PROAIM P-PTBH-01 Manual de usuario
1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
PhotoBooth Studio Kit - Camera
Plaorm (P-PTBH-01)
Assembly Manua l
22" Telescoping Arm
Vesa Studio Monitor
Mount for Stand
Arculang Arm
Camera Plaorm
Cold Shoe Mount
(Baby Stud Adapter with
1/4″ 20 female thread on
one side and 3/8″ female
thread
on the other side)
2
Mount the monitor mount on the C-stand and
ghten it using the back knob.
Note: Monitor Mount is the best way to mount
your LCD monitor on a C-stand, light-stand, or
other stands with 5/8" baby pins/studs.
The images show that you can move the
monitor mount up and down up to 90° using
the side knob.
Set the monitor mount at the desired posion
and secure it properly using the knob. Loosen
the knob to remove the monitor mount.
Mount it on the stand via the 2nd mounng
point.
Note: Monitor Mount has two side mounng
opons to change the direcon of the monitor.
Change the direcon according to your
requirements and ghten the knob from the
2nd side to secure the monitor mount.
Monitor Mount Setup
Screw together the LCD and the monitor
mount and secure them properly using an
Allen key, as shown in the image.
Note: The monitor is mounted via four screws.
Once secured, you can lt the monitor to any
viewing posion by the provided knob.
Note: You can mount your at-panel monitor up
to 32" (diagonally measured).
3
Loosen the knob of the arculang arm, and
open the arm completely. Align and insert the
arm into the thread on the monitor mount.
Note: The arculang arm is movable and helps
move the camera's direcon.
Once the arculang arm is inserted, secure it
correctly with the help of the knob, as shown
in the image.
Mount the camera plaorm on the arculang
arm and secure it using the center knob.
Note: Robust Camera Plaorm allows you to
safely mount a camera to the arculang arm,
as shown in the image.
Arculang Arm Setup
Note: Camera Plaorm has 1/4 "-20 & 3/8 "-16
threaded camera studs and two 5/8" receivers
to mount compable accessories of your choice.
Camera Plaorm Setup
To change the camera's movement, loosen the
knob of the arculang arm, set the direcon,
and ghten the knob back.
4
Loosen the knob of the cold shoe mount, and
extend it completely.
Note: Cold Shoe Mount Baby Stud Adapter has
1/4″ 20 female thread on one side and 3/8″ fe-
male thread on the other side.
Insert the 22" telescoping arm into the
monitor mount and secure it with the help of
the knob.
Note: You can use the Proaim 20" Telescoping
Arm for everything from overhead lighng to
stand extension.
Note: Twist the knob, and the aluminum arm
telescopes from 11.5" to 20" in length. Each end
has a 5/8" stud topped with 3/8" threads for
receiver or screw-in mounng opons.
Aer extending the length of the telescoping
form, secure it through the knob.
22” Telescoping Arm Setup
Cold Shoe Mount Setup
Images showing dierent arm movements.
Mount the cold shoe mount on the telescopic
arm and secure it with the knob.
5
Image showing Monitor Mount, Arculang
Arm, Camera Plaorm, 22" Telescoping Arm &
Cold Shoe Mount assembled adequately.
Insert the umbrella into the clamp and secure
it correctly with the knob.
Note: This umbrella has been specially designed
for the photobooth setup.
Image showing umbrella assembled
adequately.
Slide the ash onto the cold shoe mount and
ghten it with the help of a bolt.
Note: With the Photobooth Kit, you can aach
a camera on the camera plaorm, a display on
the monitor mount, a ash on the cold shoe
mount, and an umbrella o qn the clamp.
Image showing a praccally complete booth
with a camera, display, ash, and umbrella.
6
YOUR PROAIM PHOTOBOOTH STUDIO KIT - CAMERA PLATFORM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
Tabla de contenidos
Otros manuales de Accesorios para cámaras de PROAIM
PROAIM
PROAIM MB-10 Manual de usuario
PROAIM
PROAIM Polaris Mini Manual de usuario
PROAIM
PROAIM P-UTRA-01 Manual de usuario
PROAIM
PROAIM JB-FLMS-01 Manual de usuario
PROAIM
PROAIM CINEMA TP-BIPT-01 Manual de usuario
PROAIM
PROAIM VI-SPCM-01 Manual de usuario
PROAIM
PROAIM P-WV-2PL Manual de usuario
PROAIM
PROAIM Fusion Manual de usuario
PROAIM
PROAIM P-FT-J Manual de usuario
PROAIM
PROAIM CINEMA LV-4WAY-01 Manual de usuario
PROAIM
PROAIM WS-284-00 Manual de usuario
PROAIM
PROAIM RCSW-CNBD-01 Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM ROM-1 Manual de usuario
PROAIM
PROAIM FF-FCBE-01 Manual de usuario
PROAIM
PROAIM Spinhawk Professional Manual de usuario
PROAIM
PROAIM P-SBP-01 Manual de usuario
PROAIM
PROAIM SC-03 Manual de usuario
