library Quick Start Guide

Table 4 Back Mounting Bracket

Orientation

Once the location is determined, attach the back

brackets to each side of the library with four M5 x 8

Allen screws (see figure 10).

Rack Depth Back Mounting

Bracket

(Mounting

Position)

Back Mounting

Clamp

Holes

24 to 25 in. Back bracket and

clamp not required

N/A N/A

25 to 26 in. Back bracket and

clamp not required

N/A N/A

26 to 27 in. Back bracket and

clamp not required

N/A N/A

27 to 28 in. Use holes A and C X

28 to 29 in. Use holes B and D X

29 to 30 in. Use holes C and E X

30 to 31 in. Use holes D and F X

31 to 32 in. Use holes E and G X

32 to 33 in. Use holes F and H X

33 to 34 in. Use holes G and I X

34.5 to 35.5 in. Use holes F and H X

35.5 to 36.5 in. Use holes G and I X

NOTE:If your rack has a depth less than 27 in., the back

brackets and back clamps are not used.

#1 Holes

#2 Holes

Back mounting bracket

Back mounting clamp

Figure 10 Installing the Back

Mounting Brackets

2Install the library into the rack as shown in figure 11

and secure the library to the rack with four PHILLIPS

screws.

Figure 11 Installing the PX502 in

the Rack

NOTE:If this is a multiple stack configuration, refer to

“Multiple Library Stacks” on page 15 for

information on preparing the library chassis for

passing tape cartridges from one unit to another.

WARNING:The PX502 tape library weighs approximately

52 lbs (23.6 kg). At least two people are

required to lift and install the library.

Right-hand back

bracket shown.

Back mounting

bracket

M5 x 8 Allen

screws

PHILLIPS screws

PX502 Tape Library Quick Start Guide

3Secure the back of the library to the rack with two

mounting clamps (refer to table 4 for information on

the correct mounting holes to use) and two M5 x 10

Allen screws on each clamp (see figure 12).

4Secure the mounting clamps to the rack rails with two

PHILLIPS screws on each side (see figure 12).

Figure 12 Securing the Back of

the Library

5To install the tape drives into the library:

aRemove the tape drive cover plates (if necessary,

some libraries ship with one tape drive installed) by

loosening the captive screws securing the plate to

the library chassis (see figure 13).

NOTE:If the depth of the rack is less than 27 in, do not

install the back mounting brackets or clamps.

Left-hand back

bracket shown.

M5 x 10

Allen screws

PHILLIPS

screws

Back mounting

clamp

Figure 13 Removing the Tape

Drive Cover Plates

bInsert the tape drive(s) into the drive bay(s) slowly

until the connectors are seated. Refer to figure 14 for

drive bay numbering (see the

Quantum PX500 Series

Tape Drive Installation Instructions

PN 81-81301 for

information).

Figure 14 Installing the Tape

Drives

cTighten the tape drive thumbscrews using a flat

blade screwdriver.

dRepeat these steps to install another tape drive in a

different location, if desired.

The library chassis is installed in the rack.

Cabling the Library

1Connect the SCSI cables and jumpers as shown in the

following figures:

•Figure 15 SCSI System Controller Board

•Figure 16 Surrogate SCSI System Controller Board

Cover plate

Tape

drive

bay 1

Tape drive

bay 2

Tape

drive 2

Ta p e

drive 1

Back of Library

Otros manuales para PX502

Tabla de contenidos

Otros manuales de Almacenamiento de Quantum

Quantum

Quantum DLTtape SDLT 220 Hoja de información del producto

Quantum

Quantum QDFLD25-***MUH1I Series Manual de usuario

Quantum

Quantum Quantum Bigfoot CY Manual de usuario

Quantum

Quantum DLTtape SDLT 600 Hoja de información del producto

Quantum

Quantum DXi V-Series Manual de usuario

Quantum

Quantum DLT-S4 Manual de usuario

Quantum

Quantum StorNext QD7000 Manual de usuario

Quantum

Quantum LTO-4 (Model B) Manual de usuario

Quantum

Quantum DXi4601 Manual de usuario

Quantum

Quantum DX100 Manual de lista de piezas

Quantum

Quantum Scalar LTFS Manual de uso y cuidado

Quantum

Quantum StorNext QS1200 Manual de usuario

Quantum

Quantum DXi6900-S Manual de usuario

Quantum

Quantum StorNext QM1200 Manual de usuario

Quantum

Quantum StorNext QD7000 Instrucciones de instalación

Quantum

Quantum PX506 Manual de usuario

Quantum

Quantum LTO3 A-Series Manual de usuario

Quantum

Quantum DPM 5500 Manual de usuario

Quantum

Quantum DLT 8000 Manual

Quantum

Quantum QX Series Manual de usuario

Quantum

Quantum Scalar i2000 Manual de instrucciones

Quantum

Quantum LTO-8 HH SAS Manual del producto

Quantum

Quantum StorNext QD6000 Manual de usuario

Quantum

Quantum StorNext QD6000 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario