Prorack K954 Manual de usuario
K954
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 4
Revision No: 4D 1
Fitting Kit K954
MAX kgs (lbs)
W/P WHD
Toyota
Fortuner GX, 5dr SUV 16-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Fortuner GX, 5dr SUV Nov 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Double Cab, 4dr Ute 16-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Double Cab, 4dr Ute 16-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Double Cab, 4dr Ute Oct 15-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Double Cab, 4dr Ute Oct 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Extra Cab, 2dr Ute 16-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Extra Cab, 2dr Ute 16-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Extra Cab, 2dr Ute Oct 15-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Extra Cab, 2dr Ute Oct 15-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Hilux Single Cab, 2dr Ute 16-+ EU 35 kgs (77 lbs) 50 kgs (110 lbs)
Hilux Single Cab, 2dr Ute 16-+ ZA 35 kgs (77 lbs) 50 kgs (110 lbs)
Hilux Single Cab, 2dr Ute Oct 15-+ AU 35 kgs (77 lbs) 50 kgs (110 lbs)
Hilux Single Cab, 2dr Ute Oct 15-+ NZ 35 kgs (77 lbs) 50 kgs (110 lbs)
2
Fitting Kit K954
X
A B C 1 2 3
Fortuner GX, 5dr SUV 16-+ (NZ) -230mm 465mm - 880mm 880mm -
-9 -1/16ths" 18 5/16ths" - 34 5/8ths" 34 5/8ths" -
Fortuner GX, 5dr SUV Nov 15-+ (AU) -230mm 465mm - 880mm 880mm -
-9 -1/16ths" 18 5/16ths" - 34 5/8ths" 34 5/8ths" -
Hilux Double Cab, 4dr Ute 16-+ (EU) -200mm 500mm - 885mm 885mm -
-7 -7/8ths" 19 11/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Double Cab, 4dr Ute 16-+ (ZA) -200mm 500mm - 885mm 885mm -
-7 -7/8ths" 19 11/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Double Cab, 4dr Ute Oct 15-+ (NZ) -200mm 500mm - 885mm 885mm -
-7 -7/8ths" 19 11/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Double Cab, 4dr Ute Oct 15-+ (AU) -200mm 500mm - 885mm 885mm -
-7 -7/8ths" 19 11/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Extra Cab, 2dr Ute 16-+ (EU) -350mm 300mm - 885mm 885mm -
-13 -3/4ths" 11 13/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Extra Cab, 2dr Ute 16-+ (ZA) -350mm 300mm - 885mm 885mm -
-13 -3/4ths" 11 13/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Extra Cab, 2dr Ute Oct 15-+ (AU) -350mm 300mm - 885mm 885mm -
-13 -3/4ths" 11 13/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Extra Cab, 2dr Ute Oct 15-+ (NZ) -350mm 300mm - 885mm 885mm -
-13 -3/4ths" 11 13/16ths" - 34 13/16ths" 34 13/16ths" -
Hilux Single Cab, 2dr Ute 16-+ (EU) -200mm - - 885mm - -
-7 -7/8ths" - - 34 13/16ths" - -
Hilux Single Cab, 2dr Ute 16-+ (ZA) -200mm - - 885mm - -
-7 -7/8ths" - - 34 13/16ths" - -
Hilux Single Cab, 2dr Ute Oct 15-+ (AU) -200mm - - 885mm - -
-7 -7/8ths" - - 34 13/16ths" - -
Hilux Single Cab, 2dr Ute Oct 15-+ (NZ) -200mm - - 885mm - -
-7 -7/8ths" - - 34 13/16ths" - -
3
Fitting Kit EN
K954
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K954
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K954
●Remove locking screw.
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 244
6
Fitting Kit EN
K954
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
●Apply protective strip as shown.
Trim if required.
7
Fitting Kit EN
K954
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A715
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
8
Fitting Kit EN
K954
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
9
Fitting Kit EN
K954
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Prorack
Prorack
Prorack K596 Manual de usuario
Prorack
Prorack K446 Manual de usuario
Prorack
Prorack K333 Manual de usuario
Prorack
Prorack K757 Manual de usuario
Prorack
Prorack K525 Manual de operación e instalación
Prorack
Prorack K308 Manual de usuario
Prorack
Prorack K130 Manual de usuario
Prorack
Prorack K848 Manual de usuario
Prorack
Prorack K701 Manual de usuario
Prorack
Prorack PR3600 Manual de usuario
Prorack
Prorack K919 Manual de usuario
Prorack
Prorack K340 Manual de usuario
Prorack
Prorack PR3075 Guía de instalación
Prorack
Prorack K1188 Manual de usuario
Prorack
Prorack K449 Manual de usuario
Prorack
Prorack K042 Manual de usuario
Prorack
Prorack K786 Manual de usuario
Prorack
Prorack K869 Manual de usuario
Prorack
Prorack K425 Manual de usuario
Prorack
Prorack Fitting Kit K440 Manual de usuario
