Pyle PLCAPE500 Manual de usuario
1
Model: PLCAPE500
50F Hybrid Super Cap (carbon and eletroniccapacitor)
With Blue Digital Voltage Display
Capacitance .................................……...... 50,000,000 micro farad (50
Farad)
Working Voltage ...............................…….….. 16DC
Surge Voltage .......................................……… 18DC
E.S.R. (Equivalent Series Resistance)------ 0.0015 ohm @120hz/ 25°C
Capacitance Tolerance------------------------ ± 10%
a) 3 digits hi-end blue light display DC voltage meter that can measure
0.1 DCV range.
b) Reverse pole connecting PCB buzz warning function. If the capacitor is
connected incorrectly by reversing the positive and negative wires
during the installation process the PCB will issue a 45 second noise to
warn you.
c) Hi-end platinum plated 100% brass solid parts and chrome plated metal
cover
d) Over voltage limit and low battery voltage limit warning. When the
system voltage peeks over 17.5 DCV or LESS than 10 DCV. The
buzzer on the PCB will issue an audible noise warning.
e) Multiple small capacitance capacitors linked to provide the lowest
inner E.S.R. and largest moment discharge power.
DETAILED FEATURES:
2
You must first attach the mounting tabs to the capacitor before mounting
it. Use the supplied hardware shown in the picture to the right. Notice the
small mounting screw hole in the capacitor chassis.
3
CHARGING THE CAPACITOR AND WIRING:
The capacitor must be charged before connecting the Power and Ground
cables to the capacitor. Failure to charge the capacitor will result in a
large spark generated from the rapid inflow ofcurrent.
To Charge the capacitor:
1. Make Capacitor positive terminal connections with amplifier and
tighten the bolt. Do not over-tighten the bolts!
Caution: Stripped terminals are not covered under the capacitor’s
warranty.
2. Connect the ground cable with battery, amplifier, then refer to the
attached drawing.
3. Place the supplied charging bulb or resistor between the positive
terminal of the capacitor and the battery’s positive terminal. Do this
for 30 seconds or until the charging bulb goes out.
Caution: The charging bulb will get hot!
4. Immediately after the charging process, take out the charging bulb
from the connecting wire. And connect the positive cable of the
battery directly to the positive terminal on the capacitor.
WHEN YOU WANT TO MOVE THE CAPACITOR FROM
ORIGINAL INSTALLED CAR AUDIO SYSTEM, YOU MUST FIRST
FOLLOW DISCHARGING PROCESS AFTER TAKING OUT THE
CAPACITOR FROM THE CAR AUDIO SYSTEM.
4
To Discharge the capacitor: With battery power disconnected, place the
light bulb or resistor across the capacitor’s positive and negative terminals
until light goes out or for three minutes if using a resistor.
!
! !
!
5
"
" "
"
One Year Warranty from the date of purchase.
##
####
##
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Pyle
Pyle
Pyle WatchDog PLPSE3 Manual de usuario
Pyle
Pyle PLFMTR9BT Manual de usuario
Pyle
Pyle PLD94BK Manual de usuario
Pyle
Pyle PLDCP50 Manual de usuario
Pyle
Pyle PBT98 Manual de usuario
Pyle
Pyle PLCM21 Manual de usuario
Pyle
Pyle PLCMDVR 8 Manual de usuario
Pyle
Pyle PLCM7500 Manual de usuario
Pyle
Pyle PLCM9200 Manual de usuario
Pyle
Pyle PLCMDVR72 Manual de usuario
Pyle
Pyle PLCM34WIR Manual de usuario
Pyle
Pyle PLCPBT25 Manual de usuario
Pyle
Pyle PLCM4235 Manual de usuario
Pyle
Pyle PLCMTR26 Manual de usuario
Pyle
Pyle PLPSC8 Manual de usuario
Pyle
Pyle PLCM9200 Manual de usuario
Pyle
Pyle PLCMTR83WIR Manual de usuario
Pyle
Pyle PBT96 Manual de usuario
Pyle
Pyle PHUD19 Manual de usuario
Pyle
Pyle PLCM4300WIR Manual de usuario
