Pyle PLCAPE30 Manual de usuario

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Pyle

Pyle

Pyle PLCAPE24 Manual de usuario

Pyle

Pyle PLCM7500 Manual de usuario

Pyle

Pyle PIFMDK6 Manual de usuario

Pyle

Pyle PLD94BK Manual de usuario

Pyle

Pyle PBT99 Manual de usuario

Pyle

Pyle PLDCP50 Manual de usuario

Pyle

Pyle PLRD146 Manual de usuario

Pyle

Pyle PLCMDVR 8 Manual de usuario

Pyle

Pyle PLCM4300WIR Manual de usuario

Pyle

Pyle PHUD19 Manual de usuario

Pyle

Pyle PLCM34WIR Manual de usuario

Pyle

Pyle PLCMTRDVR47 Manual de usuario

Pyle

Pyle PLCM9200 Manual de usuario

Pyle

Pyle PLPSC8 Manual de usuario

Pyle

Pyle PLCAPE500 Manual de usuario

Pyle

Pyle PLCMTR83WIR Manual de usuario

Pyle

Pyle PLFMTR9BT Manual de usuario

Pyle

Pyle PLCMTR26 Manual de usuario

Pyle

Pyle PLCMDVR72 Manual de usuario

Pyle

Pyle PLCPBT25 Manual de usuario

Pyle

Pyle BlueTech PBT70R Manual de usuario

Pyle

Pyle PLDCP25 Manual de usuario

Pyle

Pyle PLCMDVR 42 Manual de usuario

Pyle

Pyle PLCMRV8B Black Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

Model: PLCAPE30

3 FARAD DIGITAL CAPACITOR WITH RED DISPLAY )

Capacitance .................................……............. 1,200,000 micro farad

Working Voltage ...............................…….….. 21DC

Surge Voltage .......................................……… 24DC

E. S. R. (Equivalent Series Resistance) ..…….. 0.0012 ohm @ 120hz/25

Capacitance Tolerance …………………..…… ±10%

We recommend at least 1 Farad of capacitance per 500 watts of amplifier output. This is a

general rule of thumb and may be adjusted up or down depending on the efficiency and design of the

amplifiers being used. There is no harm in having more than enough capacitance.

DETAILED FEATURES:

a) 4 digital 8 RED display voltage meter that can measure 0.01 DCV range.

b) Blue Light PCB

c) Over voltage limit and low battery voltage limit warning. When the system voltage peeks over

17.5 DCV or LESS than 10 DCV. The buzzer on the PCB will issue an audible noise warning.

d) Reverse pole connecting PCB buzz warning function. If the capacitor is connected incorrectly

by reversing the positive and negative wires during the installation process the PCB will issue

a 45 second noise to warn you.

e) Lowest E. S. R. 24 DCV foil with maximum moment discharge power in lowest E.S.R..

f) Hi-end chrome/black chrome/satin nickel plated finish solid capacitor casing.

+)(

--

( )

To Charge the capacitor:

1. Make your connections from the Capacitor positive and negative output terminals to the

amplifier(s) positive and negative terminals. Do not over-tighten the bolts on the Capacitor!

Caution: Stripped terminals are not covered under the capacitor’s warranty.

2. Connect the battery ground cable directly to the capacitor, then refer to the attached

drawing.

3. Place the supplied charging bulb or resistor between the positive terminal of the capacitor

and the battery’s positive terminal. Do this for 30 seconds or until the charging bulb goes

out. Caution: The charging bulb will get hot!

4. Immediately after the charging process, take out the charging bulb from the connecting

wire. And connect the positive cable of the battery directly to the positive terminal on the

capacitor.

5. Follow the attached wiring drawing to connect all wire and parts.

Below is an illustration showing correct wiring for the capacitor.

BA TTERY

--

(+)()

DISCHARGING THE CAPACITOR:

WHEN YOU WANT TO MOVE THE CAPACITOR FROM THE ORIGINAL INSTALLED CAR

AUDIO SYSTEM. YOU MUST FIRST DISCHARGE THE CAPACITOR USING THIS PROCESS

BEFORE REMOVING THE CAPACITOR FROM THE CAR AUDIO SYSTEM.

To Discharge the capacitor: With the battery power disconnected, place the light bulb or resistor across

the capacitor’s positive and negative terminals until the light goes out or for three minutes if using a

resistor.

INSTALLATION AND WIRING

Multiple Capacitor Wiring Diagram

One Year       

            

                   

                          

                   

              

        











WARRANTY APPLIES ONLY TO THE PRODUCTS SOLD TO CONSUMERS BY

AUTHORIZED DEALERS IN THE UNITED STATES OF AMERICA OR ITS POSSESSIONS.

OUTSIDE OF THE USA, ONLY THAT COUNTRY’S DISTRIBUTOR COVERS PRODUCTS

PURCHASED BY CONSUMERS FROM OVERSEA AUTHORIZED DEALER.