Prorack K042 Manual de usuario
K042
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 4
Revision No: 4C 1
Fitting Kit K042
MAX kgs (lbs)
W/P WHD
Volvo
740 , 3dr Sedan 84-Dec 93 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Daewoo
Cielo , 3dr Hatch 94-98 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 3dr Hatch Sep 95-Jul 98 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 4dr Sedan 94-98 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 4dr Sedan 95-97 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 4dr Sedan Aug 95-Apr 98 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 5dr Hatch 94-98 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 5dr Hatch Aug 95-Apr 98 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Cielo , 5dr Hatch Sep 95-Jul 98 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Le Mans , 4dr Sedan 87-94 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Le Mans , 5dr Hatch 87-94 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Opel
Kadett , 3dr Hatch 85-91 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Kadett Gsi, 3dr Hatch Nov 84-Jan 91 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Pontiac
Le Mans , 4dr Sedan Sep 87-Mar 93 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit EN
K042
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K042
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K042
●Remove locking screw.
●Cut protective strip in four equal lengths.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
5
Fitting Kit EN
K042
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
6
Fitting Kit EN
K042
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
7
Fitting Kit EN
K042
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
8
Fitting Kit EN
K042
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
9
Fitting Kit EN
K042
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
10
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Prorack
Prorack
Prorack K985 Manual de usuario
Prorack
Prorack K112 Manual de usuario
Prorack
Prorack K1001 Manual de usuario
Prorack
Prorack K175 Manual de usuario
Prorack
Prorack K494 Manual de usuario
Prorack
Prorack Whispbar Q20 Manual de usuario
Prorack
Prorack PR3206 Manual de usuario
Prorack
Prorack K982 Manual de operación e instalación
Prorack
Prorack K877 Manual de operación e instalación
Prorack
Prorack K848 Manual de usuario
Prorack
Prorack K571 Guía de instalación
Prorack
Prorack K587 Manual de usuario
Prorack
Prorack K629 Manual de usuario
Prorack
Prorack K1010 Manual de usuario
Prorack
Prorack K186 Manual de usuario
Prorack
Prorack K552 Manual de usuario
Prorack
Prorack K1125 Manual de usuario
Prorack
Prorack K677 Manual de operación e instalación
Prorack
Prorack K038 Manual de usuario
Prorack
Prorack PR3213 Manual de usuario
